When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.
When a large amount of data is in a USB device, it may take a while to begin play.
When using a USB device, files that are protected by copyright cannot be played.
When files are not played in the sorted order, perform the following procedure before inspection.
Add numbers in front of the file names.
Put the files in a folder and copy the folder data to the USB device.
Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.
Check if playable files are present on the USB device or "iPod".
Refer to System Description for playable files (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).
Check if the USB device is a compatible format or "iPod" is a compatible version.
Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).
| Result | Proceed to |
|---|---|
| No playable files exist, or incompatible device format or version | A |
| Playable files exist, and compatible device format or version | B |
A
B
Disconnect the L135 radio and display receiver assembly connector.
Disconnect the L13 No. 1 stereo jack adapter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L13-1 (UPI) - L135-1 (UPO) | Always | Below 1 Ω |
| L13-2 (UDO-) - L135-2 (UDO-) | Always | Below 1 Ω |
| L13-3 (UDO+) - L135-3 (UDO+) | Always | Below 1 Ω |
| L13-4 (UJSG) - L135-4 (UESG) | Always | Below 1 Ω |
| L13-5 (UJSS) - L135-5 (USG1) | Always | Below 1 Ω |
| L13-1 (UPI) - Body ground | Always | 10 kΩ or higher |
| L13-2 (UDO-) - Body ground | Always | 10 kΩ or higher |
| L13-3 (UDO+) - Body ground | Always | 10 kΩ or higher |
| L13-4 (UJSG) - Body ground | Always | 10 kΩ or higher |
| L13-5 (UJSS) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly) |
OK
NG
Reconnect the L135 radio and display receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L13-1 (UPI) - L13-4 (UJSG) | Power switch on (ACC) | 5 V |
| *a | Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly) |
OK
NG
Delete all files in the USB device or "iPod" and format/restore it.
Save the data again and check if it can be played on the in-vehicle device.
Formatting a USB device or restoring an "iPod" erases all music on the device. Ensure that backup music data is available before performing this operation.
Malfunction disappears.
OK
NG
Turn the power switch off.
When this malfunction occurs, it is necessary to turn off the power switch to make it possible for the vehicle to recognize a new device when it is connected.
Turn the power switch on (ACC).
Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.
If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
Refer to System Description for compatible formats and versions (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>SYSTEM DESCRIPTION).
NEXT
Check if a USB device or "iPod" is recognized by the radio and display receiver assembly, and if information such as track, artist and album names are displayed on the screen.
Malfunction disappears.
OK
NG