Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for Radio and Display Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301739 NAVIGATION SYSTEM(for Radio and Display Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  Data Signal Circuit between Stereo Jack Adapter and Extension Module  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the navigation ECU via this circuit.

WIRING DIAGRAM

E345575E20
0.885,0.646 1.469,0.938 0.583,0.292 10 false UDO- 0.865,2.198 1.448,2.49 0.583,0.292 10 false USG1 0.458,2.677 1.042,2.969 0.583,0.292 10 false L174 0.458,2.844 1.646,3.302 1.188,0.458 10 false No. 1 Stereo Jack Adapter Assembly 2.448,3.271 5.115,3.625 2.667,0.354 10 false : Data Signal (USB Communication Line) 5.74,2.646 6.323,2.938 0.583,0.292 10 false L175 5.729,2.802 6.958,3.24 1.229,0.438 10 false Navigation ECU 5.927,2.219 6.51,2.51 0.583,0.292 10 false USG1 3.26,1.76 4.021,2.094 0.76,0.333 10 false (Shielded) 1.333,0.531 1.917,0.823 0.583,0.292 10 false 2 1.344,1.302 1.927,1.594 0.583,0.292 10 false 3 1.354,2.104 1.938,2.396 0.583,0.292 10 false 5 0.854,1.448 1.438,1.74 0.583,0.292 10 false UDO+ 5.938,0.646 6.521,0.938 0.583,0.292 10 false US1- 5.917,1.448 6.5,1.74 0.583,0.292 10 false US1+ 5.719,0.521 6.302,0.813 0.583,0.292 10 false 2 5.719,1.313 6.302,1.604 0.583,0.292 10 false 3 5.729,2.094 6.313,2.385 0.583,0.292 10 false 5

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.
U191411E02
1.573,1.427 1.083,1.635 false 1.844,1.427 2.458,1.458 false 1.635,3.417 0.99,3.813 false 1.802,3.417 2.427,3.667 false 1.771,3.521 2.427,3.958 false 1.771,1.563 2.219,1.948 false 0.167,2.219 0.344,2.396 0.177,0.177 10 false *b 1.604,2.302 1.938,2.448 0.333,0.146 10 false L174 0.51,3.75 0.958,3.896 0.448,0.146 10 false UDO- 0.167,0.052 0.344,0.229 0.177,0.177 10 false *a 1.594,0.219 1.927,0.365 0.333,0.146 10 false L175 0.552,1.573 1.094,1.719 0.542,0.146 10 false US1+ 2.469,1.396 3.063,1.542 0.594,0.146 10 false US1- 2.448,3.583 2.906,3.729 0.458,0.146 10 false UDO+ 2.448,3.896 2.969,4.042 0.521,0.146 10 false USG1 2.26,1.885 2.708,2.031 0.448,0.146 10 false USG1

Disconnect the L175 navigation ECU connector.


b.

Disconnect the L174 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L175-2 (US1-) - L174-2 (UDO-) Always Below 1 Ω
L175-3 (US1+) - L174-3 (UDO+) Always Below 1 Ω
L175-5 (USG1) - L174-5 (USG1) Always Below 1 Ω
L175-2 (US1-) - Body ground Always 10 kΩ or higher
L175-3 (US1+) - Body ground Always 10 kΩ or higher
L175-5 (USG1) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Navigation ECU)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR