Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2020.08
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier  


DESCRIPTION

The radio and display receiver assembly sends a sound signal to the stereo component amplifier assembly via this circuit.

The sound signal that has been sent is amplified by the stereo component amplifier assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly or speakers.

WIRING DIAGRAM

E268437E40
0.365,3.677 1.563,4.229 1.198,0.552 10 false Radio and Display Receiver Assembly 0.354,3.479 0.854,3.719 0.5,0.24 10 false L167 5.688,3.469 6,3.667 0.313,0.198 10 false L31 5.677,3.646 6.875,4.188 1.198,0.542 10 false Stereo Component Amplifier Assembly 3.26,2.74 3.969,3.01 0.708,0.271 10 false (Shielded) 0.927,0.635 1.292,0.854 0.365,0.219 10 false FR+ 0.969,1.208 1.333,1.427 0.365,0.219 10 false FR- 0.948,1.833 1.313,2.052 0.365,0.219 10 false FL+ 0.969,2.427 1.333,2.646 0.365,0.219 10 false FL- 1.344,1.104 1.5,1.333 0.156,0.229 10 false 5 1.344,0.521 1.5,0.75 0.156,0.229 10 false 1 1.354,1.708 1.51,1.938 0.156,0.229 10 false 2 1.354,2.292 1.51,2.521 0.156,0.229 10 false 6 5.76,0.521 5.917,0.75 0.156,0.229 10 false 5 5.76,1.125 5.917,1.354 0.156,0.229 10 false 4 5.76,1.708 5.917,1.938 0.156,0.229 10 false 3 5.76,2.292 5.917,2.521 0.156,0.229 10 false 2 5.75,2.875 5.906,3.104 0.156,0.229 10 false 6 6,0.625 6.313,0.823 0.313,0.198 10 false R+ 6,1.24 6.313,1.438 0.313,0.198 10 false R- 6,1.813 6.313,2.01 0.313,0.198 10 false L+ 6,2.417 6.313,2.615 0.313,0.198 10 false L- 5.99,3.021 6.344,3.219 0.354,0.198 10 false SLD

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the L167 radio and display receiver assembly connector.


b.

Disconnect the L31 stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-5 (R+) - L167-1 (FR+) Always Below 1 Ω
L31-4 (R-) - L167-5 (FR-) Always Below 1 Ω
L31-3 (L+) - L167-2 (FL+) Always Below 1 Ω
L31-2 (L-) - L167-6 (FL-) Always Below 1 Ω
L31-6 (SLD) - Body ground Always 10 kΩ or higher
L31-5 (R+) - Body ground Always 10 kΩ or higher
L31-4 (R-) - Body ground Always 10 kΩ or higher
L31-3 (L+) - Body ground Always 10 kΩ or higher
L31-2 (L-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR