Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.03–2014.11
RM2070E _54 Brake _061923 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0301683 ELECTRONICALLY CONTROLLED BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using the GTS)


a.

Check for DTCs.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Read the DTCs following the prompts on the GTS screen. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.




b.

Clear the DTCs.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the GTS on.


iv.

Operate the GTS to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


v.

According to the display on the GTS, select the trouble code data display with the clear button.




DTC CHECK/CLEAR (When not Using the GTS)


a.

Check for DTCs.

i.
C351063E12
1.604,0.927 1.604,0.542 false 1.781,1.823 1.781,1.438 false 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 1.49,0.365 1.802,0.563 0.313,0.198 10 false CG 1.708,1.844 2.021,2.042 0.313,0.198 10 false TC

Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the power switch on (IG).


iii.

Observe the blinking pattern of the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights in order to identify the DTC.

HINT:

If no code appears, inspect the TC and CG terminal circuit, and ABS warning, brake warning / yellow (minor malfunction) and slip indicator light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Brake warning light / yellow (minor malfunction) circuit (Remains on) (Click here)
Brake warning light / yellow (minor malfunction) circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)


iv.

Count the number of blinks of the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.

HINT:
·

How to read DTCs:

Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.

·

If one code is detected:

The light repeats the same code after a pause of 4 seconds.

·

If multiple codes are detected:

The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.





vi.

After completing the check, disconnect terminals TC and CG of the DLC3 to turn off the display.

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.



b.

Clear the DTCs.

i.
C351063E12
1.604,0.927 1.604,0.542 false 1.781,1.823 1.781,1.438 false 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 1.49,0.365 1.802,0.563 0.313,0.198 10 false CG 1.708,1.844 2.021,2.042 0.313,0.198 10 false TC

Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


ii.

Turn the power switch on (IG).


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the warning light indicates a normal system code.


v.

Remove SST from the terminals of the DLC3.

HINT:

The DTCs cannot be cleared by disconnecting the auxiliary battery terminal or the ECU-IG NO. 2 fuse.





END OF DTC CHECK/CLEAR


a.

Turn the power switch on (IG).


b.

Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights go off when the power switch is turned on (ready).