Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP(for LHD) › 2012.03–2013.08
RM2070E _54 Brake _061924 BRAKE SYSTEM (OTHER) _0301697 BRAKE BOOSTER PUMP(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for LHD)  INSTALLATION  


PROCEDURE

Hide 47070 1.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.
C208396E05
3.25,1.042 3.25,0.552 3.25,0.552 2.583,0.552 false 2.833,0.813 2.833,0.552 false 2.677,0.906 2.677,0.771 2.677,0.771 2.344,0.771 false 2.427,1.063 2.427,1 2.427,1 2.104,1 false 3.167,1.198 3.219,1.198 3.219,1.198 3.219,1.458 false 2.677,2.24 2.906,2.24 false 1.26,2.865 1.26,3.031 false 1.927,1.823 1.927,2.573 false 2.469,2.021 2.469,2.365 2.469,2.365 1.927,2.365 false 1,3.896 1.198,3.896 false 0.698,3.635 0.49,3.635 false 0.854,4.177 0.854,4.344 0.854,4.344 1.219,4.344 false 2.906,1.417 2.906,1.656 false 0.51,4.042 0.396,4.042 false 2.396,0.49 2.635,0.646 0.24,0.156 10 false *1 2.135,0.688 2.323,0.844 0.188,0.156 10 false *2 3.146,1.458 3.302,1.594 0.156,0.135 10 false *2 2.844,1.656 3,1.802 0.156,0.146 10 false *3 2.938,2.167 3.135,2.323 0.198,0.156 10 false *4 1.906,0.927 2.094,1.073 0.188,0.146 10 false *3 1.188,3.042 1.365,3.188 0.177,0.146 10 false *5 0.323,3.552 0.479,3.698 0.156,0.146 10 false *5 1.854,2.594 2.021,2.74 0.167,0.146 10 false *6 1.229,3.802 1.417,3.958 0.188,0.156 10 false *7 1.219,4.25 1.406,4.396 0.188,0.146 10 false *8 0.229,3.969 0.385,4.115 0.156,0.146 10 false *4

Install the brake booster pump assembly, 2 brake traction actuator bracket bushings and 2 brake actuator case collars to the brake actuator bracket assembly with the 2 nuts.

Text in Illustration
*1 Nut
*2 Brake Actuator Case Collar
*3 Brake Traction Actuator Bracket Bushing
*4 Brake Actuator Bracket Assembly
*5 Brake Booster Pump Assembly
*6 Brake Actuator Bracket Cushion
*7 Brake Booster Pump Collar
*8 Brake Booster Pump Bushing

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:
·

Do not drop the brake booster pump assembly when carrying it.

·

Do not carry the brake booster pump assembly by the connector.

·

Confirm that the 2 brake actuator bracket cushions are on the brake actuator bracket assembly, and each brake booster pump bushing and brake booster pump collar are on the brake booster pump assembly when installing the brake booster pump assembly to the brake actuator bracket assembly.

·

Do not remove the hole plugs before installing a new brake booster pump assembly because the brake booster pump assembly is filled with brake fluid.




Hide 2.INSTALL BRAKE BOOSTER PUMP ASSEMBLY WITH BRACKET

a.
C210144E04
2.198,2.792 1.958,2.792 false 1.625,1.323 1.865,1.615 0.24,0.292 10 true 1 1.458,0.99 1.656,1.198 0.198,0.208 10 true 2 1.177,0.417 1.406,0.563 0.229,0.146 10 false 3 2.229,2.708 2.625,2.958 0.396,0.25 10 true SST

Using SST, install the brake booster pump assembly with bracket with the 3 nuts.

SST
09961-00950  

Torque:
without SST : 19 N*m (194 kgf*cm, 14 ft.*lbf)
with SST : 12 N*m (121 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Use a torque wrench with a fulcrum length of 250 mm (9.84 in.).

·

Tighten the 3 nuts in the order shown in the illustration.

·

Do not damage the fuel line, the brake lines or wire harness.

·

Use the formula to calculate special torque values for situations where SST is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




b.
U154773E04
2.625,0.167 2.823,0.167 false 1.188,0.875 1.188,0.333 1.188,0.333 1.052,0.333 false 1.323,1.063 1.323,1.198 false 2.844,0.083 3.115,0.344 0.271,0.26 10 false *1 0.875,0.24 1.177,0.479 0.302,0.24 10 false *2 1.25,1.208 1.458,1.417 0.208,0.208 10 true *2 2.344,1.729 2.677,1.927 0.333,0.198 10 false *3

Install the wire harness clamp, 2 fuel lines and front No. 4 brake tube to the brake actuator bracket assembly.

Text in Illustration
*1 Wire Harness Clamp
*2 Fuel Line
*3 Front No. 4 Brake Tube

NOTICE:

Do not damage the fuel line, the brake lines and wire harness.



c.
C220937E06
1.833,0.854 2.292,0.854 false 1.604,1.271 2.063,1.271 false 1.604,0.354 1.073,0.354 false 0.792,0.781 0.49,0.781 false 2.302,0.792 2.5,0.958 0.198,0.167 10 true *1 0.906,0.281 1.063,0.427 0.156,0.146 10 false *2 2.063,1.198 2.24,1.385 0.177,0.188 10 true *3 0.344,0.698 0.5,0.844 0.156,0.146 10 true *1

Install the No. 1 brake tube clamp bracket to the brake booster pump assembly with the bolt.

Text in Illustration
*1 No. 1 Brake Tube Clamp Bracket
*2 No. 7 Brake Tube Clamp
*3 Front No. 1 Brake Tube

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


d.

Using a union nut wrench, connect the front No. 1 brake tube to the brake booster pump assembly.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



e.

Install the No. 7 brake tube clamp to the No. 1 brake tube clamp bracket with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


f.

Install the wire harness clamp to the brake actuator bracket assembly.


g.

Connect the 2 connectors to the brake booster pump assembly.


Hide 51201 3.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 47210L 4.INSTALL BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY