Home › Brake › BRAKE (FRONT) › FRONT BRAKE › 2014.11–2016.05
RM2070E _54 Brake _061925 BRAKE (FRONT) _0301701 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.

·

While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or the door courtesy switch is turned on. Therefore, even if only brake pads are to be removed and installed, be sure to perform the Disable Brake Control procedure and disconnect the cable from the negative (-) terminal of the auxiliary battery before beginning work.



HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.REMOVE FRONT WHEEL

Hide 4.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47313J 5.SEPARATE FRONT FLEXIBLE HOSE

a.
C210915

Remove the union bolt and gasket, and separate the front flexible hose from the disc brake cylinder assembly.


Hide 6.REMOVE DISC BRAKE CYLINDER ASSEMBLY

a.
C236567E01
2.894,2.735 3.050,2.889 0.156,0.154 10 *a 2.087,2.481 2.245,2.623 0.158,0.142 10 *b

Hold the front disc brake cylinder slide pin, and remove the 2 bolts and disc brake cylinder assembly.

Text in Illustration
*a Hold
*b Turn


Hide 04465 7.REMOVE FRONT DISC BRAKE PAD

a.

Remove the 2 front disc brake pads from the front disc brake cylinder mounting.


Hide 8.REMOVE FRONT ANTI-SQUEAL SHIM KIT

a.
C263977E01
0.664,2.03 0.834,2.196 0.170,0.166 10 *1 0.153,1.79 0.307,1.932 0.154,0.142 10 *2 2.586,0.748 2.752,0.890 0.166,0.142 10 *3 2.369,2.897 2.539,3.063 0.170,0.166 10 *1 2.908,3.039 3.062,3.182 0.154,0.142 10 *2 0.24,1.499 0.24,1.787 false 0.765,1.74 0.765,2.027 false 2.453,2.606 2.453,2.893 false 2.995,2.922 2.995,3.04 false 1.603,1.103 1.603,0.837 1.603,0.837 2.586,0.837 false 2.221,1.442 2.221,0.837 false

Remove the front No. 1 anti-squeal shim and front No. 2 anti-squeal shim from each front disc brake pad.

Text in Illustration
*1 Front No. 1 Anti-squeal Shim
*2 Front No. 2 Anti-squeal Shim
*3 Pad Wear Indicator Plate


b.

Remove the pad wear indicator plate from each front disc brake pad.


Hide 04947 9.REMOVE FRONT DISC BRAKE FITTING KIT

a.
C210920E05
2.073,0.625 2.521,0.625 false 2.083,1.698 2.521,1.698 false 1.49,0.677 1.042,0.677 false 1.49,1.646 1.042,1.646 false 0.854,1.573 1.031,1.74 0.177,0.167 10 true *1 2.531,0.542 2.708,0.698 0.177,0.156 10 false *1 0.865,0.583 1.042,0.74 0.177,0.156 10 true *2 2.552,1.615 2.729,1.771 0.177,0.156 10 false *2

Remove the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates from the front disc brake cylinder mounting.

Text in Illustration
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate

NOTICE:

Each front disc brake pad support plate has a different shape. Be sure to put an identification mark on each front disc brake pad support plate so that it can be reinstalled to its original position.



Hide 47715A 10.REMOVE FRONT NO. 1 DISC BRAKE CYLINDER SLIDE PIN

a.
C210921

Remove the front No. 1 disc brake cylinder slide pin from the front disc brake cylinder mounting.


Hide 47715D 11.REMOVE FRONT NO. 2 DISC BRAKE CYLINDER SLIDE PIN

a.
C210922

Remove the front No. 2 disc brake cylinder slide pin from the front disc brake cylinder mounting.


Hide 12.REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSHING

a.
C210924E17
2.552,0.909 2.715,1.072 0.163,0.163 10 *1 2.332,1.4 2.332,0.996 2.332,0.996 2.545,0.996 false

Using a screwdriver with its tip wrapped with vinyl tape, remove the front disc brake cylinder slide bushing from the front No. 2 disc brake cylinder slide pin.

Text in Illustration
*1 Vinyl Tape

NOTICE:

Do not damage the front No. 2 disc brake cylinder slide pin.



Hide 13.REMOVE FRONT DISC BRAKE BUSHING DUST BOOT

a.
C210923

Remove the 2 front disc brake bushing dust boots from the front disc brake cylinder mounting.


Hide 14.REMOVE FRONT DISC BRAKE CYLINDER MOUNTING

a.
C210925

Remove the 2 bolts and front disc brake cylinder mounting from the steering knuckle.


Hide 43512 15.REMOVE FRONT DISC

a.
C210926E01
1.938,1.084 2.549,1.1 2.549,1.1 1.966,1.149 false 2.57,1.01 2.734,1.160 0.164,0.150 10 *a

Remove the front disc.

Text in Illustration
*a Matchmark

HINT:

Put matchmarks on the disc and the axle hub.