Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM2070E _55 Steering _061928 POWER ASSIST SYSTEMS _0301712 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  FREEZE FRAME DATA  


FREEZE FRAME DATA


NOTICE:
·

It is difficult to show the specified values (judgment values) clearly because freeze frame data values change significantly due to differences in measurement conditions, surroundings, or vehicle conditions. For this reason, there may be a problem even when the values are within specifications.

·

Turn the power switch on (IG) and park the vehicle on level ground. Check the freeze frame data by using the GTS.



a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Check the freeze frame data on the GTS.

EMPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Meter Vehicle Velocity Vehicle speed from meter/
Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph)
0 km/h (0 mph) Power switch on (READY) and vehicle stopped
No significant fluctuation Power switch on (READY) and vehicle driven at a constant speed
Motor Actual Current Amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
- The value rises in left turn
- The value descends in right turn
Power switch on (READY) and steering wheel being turned
Command Value Current Demanded amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort
- The value rises in left turn
- The value descends in right turn
Power switch on (READY) and steering wheel being turned
Steering Angle Velocity Steering angle speed/
Min.: -32768 deg/s
Max.: 32767 deg/s
Value changes in proportion to steering speed
- The value rises in left turn
- The value descends in right turn
Power switch on (READY) and steering wheel being turned
Thermistor Temperature ECU substrate temperature/
Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F)
-50°C to 150°C (-58°F to 302°F) Power switch on (READY)
PIG Power Supply Power source voltage to active motor/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Always
IG Power Supply ECU power source voltage/
Min.: 0.0000 V
Max.: 20.1531 V
9 to 16 V Power switch on (IG)
Steering Wheel Torque Steering wheel torque/
Min.: -327.68 Nm
Max.: 7.00 Nm
Value changes in proportion to steering effort
- The value rises in left turn
- The value descends in right turn
Power switch on (READY) and steering wheel being turned
Motor Rotation Angle Motor rotation angle/
Min.: 0.000 deg
Max.: 1441.770 deg
During steering operation, motor rotation angle value changes from 0 to 360° Power switch on (READY) and steering wheel being turned
Command Val Current 2 Demanded amount of current to motor/
Min.: -327.68 A
Max.: 327.67 A
Value changes in proportion to steering effort Power switch on (READY) and steering wheel being turned
PIG2 Voltage Coil rear pressurization voltage/
Min.: 0.000 V
Max.: 45.955V
9 to 16 V Power switch on (READY)
Motor Voltage Motor power supply voltage/
Min.: 0.000 V
Max.: 45.955 V
Approximately 30 V Power switch on (READY) and steering wheel not being turned
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned
Motor Terminal Volt (U) Motor terminal voltage (U phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned
Motor Terminal Volt (V) Motor terminal voltage (V phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned
Motor Terminal Volt (W) Motor terminal voltage (W phase)/
Min.: 0.000 V
Max.: 98.000 V
Value changes within 4 to 35 V range Power switch on (READY) and steering wheel being turned
Torque Sensor 1 Output Torque sensor voltage/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (READY) and steering wheel not turned (without load)
2.5 to 3.8 V Power switch on (READY) and steering wheel being turned to the right with vehicle stopped
1.2 to 2.5 V Power switch on (READY) and steering wheel being turned to the left with vehicle stopped
Torque Sensor 2 Output Torque sensor voltage/
Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V Power switch on (READY) and steering wheel not turned (without load)
1.2 to 2.5 V Power switch on (READY) and steering wheel being turned to the right with vehicle stopped
2.5 to 3.8 V Power switch on (READY) and steering wheel being turned to the left with vehicle stopped
TRQ1 Zero Point Value Torque sensor voltage/
Min.: 0.0000 V
Max.: 4.9725 V
Values differ depending on vehicle Power switch on (READY) and steering wheel not being turned
TRQ2 Zero Point Value Torque sensor voltage/
Min.: 0.0000 V
Max.:4.9725 V
Values differ depending on vehicle Power switch on (READY) and steering wheel not being turned
Ready Status Ready status/
OFF or Ready
OFF or Ready -