Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Mute Signal Circuit between Navigation Receiver Assembly and Stereo Component Amplifier  


DESCRIPTION

This circuit sends a signal to the stereo component amplifier assembly to mute noise. Due to this, the noise produced by changing the sound source ceases.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E261261E59
1.219,1.104 1.833,1.302 0.615,0.198 10 false MUTE 5.51,1.115 6.125,1.313 0.615,0.198 10 false MUT2 1.719,0.99 2.333,1.188 0.615,0.198 10 false 1 5.281,1 5.604,1.198 0.323,0.198 10 false 20 0.656,2 1.271,2.198 0.615,0.198 10 false L31 0.646,2.156 1.865,2.604 1.219,0.448 10 false Stereo Component Amplifier Assembly 5.427,2 6.042,2.198 0.615,0.198 10 false L38 5.427,2.156 6.406,2.615 0.979,0.458 10 false Navigation ECU Sub-assembly

PROCEDURE

1.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY
a.
U191323E02
2.396,1.885 2.865,2.385 false 0.208,0.167 0.365,0.333 0.156,0.167 10 false *a 1.594,0.875 1.927,1.042 0.333,0.167 10 false L31 2.698,2.417 3.125,2.583 0.427,0.167 10 false MUTE

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L31-1 (MUTE) - Body ground Power switch on (ACC), audio system playing
→ Changing modes
Above 3.5 V
→ Below 1 V


Text in Illustration
*a Component with harness connected
(Stereo Component Amplifier Assembly)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L38 navigation ECU sub-assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-20 (MUT2) - L31-1 (MUTE) Always Below 1 Ω
L38-20 (MUT2) - Body ground Always 10 kΩ or higher




OK

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (OUTPUT SIGNAL)
a.

Reconnect the L31 stereo component amplifier assembly.


b.
U191286E01
1.588,0.672 1.927,0.828 0.339,0.156 10 L38 0.181,0.157 0.336,0.312 0.154,0.156 10 *a 1.054,2.735 1.450,2.890 0.396,0.156 10 MUT2 1.55,2.222 1.371,2.72 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L38-20 (MUT2) - Body ground Power switch on (ACC), audio system is playing Above 3.5 V


Text in Illustration
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY