Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM › 2016.05–2020.08
RM2070E _56 Audio / Visual / Telematics _061931 AUDIO / VIDEO _0301730 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Data Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit.

WIRING DIAGRAM

E345575E19
0.885,0.646 1.469,0.938 0.583,0.292 10 false US1- 0.865,2.198 1.448,2.49 0.583,0.292 10 false USG1 0.458,2.677 1.042,2.969 0.583,0.292 10 false L174 0.458,2.844 1.646,3.302 1.188,0.458 10 false No. 1 Stereo Jack Adapter Assembly 2.448,3.271 5.115,3.625 2.667,0.354 10 false : Data Signal (USB Communication Line) 5.531,2.635 6.115,2.927 0.583,0.292 10 false L175 5.531,2.802 6.76,3.24 1.229,0.438 10 false Radio and Display Receiver Assembly 5.927,2.219 6.51,2.51 0.583,0.292 10 false UJSS 3.25,1.76 4.01,2.094 0.76,0.333 10 false (Shielded) 1.333,0.531 1.917,0.823 0.583,0.292 10 false 2 1.344,1.302 1.927,1.594 0.583,0.292 10 false 3 1.354,2.104 1.938,2.396 0.583,0.292 10 false 5 0.875,1.448 1.458,1.74 0.583,0.292 10 false US1+ 5.938,0.646 6.521,0.938 0.583,0.292 10 false UDO- 5.917,1.448 6.5,1.74 0.583,0.292 10 false UDO+ 5.719,0.521 6.302,0.813 0.583,0.292 10 false 2 5.719,1.313 6.302,1.604 0.583,0.292 10 false 3 5.729,2.094 6.313,2.385 0.583,0.292 10 false 5

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the L175 radio and display receiver assembly connector.


b.

Disconnect the L174 No. 1 stereo jack adapter assembly connector.


c.
U191415E02
1.573,1.427 1.083,1.635 false 1.854,1.448 2.469,1.479 false 1.635,3.417 0.99,3.813 false 1.802,3.417 2.427,3.667 false 1.771,3.521 2.427,3.958 false 1.771,1.563 2.219,1.948 false 0.167,2.219 0.344,2.396 0.177,0.177 10 false *b 1.552,2.292 1.885,2.438 0.333,0.146 10 false L174 2.521,1.406 2.969,1.552 0.448,0.146 10 false UDO- 0.167,0.052 0.344,0.229 0.177,0.177 10 false *a 1.552,0.229 2.021,0.427 0.469,0.198 10 false L175 2.49,3.563 3.031,3.708 0.542,0.146 10 false US1+ 0.583,3.75 1.177,3.896 0.594,0.146 10 false US1- 0.625,1.594 1.083,1.74 0.458,0.146 10 false UDO+ 2.229,1.927 2.75,2.073 0.521,0.146 10 false UJSS 2.479,3.917 2.927,4.063 0.448,0.146 10 false USG1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L175-2 (UDO-) - L174-2 (US1-) Always Below 1 Ω
L175-3 (UDO+) - L174-3 (US1+) Always Below 1 Ω
L175-5 (UJSS) - L174-5 (USG1) Always Below 1 Ω
L175-2 (UDO-) - Body ground Always 10 kΩ or higher
L175-3 (UDO+) - Body ground Always 10 kΩ or higher
L175-5 (UJSS) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR