Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Sound Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound signal from an external device to the navigation ECU sub-assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E229861E71
0.813,0.792 1.24,0.948 0.427,0.156 10 false AUXO 0.896,1.271 1.323,1.427 0.427,0.156 10 false ARO 0.938,1.75 1.365,1.906 0.427,0.156 10 false ALO 0.813,2.219 1.24,2.375 0.427,0.156 10 false ASGN 0.813,2.708 1.24,2.865 0.427,0.156 10 false AGND 2.5,2.833 3.156,2.99 0.656,0.156 10 false (Shielded) 4.031,2.833 4.688,2.99 0.656,0.156 10 false (Shielded) 5.927,0.792 6.354,0.948 0.427,0.156 10 false ADPG 5.927,1.271 6.354,1.427 0.427,0.156 10 false VAR+ 5.698,0.688 5.875,0.844 0.177,0.156 10 false 25 5.698,1.167 5.875,1.323 0.177,0.156 10 false 26 5.698,1.635 5.875,1.792 0.177,0.156 10 false 28 5.698,2.104 5.875,2.26 0.177,0.156 10 false 27 5.698,2.594 5.875,2.75 0.177,0.156 10 false 11 1.323,0.698 1.5,0.854 0.177,0.156 10 false 9 1.323,1.167 1.5,1.323 0.177,0.156 10 false 6 1.323,1.646 1.5,1.802 0.177,0.156 10 false 7 1.323,2.104 1.5,2.26 0.177,0.156 10 false 8 1.333,2.594 1.51,2.75 0.177,0.156 10 false 10 0.427,3.115 0.781,3.271 0.354,0.156 10 false L13 0.427,3.281 1.667,3.677 1.24,0.396 10 false No. 1 Stereo Jack Adapter Assembly 5.771,3.271 6.792,3.583 1.021,0.313 10 false Navigation ECU Sub-assembly 5.927,1.75 6.354,1.906 0.427,0.156 10 false VAL+ 5.927,2.229 6.354,2.385 0.427,0.156 10 false VA- 5.927,2.708 6.354,2.865 0.427,0.156 10 false AGND 5.771,3.115 6.208,3.271 0.438,0.156 10 false L38

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
U191336E01
2.117,1.416 2.779,1.172 false 2.828,1.087 3.250,1.233 0.422,0.145 10 AGND 2.218,1.631 2.074,1.963 false 1.814,1.981 2.231,2.126 0.417,0.145 10 VAR+ 2.112,1.631 1.593,1.963 false 1.178,1.981 1.595,2.126 0.417,0.145 10 ADPG 2.45,1.631 2.969,1.963 false 2.889,1.981 3.253,2.126 0.364,0.145 10 VAL+ 2.335,1.631 2.479,1.963 false 2.415,1.981 2.664,2.126 0.248,0.145 10 VA- 0.18,0.169 0.343,0.335 0.163,0.166 10 *a 1.587,0.278 1.929,0.433 0.342,0.156 10 L38 1.583,3.873 1.18,4.232 false 2.529,3.761 2.951,3.907 0.422,0.145 10 AGND 0.924,4.256 1.242,4.401 0.317,0.145 10 ALO 1.87,3.873 2.273,4.232 false 2.157,4.256 2.571,4.401 0.415,0.145 10 AUXO 0.181,2.231 0.382,2.398 0.201,0.166 10 *b 2.049,3.835 2.498,3.835 false 1.403,3.834 0.884,3.834 false 1.73,3.875 1.729,4.417 false 0.46,3.744 0.816,3.890 0.356,0.145 10 ARO 1.485,4.431 1.907,4.577 0.422,0.145 10 ASGN 1.587,2.325 1.929,2.481 0.343,0.156 10 L13

Disconnect the L38 navigation ECU sub-assembly connector.


b.

Disconnect the L13 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-25 (ADPG) - L13-9 (AUXO) Always Below 1 Ω
L38-26 (VAR+) - L13-6 (ARO) Always Below 1 Ω
L38-28 (VAL+) - L13-7 (ALO) Always Below 1 Ω
L38-27 (VA-) - L13-8 (ASGN) Always Below 1 Ω
L38-11 (AGND) - L13-10 (AGND) Always Below 1 Ω
L38-25 (ADPG) - Body ground Always 10 kΩ or higher
L38-26 (VAR+) - Body ground Always 10 kΩ or higher
L38-28 (VAL+) - Body ground Always 10 kΩ or higher
L38-27 (VA-) - Body ground Always 10 kΩ or higher
L38-11 (AGND) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR