Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2014.11–2015.08
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1311/11  Open in Main Relay 1 Circuit  C1312/12  Short in Main Relay 1 Circuit  


DESCRIPTION

The ABS main relay supplies power to the changeover solenoid and the linear solenoid.

The ABS main relay remains on for approximately 2 minutes after the power switch is turned off (lock) and the input of brake pedal operation signals stops, and supplies power to the system to keep it ready to operate.

DTC Code INF Code DTC Detection Condition Trouble Area
C1311/11 1 Either of the following is detected:
1.

When the power switch is on (ready):

The ABS main relay contact is not turned ON (BS terminal voltage 3.5 V or more) for 0.2 seconds or more when ABS main relay ON is requested while IG1 terminal voltage is 9.5 V or more.

2.

When the power switch is off (lock):

The ABS main relay contact is not turned ON (BS terminal voltage 3.5 V or more) for 0.2 seconds or more when ABS main relay ON is requested.


·

Open or short in ABS main relay circuit

·

Brake booster with master cylinder (Skid control ECU)


C1312/12 2 The ABS main relay contact is turned ON (BS terminal voltage 3.5 V or more) for 4.5 seconds or more when ABS main relay OFF is requested from the ECU.
·

Short in ABS main relay circuit

·

ABS main relay internal stuck

·

Brake booster with master cylinder (Skid control ECU)



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake booster with master cylinder (skid control ECU), perform initialization and calibration of the linear solenoid valve (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ABS MAIN RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Select the Active Test on the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ECB* Main Relay ABS main relay Relay ON/OFF -

*: Electronically Controlled Brake System



ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ECB* Main Relay ABS main relay / ON or OFF ON: Relay on
OFF: Relay off
-

*: Electronically Controlled Brake System

e.

Check the operating condition of the ABS main relay when operating it with the GTS.

Result:
Result Proceed to
ABS main relay in the Data List turns ON/OFF using the Active Test A
ABS main relay in the Data List does not change using the Active Test B




A

2.INSPECT SKID CONTROL ECU (BS TERMINAL)

B

4.INSPECT SKID CONTROL ECU (BI TERMINAL)
2.INSPECT SKID CONTROL ECU (BS TERMINAL)
a.
U154751E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A58 2.648,1.823 2.942,2.778 false 2.862,2.791 3.122,2.948 0.260,0.158 10 BS

Turn the power switch off (lock).


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-15 (BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the skid control ECU connector.



c.

Turn the power switch on (IG).


d.

Check if the same DTC is recorded (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs (C1311/11and C1312/12) are not output A
DTCs (C1311/11 and/or C1312/12) are output (for LHD) B
DTCs (C1311/11 and/or C1312/12) are output (for RHD) C




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

4.INSPECT SKID CONTROL ECU (BI TERMINAL)
a.
U154752E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A58 2.476,1.695 2.77,2.778 false 2.691,2.791 2.867,2.948 0.177,0.158 10 BI

Turn the power switch off (lock).


b.

Check that the ABS MAIN NO. 1 (20 A) and ABS MAIN NO. 2 (7.5 A) fuses are normal.


c.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


d.

Disconnect the skid control ECU connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-14 (BI) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)



OK

5.INSPECT SKID CONTROL ECU (BS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BI CIRCUIT)

5.INSPECT SKID CONTROL ECU (BS TERMINAL)
a.
U154751E01
0.196,0.187 0.380,0.345 0.184,0.158 10 *a 0.265,0.857 0.553,1.015 0.288,0.158 10 A58 2.648,1.823 2.942,2.778 false 2.862,2.791 3.122,2.948 0.260,0.158 10 BS

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A58-15 (BS) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU)

Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (BS CIRCUIT)