Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301737 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B15D8  Monitor Disconnected  


DESCRIPTION

The navigation ECU sub-assembly and parking assist ECU are connected via AVC-LAN communication.

When an AVC-LAN communication error occurs between the navigation ECU sub-assembly and parking assist ECU, this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B15D8 Parking assist ECU is not/was not connected while the power switch is/was on (ACC or IG).
·

Parking assist ECU power source circuit

·

AVC-LAN circuit between navigation ECU sub-assembly and parking assist ECU

·

Parking assist ECU

·

Navigation ECU sub-assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the auxiliary battery condition or hybrid system start voltage.

·

The navigation ECU sub-assembly is the master unit.



WIRING DIAGRAM

E230081E06
5.529,4.033 5.920,4.201 0.392,0.169 10 L64 5.529,4.215 6.808,4.367 1.279,0.152 10 Parking Assist ECU 3.3,3.586 3.637,3.755 0.336,0.169 10 L37 3.3,3.754 4.357,4.101 1.056,0.347 10 Navigation ECU Sub-assembly 0.404,0.511 1.783,0.688 1.379,0.177 10 from Auxiliary Battery 3.459,0.749 4.184,0.926 0.725,0.177 10 RAD NO. 1 3.508,1.548 4.165,1.725 0.657,0.177 10 ECU-ACC 3.372,2.338 4.285,2.515 0.914,0.177 10 ECU-IG NO. 2 5.686,1.317 5.999,1.493 0.313,0.177 10 ACC 5.686,0.532 5.906,0.709 0.221,0.177 10 +B 5.5,0.427 5.631,0.604 0.130,0.177 10 1 5.535,1.215 5.641,1.392 0.106,0.177 10 9 5.686,2.112 5.881,2.289 0.195,0.177 10 IG 5.521,2.01 5.627,2.187 0.106,0.177 10 8 5.686,2.907 6.086,3.084 0.400,0.177 10 TX+ 3.976,2.907 4.345,3.084 0.369,0.177 10 TX3+ 5.449,2.805 5.625,2.982 0.177,0.177 10 11 5.686,3.692 6.117,3.869 0.431,0.177 10 GND1 5.507,3.591 5.616,3.768 0.109,0.177 10 4 4.415,2.805 4.524,2.982 0.109,0.177 10 3 5.686,3.31 6.113,3.486 0.428,0.177 10 TX- 4.001,3.31 4.401,3.486 0.400,0.177 10 TX3- 5.449,3.208 5.639,3.385 0.190,0.177 10 10 4.415,3.208 4.524,3.385 0.109,0.177 10 4 0.689,1.313 1.716,1.490 1.027,0.177 10 from ACC Relay 0.356,2.102 1.713,2.279 1.357,0.177 10 from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.




NEXT

3.CHECK DTC
3.CHECK DTC

b.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - AUXILIARY BATTERY, BODY GROUND)
4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - AUXILIARY BATTERY, BODY GROUND)
a.

Disconnect the L64 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L64-4 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L64-1 (+B) - L64-4 (GND1) Power switch off 11 to 14 V
L64-8 (IG) - L64-4 (GND1) Power switch on (IG) 11 to 14 V
L64-9 (ACC) - L64-4 (GND1) Power switch on (ACC) 11 to 14 V




OK

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NAVIGATION ECU SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - NAVIGATION ECU SUB-ASSEMBLY)
a.

Disconnect the L64 parking assist ECU connector.


b.

Disconnect the L37 navigation ECU sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L64-11 (TX+) - L37-3 (TX3+) Always Below 1 Ω
L64-10 (TX-) - L37-4 (TX3-) Always Below 1 Ω
L64-11 (TX+) - Body ground Always 10 kΩ or higher
L64-10 (TX-) - Body ground Always 10 kΩ or higher




OK

6.REPLACE PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE PARKING ASSIST ECU


c.

Recheck for DTCs and check if the same DTC is output again.

OK:

No DTCs are output.




OK

END

NG