Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  TERMINALS OF ECU  


CHECK POWER STEERING ECU ASSEMBLY


C370350E02
2.115,0.833 2.531,1.083 0.417,0.25 3.375,0.771 3.792,1.021 0.417,0.25 3.823,0.771 4.24,1.021 0.417,0.25 4.271,0.771 4.688,1.021 0.417,0.25 5.083,0.417 5.5,0.667 0.417,0.25 0.25,0.167 0.563,0.365 0.313,0.198 10 false *a 2.208,0.875 2.521,1.073 0.313,0.198 10 false z16 3.479,0.802 3.792,1 0.313,0.198 10 false z15 3.917,0.813 4.229,1.01 0.313,0.198 10 false z14 4.344,0.813 4.656,1.01 0.313,0.198 10 false L54 5.156,0.458 5.469,0.656 0.313,0.198 10 false A27

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

HINT:

As connector z16 uses a lock lever, each terminal cannot be checked while the connector is still connected to the power steering ECU assembly.


Terminal No. (Symbol) Wiring Color Terminal Description
z16-1 (V) W V phase motor output
z16-2 (U) B U phase motor output
z16-3 (W) R W phase motor output

a.

Measure the voltage and resistance according to the value(s) in the table below.

NOTICE:

When the EPS warning light is illuminated during a malfunction, the fail-safe function may cause the voltage of the power steering ECU assembly terminals to become 0 V.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A27-1 (PIG) - Body ground W - Body ground Power source Always 9 to 16 V
A27-2 (PGND) - Body ground W-B - Body ground Power ground Always Below 1 Ω
L54-1 (CANH) - L54-7 (CANL) R - W CAN communication line Power switch off 54 to 69 Ω
L54-6 (IG) - Body ground L - Body ground IG power source Power switch on (IG) 9 to 16 V
z15-1 (RZV) - A27-2 (PGND) R - W-B Rotation angle sensor excitation output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
z15-3 (RZG) - A27-2 (PGND) B - W-B Rotation angle sensor excitation circuit GND Always Below 1 Ω
z15-5 (RZCS) - A27-2 (PGND) L - W-B Rotation angle sensor COS aspect output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
z15-6 (RZSN) - A27-2 (PGND) Y - W-B Rotation angle sensor SIN aspect output signal Power switch on (READY)
Steering wheel turned
0.68 to 4.42 V
z14-5 (TRQ1) - z14-8 (TRQG) W - B Torque sensor signal Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel turned being to right with vehicle stopped
2.5 to 3.8 V
Power switch on (READY)
Steering wheel being turned to left with vehicle stopped
1.2 to 2.5 V
z14-6 (TRQV) - z14-8 (TRQG) R - B Torque sensor voltage source Power switch on (READY) 4.5 to 5.5 V
z14-7 (TRQ2) - z14-8 (TRQG) Y - B Torque sensor signal Power switch on (READY)
Steering wheel not being turned (without load)
2.3 to 2.7 V
Power switch on (READY)
Steering wheel being turned to right with vehicle stopped
1.2 to 2.5 V
Power switch on (READY)
Steering wheel being turned to left with vehicle stopped
2.5 to 3.8 V
z14-8 (TRQG) - Body ground B - Body ground Torque sensor ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.