84247A
1.INSPECT STEERING PAD SWITCH LH
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (AU1) - 1 (EAU) | No switch pushed | 95 to 105 kΩ |
| Seek+ switch pushed | Below 2.5 Ω | |
| Seek- switch pushed | 323 to 335 Ω | |
| Volume+ switch pushed | 980 to 1020 Ω | |
| Volume- switch pushed | 3048 to 3172 Ω | |
| 3 (AU2) - 1 (EAU) | No switch pushed | 95 to 105 kΩ |
| MODE switch pushed | Below 2.5 Ω | |
| On hook switch pushed | 323 to 335 Ω | |
| Off hook switch pushed | 980 to 1020 Ω | |
| Voice switch pushed | 3048 to 3172 Ω |
If the result is not as specified, replace the steering pad switch LH.
| *a | Component without harness connected
(Steering Pad Switch LH) |
*b | Volume+ |
| *c | Volume- | *d | MODE |
| *e | Seek+ | *f | Seek- |
| *g | Voice | *h | On hook |
| *i | Off hook | - | - |
Check the illumination.
Connect an auxiliary battery positive (+) lead to terminal 2 (IL+2) and a negative (-) lead to terminal 1 (EAU) of the steering pad switch LH connector.
Check that the switch illumination comes on.
Steering pad switch illumination comes on.
If the result is not as specified, replace the steering pad switch LH.
| *a | Component without harness connected
(Steering Pad Switch LH) |
- | - |
84244B
2.INSPECT STEERING PAD SWITCH RH (w/o Multi-information Display)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-1 (HO) - Terminal-A | Always | Below 1 Ω |
| z9-2 (TRIP) - z9-8 (EAU) | No switch pushed | 1 MΩ or higher |
| TRIP switch pushed | Below 2.5 Ω | |
| z9-3 (AC1) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| R/F switch pushed | 323 to 335 Ω | |
| TEMP+ switch pushed | 980 to 1020 Ω | |
| TEMP- switch pushed | 3048 to 3172 Ω | |
| z9-7 (DISP) - z9-8 (EAU) | No switch pushed | 1 MΩ or higher |
| DISP switch pushed | Below 2.5 Ω | |
| SR2-2 (IL+2) - z9-5 (IL+2) | Always | Below 1 Ω |
| SR2-4 (AU1) - z9-10 (AU1) | Always | Below 1 Ω |
| SR2-3 (AU2) - z9-9 (AU2) | Always | Below 1 Ω |
| SR2-1 (EAU) - z9-8 (EAU) | Always | Below 1 Ω |
If the result is not as specified, replace the steering pad switch RH.
| *a | Component without harness connected
(Steering Pad Switch RH) |
*b | TEMP+ |
| *c | TEMP- | *d | DISP |
| *e | R/F | *f | TRIP |
| *g | Terminal-A | - | - |
Check the illumination.
Connect an auxiliary battery positive (+) lead to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch RH connector.
Check that the switch illumination comes on.
Steering pad switch illumination comes on.
If the result is not as specified, replace the steering pad switch RH.
| *a | Component without harness connected
(Steering Pad Switch RH) |
- | - |
84244B
3.INSPECT STEERING PAD SWITCH RH (w/ Multi-information Display)
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z9-1 (HO) - Terminal-A | Always | Below 1 Ω |
| z9-2 (TRIP) - z9-8 (EAU) | No switch pushed | 1 MΩ or higher |
| TRIP switch pushed | Below 2.5 Ω | |
| z9-3 (+DP2) - z9-8 (EAU) | No switch pushed | 95 to 105 kΩ |
| Left switch pushed | Below 2.5 Ω | |
| Up switch pushed | 323 to 335 Ω | |
| Down switch pushed | 980 to 1020 Ω | |
| Right switch pushed | 3048 to 3172 Ω | |
| z9-4 (DIST) - z9-6 (ECC)* | No switch pushed | 1 MΩ or higher |
| Distance control switch pushed | Below 2.5 Ω | |
| z9-7 (+DP) - z9-8 (EAU) | No switch pushed | 1 MΩ or higher |
| Enter switch pushed | Below 2.5 Ω | |
| Back switch pushed | 980 to 1020 Ω | |
| SR2-2 (IL+2) - z9-5 (IL+2) | Always | Below 1 Ω |
| SR2-4 (AU1) - z9-10 (AU1) | Always | Below 1 Ω |
| SR2-3 (AU2) - z9-9 (AU2) | Always | Below 1 Ω |
| SR2-1 (EAU) - z9-8 (EAU) | Always | Below 1 Ω |
*: w/ Distance Control Switch
If the result is not as specified, replace the steering pad switch RH.
| *A | w/ Distance Control Switch | - | - |
| *a | Component without harness connected
(Steering Pad Switch RH) |
*b | Up |
| *c | Down | *d | Left |
| *e | Right | *f | Enter |
| *g | Back | *h | TRIP |
| *i | Distance control | *j | Terminal-A |
Check the illumination.
Connect an auxiliary battery positive (+) lead to terminal 5 (IL+2) and a negative (-) lead to terminal 8 (EAU) of the steering pad switch RH connector.
Check that the switch illumination comes on.
Steering pad switch illumination comes on.
If the result is not as specified, replace the steering pad switch RH.
| *a | Component without harness connected
(Steering Pad Switch RH) |
- | - |