Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E236970E08
0.973,0.634 1.270,0.952 0.297,0.319 10 SLD 1.313,0.549 1.498,0.717 0.186,0.168 10 6 1.11,1.1 1.271,1.419 0.161,0.319 10 L- 1.313,1.015 1.498,1.183 0.186,0.168 10 2 1.092,1.579 1.271,1.898 0.179,0.319 10 L+ 1.313,1.495 1.498,1.662 0.186,0.168 10 3 1.096,2.049 1.271,2.368 0.175,0.319 10 R- 1.313,1.965 1.498,2.133 0.186,0.168 10 4 1.069,2.528 1.271,2.847 0.201,0.319 10 R+ 3.239,2.813 3.896,3.132 0.657,0.319 10 (Shielded) 0.277,3.084 1.490,3.402 1.213,0.319 10 Stereo Component Amplifier Assembly 1.313,2.444 1.498,2.612 0.186,0.168 10 5 5.91,1.1 6.165,1.419 0.255,0.319 10 FL- 5.772,1.015 5.868,1.183 0.095,0.168 10 6 5.91,1.579 6.186,1.898 0.276,0.319 10 FL+ 5.772,1.495 5.878,1.662 0.105,0.168 10 2 5.91,2.049 6.182,2.368 0.272,0.319 10 FR- 5.772,1.965 5.875,2.133 0.102,0.168 10 5 5.91,2.528 6.222,2.847 0.312,0.319 10 FR+ 5.772,2.444 5.878,2.612 0.105,0.168 10 1 0.277,2.931 0.699,3.099 0.422,0.168 10 L31 5.681,3.096 6.894,3.414 1.213,0.319 10 Radio and Display Receiver Assembly 5.681,2.943 6.057,3.111 0.376,0.168 10 L36

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L36 radio and display receiver assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-5 (R+) - L36-1 (FR+) Always Below 1 Ω
L31-4 (R-) - L36-5 (FR-) Always Below 1 Ω
L31-3 (L+) - L36-2 (FL+) Always Below 1 Ω
L31-2 (L-) - L36-6 (FL-) Always Below 1 Ω
L31-6 (SLD) - Body ground Always 10 kΩ or higher
L31-5 (R+) - Body ground Always 10 kΩ or higher
L31-4 (R-) - Body ground Always 10 kΩ or higher
L31-3 (L+) - Body ground Always 10 kΩ or higher
L31-2 (L-) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR