Home › Brake › BRAKE (REAR) › REAR BRAKE FLEXIBLE HOSE › 2014.11–2016.05
RM2070E _54 Brake _061926 BRAKE (REAR) _0301704 REAR BRAKE FLEXIBLE HOSE A

BRAKE (REAR)  REAR BRAKE FLEXIBLE HOSE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the flexible hoses.

·

If the hoses are to be reused, connect them after checking the identification marks placed when each hose was disconnected.



HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 47316A 1.INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for LH Side)

a.

Install the rear brake tube flexible hose with the bolt and a new clip.

C236535E03
5.885,1.813 6.083,1.813 false 6.115,1.729 6.292,1.906 0.177,0.177 10 true *a

Text in Illustration
*a Identification Mark - -
V100136

Inside of the Vehicle - -

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Install the clip as far as it will go.

·

When installing the rear brake tube flexible hose, face the identification mark to the inside of the vehicle and minimize twisting of the hose.




b.
C236554

Using a union nut wrench, connect the 2 brake lines to the rear brake tube flexible hose.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47316A 2.INSTALL REAR BRAKE TUBE FLEXIBLE HOSE (for RH Side)

a.

Install the rear brake tube flexible hose with 2 new clips.

C236540E03
1.219,1.823 1.021,1.823 false 0.875,1.729 1.042,1.885 0.167,0.156 10 true *a

Text in Illustration
*a Identification Mark - -
V100136

Inside of the Vehicle - -

NOTICE:
·

Install the clip as far as it will go.

·

When installing the rear brake tube flexible hose, face the identification mark to the inside of the vehicle and minimize twisting of the hose.




b.
C236555

Using a union nut wrench, connect the 2 brake lines to the rear brake tube flexible hose.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 47319F 3.INSTALL REAR FLEXIBLE HOSE

a.
C244061

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
33 N*m (340 kgf*cm, 25 ft.*lbf)


b.
C244063

Install a new clip.

NOTICE:

Install the clip as far as it will go.



c.
C244062

Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not bend or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line from the connecting points.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 4.FILL RESERVOIR WITH BRAKE FLUID

Hide 5.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 7.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)