Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2016.05–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter sub-assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter sub-assembly. The signal is changed to a pulse signal at the transistor in the combination meter sub-assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E348155E03
0.677,1.375 1.094,1.563 0.417,0.188 10 false A58 0.667,1.531 2.083,1.719 1.417,0.188 10 false Skid Control ECU 1.792,0.458 2.208,0.646 0.417,0.188 10 false 11 1.458,0.458 1.875,0.646 0.417,0.188 10 false SP1 1.427,2.396 1.844,2.583 0.417,0.188 10 false SPD 1.438,3.875 1.854,4.063 0.417,0.188 10 false SPD 1.406,5.229 1.823,5.417 0.417,0.188 10 false SPD 1.323,6.563 1.74,6.75 0.417,0.188 10 false SPDR 5.563,2.385 5.979,2.573 0.417,0.188 10 false SPD 5.563,3.875 5.979,4.063 0.417,0.188 10 false SPD 5.563,5.219 5.979,5.406 0.417,0.188 10 false SPD 5.552,6.563 5.969,6.75 0.417,0.188 10 false SPD 5.552,0.5 5.969,0.688 0.417,0.188 10 false S1 5.292,0.49 5.51,0.677 0.219,0.188 10 false 16 5.552,0.896 5.969,1.083 0.417,0.188 10 false +S 5.292,0.896 5.51,1.083 0.219,0.188 10 false 15 4.958,1.365 5.375,1.552 0.417,0.188 10 false L27 4.948,1.51 7.115,1.698 2.167,0.188 10 false Combination Meter Sub-assembly 3.531,1.802 3.917,1.99 0.385,0.188 10 false 31*2 3.542,1.667 3.927,1.854 0.385,0.188 10 false 32*1 3.917,2.396 4.302,2.583 0.385,0.188 10 false 11*9 3.917,3.875 4.302,4.063 0.385,0.188 10 false 12*2 3.917,3.74 4.302,3.927 0.385,0.188 10 false 3*1 3.917,6.563 4.302,6.75 0.385,0.188 10 false 11*2 3.917,6.427 4.302,6.615 0.385,0.188 10 false 21*1 2.76,6.552 3.146,6.74 0.385,0.188 10 false 32*2 2.76,6.417 3.146,6.604 0.385,0.188 10 false 31*1 2.833,5.229 3.219,5.417 0.385,0.188 10 false 3*2 2.833,5.094 3.219,5.281 0.385,0.188 10 false 1*1 2.76,3.865 3.146,4.052 0.385,0.188 10 false 21*2 2.771,3.74 3.156,3.927 0.385,0.188 10 false 12*1 2.885,2.396 3.271,2.583 0.385,0.188 10 false 22 1.781,2.396 2.167,2.583 0.385,0.188 10 false 27 0.094,2.771 0.51,2.958 0.417,0.188 10 false L197 0.083,2.927 3.042,3.115 2.958,0.188 10 false Certification ECU (Smart Key ECU Assembly) 4.448,2.771 4.865,2.958 0.417,0.188 10 false L188 4.448,2.927 7.146,3.115 2.698,0.188 10 false Vehicle Approaching Speaker Controller*9 5.375,2.396 5.76,2.583 0.385,0.188 10 false 6 4.531,4.188 4.948,4.375 0.417,0.188 10 false L35 4.531,4.344 7.146,4.531 2.615,0.188 10 false Radio and Display Receiver Assembly*5 4.813,5.563 5.229,5.75 0.417,0.188 10 false L38 4.813,5.719 7.146,5.906 2.333,0.188 10 false Navigation Receiver Assembly*6 5.323,3.875 5.708,4.063 0.385,0.188 10 false 17 5.323,5.219 5.708,5.406 0.385,0.188 10 false 17 5.313,6.552 5.698,6.74 0.385,0.188 10 false 11 4.625,6.875 5.042,7.063 0.417,0.188 10 false L31 4.625,7.021 7.135,7.24 2.51,0.219 10 false Stereo Component Amplifier Assembly*7 2.74,7.073 3.156,7.26 0.417,0.188 10 false L70 3.042,7.073 5.167,7.26 2.125,0.188 10 false Junction Connector 0.135,6.896 0.552,7.083 0.417,0.188 10 false A48 0.135,7.052 2.885,7.24 2.75,0.188 10 false Headlight Leveling ECU Assembly*4 1.792,6.552 2.177,6.74 0.385,0.188 10 false 16 0.063,5.667 2.865,5.854 2.802,0.188 10 false Tire Pressure Warning ECU and Receiver*8 1.792,5.219 2.177,5.406 0.385,0.188 10 false 2 0.063,5.5 0.479,5.688 0.417,0.188 10 false R41 0.125,4.313 2.927,4.5 2.802,0.188 10 false Windshield Wiper Relay Assembly*3 0.135,4.146 0.552,4.333 0.417,0.188 10 false L146 1.802,3.875 2.188,4.063 0.385,0.188 10 false 24 0.188,7.521 1.063,7.708 0.875,0.188 10 false *1: for LHD 1.698,7.51 2.573,7.698 0.875,0.188 10 false *2: for RHD 3.052,7.51 4.896,7.698 1.844,0.188 10 false *3: w/ Auto Wiper System 5.396,7.51 7.115,8.021 1.719,0.51 10 false *4: w/ LED Headlight 0.188,7.938 2.656,8.125 2.469,0.188 10 false *5: for Radio and Display Type 3.063,7.938 5.531,8.125 2.469,0.188 10 false *6: for Navigation Receiver Type 5.396,7.938 7.115,8.448 1.719,0.51 10 false *7:for 8 Speakers 0.188,8.313 2.656,8.5 2.469,0.188 10 false *8: w/ Tire Pressure Warning System 3.052,8.323 5.917,8.51 2.865,0.188 10 false *9: w/ Vehicle Proximity Notification System

PROCEDURE

1.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)
a.
U191399E02
0.99,2.042 1.281,1.354 false 0.094,0.052 0.25,0.208 0.156,0.156 10 false *a 0.885,2.083 1.073,2.24 0.188,0.156 10 false +S 2.813,3.583 3.135,3.74 0.323,0.156 10 false GND 1.135,3.833 1.344,3.99 0.208,0.156 10 false A 1.615,0.417 1.917,0.573 0.302,0.156 10 false L27

Check the output waveform.

i.

Remove the combination meter sub-assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L27-15 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Sub-assembly)




OK

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - COMBINATION METER SUB-ASSEMBLY)
a.

Disconnect the L31 stereo component amplifier assembly connector.


b.

Disconnect the L27 combination meter sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-11 (SPD) - L27-15 (+S) Always Below 1 Ω




OK

NG

3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
3.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L31 stereo component amplifier assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-11 (SPD) - L70-21*1 Always Below 1 Ω
L31-11 (SPD) - L70-11*2 Always Below 1 Ω


*1: for LHD

*2: for RHD




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-32*1 Always Below 1 Ω
L27-15 (+S) - L70-31*2 Always Below 1 Ω


*1: for LHD

*2: for RHD




OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR