Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E287097E76
0.438,0.792 1.802,0.969 1.365,0.177 10 false from Auxiliary Battery 0.354,1.563 2.188,1.74 1.833,0.177 10 false from ACC NO. 1 Relay 0.427,2.375 1.802,2.552 1.375,0.177 10 false from IG1 NO. 2 Relay 5.823,0.792 6.104,0.969 0.281,0.177 10 false +B1 5.833,1.573 6.219,1.75 0.385,0.177 10 false ACC1 5.813,2.375 5.979,2.552 0.167,0.177 10 false IG 5.823,3.156 6.229,3.333 0.406,0.177 10 false GND1 5.406,0.781 5.75,0.958 0.344,0.177 10 false L167 5.448,2.365 5.792,2.542 0.344,0.177 10 false L35 5.51,0.583 5.667,0.76 0.156,0.177 10 false 4 5.51,1.385 5.667,1.563 0.156,0.177 10 false 3 5.51,2.167 5.667,2.344 0.156,0.177 10 false 1 5.51,2.948 5.667,3.125 0.156,0.177 10 false 7 3.323,0.948 4.177,1.125 0.854,0.177 10 false RAD NO. 1 3.354,1.74 4.063,1.917 0.708,0.177 10 false ECU-ACC 3.26,2.531 4.365,2.708 1.104,0.177 10 false ECU-IG NO. 2 5.229,3.615 6.917,4.104 1.688,0.49 10 false Radio and Display Receiver Assembly 5.406,1.573 5.75,1.75 0.344,0.177 10 false L167 5.417,3.156 5.76,3.333 0.344,0.177 10 false L167

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the L167 and L35 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L167-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L167-4 (+B1) - L167-7 (GND1) Power switch off 11 to 14 V
L167-3 (ACC1) - L167-7 (GND1) Power switch on (ACC) 11 to 14 V
L35-1 (IG) - L167-7 (GND1) Power switch on (IG) 11 to 14 V




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR