Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Radio Receiver Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the radio and display receiver assembly.

WIRING DIAGRAM

E287097E77
0.469,0.771 1.917,1.01 1.448,0.24 10 false from Auxiliary Battery 0.781,1.573 2.615,1.771 1.833,0.198 10 false from ACC Relay 0.49,2.375 2.323,2.573 1.833,0.198 10 false from IG1 NO. 1 Relay 3.375,0.948 4.313,1.188 0.938,0.24 10 false RAD NO. 1 3.406,1.75 4.302,1.99 0.896,0.24 10 false ECU-ACC 3.302,2.542 4.313,2.823 1.01,0.281 10 false ECU-IG NO. 2 5.531,3.625 6.729,4.115 1.198,0.49 10 false Radio and Display Receiver Assembly 5.406,0.802 5.802,1 0.396,0.198 10 false L167 5.406,1.583 5.792,1.781 0.385,0.198 10 false L167 5.438,2.375 5.781,2.573 0.344,0.198 10 false L35 5.406,3.167 5.802,3.365 0.396,0.198 10 false L167 5.521,2.99 5.833,3.188 0.313,0.198 10 false 7 5.51,2.188 5.823,2.385 0.313,0.198 10 false 1 5.51,1.385 5.823,1.583 0.313,0.198 10 false 3 5.51,0.604 5.823,0.802 0.313,0.198 10 false 4 5.802,0.792 6.26,1.021 0.458,0.229 10 false +B1 5.802,1.573 6.26,1.802 0.458,0.229 10 false ACC1 5.813,2.375 6.271,2.604 0.458,0.229 10 false IG 5.813,3.167 6.271,3.396 0.458,0.229 10 false GND1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the L167 and L35 radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L167-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L167-4 (+B1) - L167-7 (GND1) Power switch off 11 to 14 V
L167-3 (ACC1) - L167-7 (GND1) Power switch on (ACC) 11 to 14 V
L35-1 (IG) - L167-7 (GND1) Power switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR