Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2012.03–2013.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter  


DESCRIPTION

for Automatic Sound Levelizer (ASL) (for 6 Speakers):

This circuit is necessary for the Automatic Sound Levelizer (ASL) built into the radio and display receiver assembly.

The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the meter circuit plate.


for "Bluetooth":

Vehicle speed signals are received from the meter circuit plate and used to cancel "Bluetooth" function operation.

The radio and display receiver assembly recognizes that the vehicle is being to driven and makes it impossible to connect or register a "Bluetooth" device while driving.


HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the meter circuit plate. The signal is changed to a pulse signal at the transistor in the meter circuit plate. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E251604E04
0.635,1.521 1.76,1.667 1.125,0.146 10 false Skid Control ECU 1.438,0.51 1.729,0.656 0.292,0.146 10 false SP1 0.635,1.365 0.958,1.542 0.323,0.177 10 false A58 1.792,0.51 1.979,0.656 0.188,0.146 10 false 11 3.052,7.438 4.271,7.604 1.219,0.167 10 false Junction Connector 0.563,2.969 1.896,3.344 1.333,0.375 10 false Power Management Control ECU 0.563,2.813 0.854,2.979 0.292,0.167 10 false L5 0.104,7.208 0.365,7.375 0.26,0.167 10 false A48 0.104,7.365 2.417,7.542 2.313,0.177 10 false Headlight Leveling ECU Assembly*4 1.333,6.927 1.75,7.083 0.417,0.156 10 false SPDR 1.385,2.406 1.781,2.563 0.396,0.156 10 false SPDI 1.792,2.406 1.969,2.563 0.177,0.156 10 false 14 1.792,6.917 1.979,7.073 0.188,0.156 10 false 16 3.917,2.406 4.354,2.573 0.438,0.167 10 false 31*2 3.917,2.25 4.354,2.417 0.438,0.167 10 false 32*1 2.875,2.406 3.094,2.573 0.219,0.167 10 false 22 1.792,4.24 1.99,4.406 0.198,0.167 10 false 24 5.292,6.917 5.51,7.083 0.219,0.167 10 false 11 3.917,4.24 4.302,4.406 0.385,0.167 10 false 12*2 4,4.083 4.385,4.25 0.385,0.167 10 false 3*1 2.729,4.24 3.115,4.406 0.385,0.167 10 false 21*2 2.729,4.083 3.115,4.25 0.385,0.167 10 false 12*1 3.917,6.917 4.302,7.083 0.385,0.167 10 false 11*2 3.917,6.75 4.302,6.917 0.385,0.167 10 false 21*1 2.729,6.917 3.115,7.083 0.385,0.167 10 false 32*2 2.729,6.75 3.115,6.917 0.385,0.167 10 false 31*1 5.302,0.51 5.604,0.656 0.302,0.146 10 false 16 5.302,2.406 5.573,2.552 0.271,0.146 10 false 15 5.552,0.604 5.75,0.75 0.198,0.146 10 false SI 5.552,2.51 5.75,2.656 0.198,0.146 10 false +S 4.99,2.771 5.323,2.917 0.333,0.146 10 false L27 4.99,2.927 7.104,3.313 2.115,0.385 10 false Combination Meter Sub-assembly (Meter Circuit Plate) 0.448,4.656 0.813,4.813 0.365,0.156 10 false L146 0.448,4.813 1.979,5.323 1.531,0.51 10 false Windshield Wiper Relay Assembly*3 4.979,6.021 7.052,6.313 2.073,0.292 10 false Navigation ECU Sub-assembly*6 0.563,7.917 1.375,8.094 0.813,0.177 10 false *1: for LHD 1.75,7.917 2.563,8.094 0.813,0.177 10 false *2: for RHD 2.927,7.917 4.698,8.094 1.771,0.177 10 false *3: w/ Auto Wiper System 5,7.917 6.344,8.094 1.344,0.177 10 false *4: w/ LED Headlight 0.563,8.313 2.302,8.49 1.74,0.177 10 false *5: w/o Navigation System 2.927,8.313 4.531,8.49 1.604,0.177 10 false *6: w/ Navigation System 1.448,4.24 1.771,4.385 0.323,0.146 10 false SPD 5.542,6.917 5.865,7.063 0.323,0.146 10 false SPD 4.979,5.865 5.25,6.01 0.271,0.146 10 false L38 4.49,7.219 4.76,7.375 0.271,0.156 10 false L31 4.552,4.51 4.854,4.667 0.302,0.156 10 false L35 4.49,7.375 7.125,7.552 2.635,0.177 10 false Stereo Component Amplifier Assembly*7 4.552,4.667 7.083,4.844 2.531,0.177 10 false Radio and Display Receiver Assembly*5 2.76,7.438 3.073,7.604 0.313,0.167 10 false L70 5.552,4.24 5.865,4.406 0.313,0.167 10 false SPD 5.313,4.24 5.49,4.406 0.177,0.167 10 false 17 5.552,5.583 5.865,5.75 0.313,0.167 10 false SPD 5.313,5.583 5.49,5.75 0.177,0.167 10 false 17 5,8.313 6.708,8.49 1.708,0.177 10 false *7: for 8 Speakers

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E227878

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal Check Mode in Operation Check (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>OPERATION CHECK).


b.

While driving the vehicle, compare the "SPEED" indicator to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The meter circuit plate receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "Vehicle Signal Check Mode" screen is almost the same as the actual vehicle speed measured using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
2.INSPECT METER CIRCUIT PLATE (OUTPUT WAVEFORM)
a.
E362569E01
1.042,1.99 1.26,1.333 false 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 1.583,0.385 1.896,0.583 0.313,0.198 10 false L27 2.792,3.594 3.177,3.802 0.385,0.208 10 false GND 1.083,3.875 1.396,4.073 0.313,0.198 10 false (A) 0.906,2.021 1.219,2.219 0.313,0.198 10 false +S

Check the output waveform.

i.

Remove the meter circuit plate with the connector still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L27-15 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Meter Circuit Plate)




OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.

Check the input waveform.

E265791E06
1.646,0.271 2.063,0.531 0.417,0.26 2.594,1.833 2.396,1.396 false 0.177,0.146 0.49,0.344 0.313,0.198 10 false *a 1.729,0.323 2.042,0.521 0.313,0.198 10 false L35 2.5,1.854 2.813,2.052 0.313,0.198 10 false SPD 4.75,1.708 5.063,1.906 0.313,0.198 10 false (A) 6.167,1.469 6.594,1.688 0.427,0.219 10 false GND

i.

Remove the radio and display receiver assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal L35-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L35-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Radio and Display Receiver Assembly)




OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L35 radio and display receiver assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L35-17 (SPD) - L70-3 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L35-17 (SPD) - L70-12 Always Below 1 Ω




OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - JUNCTION CONNECTOR)