Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.05
RM2070E _53 Suspension _061921 TIRE PRESSURE MONITORING _0301678 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light illuminates and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. DTC Detection Condition Trouble Area
C2198/98 Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Wire harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C270966E34
5.177,2.948 6.563,3.552 1.385,0.604 10 false Tire Pressure Warning ECU and Receiver 1.813,1.469 4.156,1.948 2.344,0.479 10 false Tire Pressure Warning Reset Switch 1.823,1.323 2.198,1.531 0.375,0.208 10 false L164 2.281,0.896 2.385,1.073 0.104,0.177 10 false 2 3.406,0.896 3.51,1.073 0.104,0.177 10 false 1 5.26,0.885 5.458,1.146 0.198,0.26 10 false 3 5.438,1.021 5.917,1.219 0.479,0.198 10 false CLSW 2.479,0.906 2.604,1.083 0.125,0.177 10 false E 3.115,0.906 3.365,1.063 0.25,0.156 10 false INT 5.177,2.802 5.615,3.021 0.438,0.219 10 false R42

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.
C239105E01
0.135,0.096 0.430,0.425 0.295,0.330 10 *a 1.439,1.143 1.685,1.285 0.246,0.142 10 *b 1.843,1.68 2.152,1.822 0.309,0.142 10 *c 2.368,1.64 2.608,1.798 0.240,0.158 10 E 2.914,1.64 3.243,1.798 0.329,0.158 10 INT 2.577,1.245 2.441,1.61 false 2.861,1.245 3.003,1.617 false

Remove the tire pressure warning reset switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (INT) - 2 (E) On Below 1 Ω
Off 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(Tire Pressure Warning Reset Switch)
*b On
*c Off

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

B

C

2.CHECK HARNESS AND CONNECTOR (RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the L164 tire pressure warning reset switch connector.


b.

Disconnect the R42 tire pressure warning ECU and receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R42-3 (CLSW) - L164-1 (INT) Always Below 1 Ω
R42-3 (CLSW) or L164-1 (INT) - Body ground Always 10 kΩ or higher
L164-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR