Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Navigation Receiver Assembly Power Source Circuit  


DESCRIPTION

This is the power source circuit to operate the navigation receiver assembly.

WIRING DIAGRAM

E287097E75
0.448,0.771 1.865,0.948 1.417,0.177 10 false from Auxiliary Battery 0.802,1.573 2.229,1.75 1.427,0.177 10 false from ACC Relay 0.448,2.375 1.917,2.552 1.469,0.177 10 false from IG1 NO. 1 Relay 5.844,0.771 6.146,0.979 0.302,0.208 10 false +B1 5.844,1.594 6.229,1.771 0.385,0.177 10 false ACC1 5.844,2.385 6.01,2.563 0.167,0.177 10 false IG 5.844,3.167 6.25,3.344 0.406,0.177 10 false GND1 5.417,0.792 5.802,0.969 0.385,0.177 10 false L171 5.417,1.583 5.771,1.76 0.354,0.177 10 false L171 5.448,2.375 5.781,2.552 0.333,0.177 10 false L38 5.417,3.156 5.75,3.333 0.333,0.177 10 false L171 5.521,0.563 5.677,0.74 0.156,0.177 10 false 4 5.521,1.375 5.677,1.552 0.156,0.177 10 false 3 5.521,2.135 5.677,2.313 0.156,0.177 10 false 1 5.521,2.958 5.677,3.135 0.156,0.177 10 false 7 3.323,0.948 4.104,1.125 0.781,0.177 10 false RAD NO. 1 3.333,1.729 4.104,1.906 0.771,0.177 10 false ECU-ACC 3.25,2.521 4.25,2.698 1,0.177 10 false ECU-IG NO. 2 5.49,3.604 6.76,4.083 1.271,0.479 10 false Navigation Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the L171 and L38 navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L171-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L171-4 (+B1) - L171-7 (GND1) Power switch off 11 to 14 V
L171-3 (ACC1) - L171-7 (GND1) Power switch on (ACC) 11 to 14 V
L38-1 (IG) - L171-7 (GND1) Power switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR