Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Because of that, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E226158E47
1.212,1.108 1.653,1.271 0.441,0.163 10 MUTE 5.521,1.108 5.940,1.271 0.420,0.163 10 MUT2 1.738,0.978 1.880,1.117 0.142,0.139 10 1 5.289,0.978 5.466,1.117 0.177,0.139 10 20 0.624,1.969 1.106,2.125 0.482,0.156 10 L31 0.624,2.117 1.863,2.453 1.239,0.336 10 Stereo Component Amplifier Assembly 5.268,1.969 5.667,2.153 0.399,0.184 10 L35 5.268,2.117 6.584,2.453 1.316,0.336 10 Radio and Display Receiver Assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U191322E01
0.207,0.166 0.366,0.329 0.159,0.163 10 *a 1.577,0.851 1.826,1.003 0.249,0.152 10 L31 2.699,2.413 3.129,2.576 0.430,0.163 10 MUTE 2.399,1.887 2.861,2.381 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L31-1 (MUTE) - Body ground Power switch on (ACC), audio system playing
→ Changing modes
Above 3.5 V
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L35-20 (MUT2) - L31-1 (MUTE) Always Below 1 Ω
L35-20 (MUT2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Reconnect the L31 stereo component amplifier assembly connector.


b.
U191285E01
1.598,0.849 1.847,1.005 0.249,0.156 10 L35 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 1.054,2.735 1.450,2.890 0.396,0.156 10 MUT2 1.55,2.222 1.371,2.72 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L35-20 (MUT2) - Body ground Power switch on (ACC), audio system is playing Above 3.5 V


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY