Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transfers the switch signals using the AVC-LAN.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E226159E28
0.406,2.132 2.829,2.306 2.424,0.174 10 Stereo Component Amplifier Assembly 4.422,1.952 4.772,2.099 0.350,0.147 10 L35 4.422,2.132 6.795,2.299 2.373,0.167 10 Radio and Display Receiver Assembly 5.113,1.485 5.492,1.632 0.378,0.147 10 TX1- 5.113,0.672 5.533,0.847 0.420,0.174 10 TX1+ 4.894,1.392 5.074,1.538 0.180,0.147 10 8 4.894,0.579 4.999,0.753 0.105,0.174 10 7 1.682,1.504 2.015,1.650 0.334,0.147 10 ATX- 1.682,0.691 2.054,0.865 0.372,0.174 10 ATX+ 2.19,1.387 2.369,1.534 0.179,0.147 10 7 2.171,0.574 2.368,0.749 0.198,0.174 10 8 0.406,1.952 0.756,2.099 0.350,0.147 10 L31

CAUTION / NOTICE / HINT

HINT:

The radio and display receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the L35 radio and display receiver assembly connectors.


b.
U191284E01
1.588,0.453 1.838,0.607 0.250,0.154 10 L35 0.133,0.086 0.303,0.261 0.170,0.174 10 *a 1.365,1.73 1.657,1.203 false 2.086,1.73 1.794,1.203 false 1.15,1.749 1.475,1.924 0.325,0.174 10 TX1- 1.895,1.749 2.250,1.924 0.355,0.174 10 TX1+

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-7 (TX1+) - L35-8 (TX1-) Always 60 to 80 Ω


Text in Illustration
*a Component without harness connected
(Radio and Display Receiver Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-7 (TX1+) - L31-8 (ATX+) Always Below 1 Ω
L35-8 (TX1-) - L31-7 (ATX-) Always Below 1 Ω
L35-7 (TX1+) - Body ground Always 10 kΩ or higher
L35-8 (TX1-) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal operation, the slave unit is defective and should be replaced.



OK:

Master unit returns to normal operation.




OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY