Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Radio Broadcast cannot be Received or Poor Reception  


PROCEDURE

1.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.

Check the radio automatic station search function.

i.

Check the radio automatic station search function by activating it.

Result:
Result Proceed to
Automatic station search function does not stop A
Automatic station search function stops on a station B





A

2.CHECK OPTIONAL COMPONENTS

B

2.CHECK OPTIONAL COMPONENTS
a.

Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

Result:
Result Proceed to
Optional components are not installed A
Optional components are installed B


NOTICE:

Do not remove optional components without the permission of the customer.




A

3.CHECK RADIO ANTENNA

B

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3.CHECK RADIO ANTENNA
a.

Preparation for check

i.

Remove the roof antenna pole sub-assembly from the amplifier antenna assembly.



b.

Check for noise

i.

Turn the power switch on (ACC) with the navigation ECU sub-assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire, or other metal object on the amplifier antenna threaded installation portion for the roof antenna pole sub-assembly and check that noise can be heard from the speakers.

Result:
Result Proceed to
Noise does not occur A
Noise occurs B





A

4.CHECK NAVIGATION ECU SUB-ASSEMBLY

B

4.CHECK NAVIGATION ECU SUB-ASSEMBLY
a.
E187251

Preparation for check

i.

Remove the antenna connector from the navigation ECU sub-assembly.



b.

Check for noise

i.

Turn the power switch on (ACC) with the navigation ECU sub-assembly connector connected.


ii.

Turn the radio on and tune into AM mode.


iii.

Place a screwdriver, thin wire or other metal object on the navigation ECU sub-assembly antenna jack and check that noise can be heard from the speakers.

OK:

Noise can be heard from the speakers.





OK

5.INSPECT NAVIGATION ECU SUB-ASSEMBLY

NG

5.INSPECT NAVIGATION ECU SUB-ASSEMBLY
a.

Disconnect the RA navigation ECU sub-assembly connector.


b.
U111431E01
0.095,0.056 0.274,0.221 0.179,0.165 10 *a 0.624,1.017 0.847,1.180 0.223,0.162 10 RA 0.838,1.477 1.232,1.645 0.393,0.167 10 ANT+ 1.538,1.096 1.136,1.443 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
RA-5 (ANT+) - Body ground Power switch on (ACC)
Radio switch on and AM or FM selected
11 to 14 V


Text in Illustration
*a Component without harness connected
(Navigation ECU Sub-assembly)



OK

6.REPLACE ANTENNA CORD SUB-ASSEMBLY

NG

6.REPLACE ANTENNA CORD SUB-ASSEMBLY
a.

Replace the antenna cord sub-assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG

7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
7.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the No. 2 antenna cord sub-assembly.


b.

Measure the resistance of the No. 2 antenna cord sub-assembly to check for an open circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

Below 1 Ω



c.

Measure the resistance between the No. 2 antenna cord sub-assembly and body ground to check for a short circuit in the No. 2 antenna cord sub-assembly.

Standard Resistance:

10 kΩ or higher




OK

8.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

8.CHECK ROOF ANTENNA POLE SUB-ASSEMBLY
a.

Check that the roof antenna pole sub-assembly is securely installed (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA(for Roof)>REMOVAL).

OK:

The roof antenna pole sub-assembly is installed properly.




OK

9.REPLACE AMPLIFIER ANTENNA ASSEMBLY

NG

CHECK AND REPLACE ROOF ANTENNA POLE SUB-ASSEMBLY

9.REPLACE AMPLIFIER ANTENNA ASSEMBLY
a.

Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (See page Audio / Visual / Telematics>AUDIO / VIDEO>AMPLIFIER ANTENNA(for Roof)>REMOVAL).

OK:

Radio broadcasts can be received normally.




OK

NORMAL OPERATION

NG