Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.11–2017.12
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C156569E02
0.25,0.213 0.489,0.390 0.239,0.177 10 *a

Text in Illustration
*a Component without harness connected
(Skid Control ECU)
- -

Terminal No. (Symbol) Terminal Description
1 (MRI1) Motor power supply input 1
2 (MRI2) Motor power supply input 2
3 (STP0)*1 Stop light control relay output
4 (TS) Sensor check switch input
5 (FR-) Front speed sensor RH (-) signal input
6 (STP2)*1 Stop light control relay input
7 (RL-) Rear speed sensor LH (-) signal input
8 - (Not used)
9 (RR-) Rear speed sensor RH (-) signal input
10 - (Not used)
11 (SP1) Speed sensor signal output
12 (IG2) IG2 power source input
13 - (Not used)
14 (BI) +B power source input
15 (BS) Solenoid power supply input
16 (IG1) IG1 power source input
17 - (Not used)
18 (FR+) Front speed sensor RH (+) power supply output
19 (CTY) Courtesy switch input
20 (RL+) Rear speed sensor LH (+) power supply output
21 - (Not used)
22 (RR+) Rear speed sensor RH (+) power supply output
23 (GND6) Skid control ECU ground 6
24 (GND5) Skid control ECU ground 5
25 (GND4) Skid control ECU ground 4
26 (GND3) Skid control ECU ground 3
27 (GND2) Skid control ECU ground 2
28 (GND) Skid control ECU ground
29 (MRO1) Motor power supply output 1
30 (MRO2) Motor power supply output 2
31 (FL+) Front speed sensor LH (+) power supply output
32 (FL-) Front speed sensor LH (-) signal input
33 (STP) Stop light switch input
34 (CA2L) CAN communication line 2 (L)
35 (CA2H) CAN communication line 2 (H)
36 (LBL) Brake fluid level warning switch input
37 (CA1H) CAN communication line 1 (H)
38 (CA1L) CAN communication line 1 (L)
39 (VCSK) Stroke sensor power supply output
40 (SKS2) Stroke sensor signal input 2
41 (SKG) Stroke sensor ground
42 (SKS) Stroke sensor signal input

*1: w/ Dynamic Radar Cruise Control



TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

U154694E03
0.323,0.229 0.5,0.385 0.177,0.156 10 false *a 1.573,1.542 1.844,1.688 0.271,0.146 10 false A58

Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)
- -

HINT:

Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.


Standard
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-1 (MRI1) - Body ground B - Body ground Motor power supply input 1 Always 11 to 14 V
A58-2 (MRI2) - Body ground R - Body ground Motor power supply input 2 Always 11 to 14 V
A58-3 (STP0) - Body ground*1 Y - Body ground Stop light control relay output Always 11 to 14 V
A58-6 (STP2) - Body ground*1 L - Body ground Stop light control relay input Stop light switch ON → OFF
(Brake pedal depressed → released)
11 to 14 V → Below 1.5 V
A58-12 (IG2) - Body ground BE - Body ground IG2 power source input Power switch on (IG) 11 to 14 V
A58-14 (BI) - Body ground W - Body ground +B power source input Always 11 to 14 V
A58-15 (BS) - Body ground B - Body ground Solenoid power supply input Always 11 to 14 V
A58-16 (IG1) - Body ground B - Body ground IG1 power source input Power switch on (IG) 11 to 14 V
A58-19 (CTY) - Body ground V - Body ground Courtesy switch input Driver door close → open 11 to 14 V → Below 1.5 V
A58-23 (GND6) - Body ground W-B - Body ground Skid control ECU ground 6 Always Below 1 Ω
A58-24 (GND5) - Body ground W-B - Body ground Skid control ECU ground 5 Always Below 1 Ω
A58-25 (GND4) - Body ground W-B - Body ground Skid control ECU ground 4 Always Below 1 Ω
A58-26 (GND3) - Body ground W-B - Body ground Skid control ECU ground 3 Always Below 1 Ω
A58-27 (GND2) - Body ground W-B - Body ground Skid control ECU ground 2 Always Below 1 Ω
A58-28 (GND) - Body ground W - Body ground Skid control ECU ground Always Below 1 Ω
A58-33 (STP) - Body ground L - Body ground Stop light switch input Stop light switch ON → OFF
(Brake pedal depressed → released)
11 to 14 V → Below 1.5 V
A58-36 (LBL) - Body ground P - Body ground Brake fluid level warning switch input Brake fluid level warning switch OFF → ON 1.84 to 2.16 kΩ → Below 1 Ω

*1: w/ Dynamic Radar Cruise Control