Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15C2  Speed Signal Malfunction  


DESCRIPTION

The navigation receiver assembly receives a vehicle speed signal from the combination meter sub-assembly and information from the navigation antenna assembly, and then adjusts the vehicle position.

The navigation receiver assembly stores this DTC when the difference between the speed information that the navigation antenna assembly and the SPD pulse received from the combination meter sub-assembly becomes large.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter sub-assembly. The signal is changed to a pulse signal at the transistor in the combination meter sub-assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



DTC No. DTC Detection Condition Trouble Area
B15C2 A difference between the GPS speed and SPD pulse is detected
·

Navigation receiver assembly

·

Combination meter sub-assembly

·

Harness or connector

·

Junction connector



WIRING DIAGRAM

E348155E02
0.677,1.365 1.094,1.552 0.417,0.188 10 false A58 0.667,1.531 2.083,1.719 1.417,0.188 10 false Skid Control ECU 1.792,0.458 2.208,0.646 0.417,0.188 10 false 11 1.458,0.458 1.875,0.646 0.417,0.188 10 false SP1 1.427,2.396 1.844,2.583 0.417,0.188 10 false SPD 1.438,3.875 1.854,4.063 0.417,0.188 10 false SPD 1.406,5.229 1.823,5.417 0.417,0.188 10 false SPD 1.323,6.563 1.74,6.75 0.417,0.188 10 false SPDR 5.563,2.396 5.979,2.583 0.417,0.188 10 false SPD 5.563,3.875 5.979,4.063 0.417,0.188 10 false SPD 5.563,5.219 5.979,5.406 0.417,0.188 10 false SPD 5.552,6.563 5.969,6.75 0.417,0.188 10 false SPD 5.552,0.5 5.969,0.688 0.417,0.188 10 false S1 5.292,0.49 5.51,0.677 0.219,0.188 10 false 16 5.552,0.896 5.969,1.083 0.417,0.188 10 false +S 5.292,0.896 5.51,1.083 0.219,0.188 10 false 15 4.958,1.365 5.375,1.552 0.417,0.188 10 false L27 4.948,1.51 7.115,1.698 2.167,0.188 10 false Combination Meter Sub-assembly 3.531,1.802 3.917,1.99 0.385,0.188 10 false 31*2 3.542,1.667 3.927,1.854 0.385,0.188 10 false 32*1 3.917,2.396 4.302,2.583 0.385,0.188 10 false 11*9 3.917,3.875 4.302,4.063 0.385,0.188 10 false 12*2 3.917,3.74 4.302,3.927 0.385,0.188 10 false 3*1 3.917,6.563 4.302,6.75 0.385,0.188 10 false 11*2 3.917,6.427 4.302,6.615 0.385,0.188 10 false 21*1 2.76,6.552 3.146,6.74 0.385,0.188 10 false 32*2 2.76,6.417 3.146,6.604 0.385,0.188 10 false 31*1 2.833,5.229 3.219,5.417 0.385,0.188 10 false 3*2 2.833,5.094 3.219,5.281 0.385,0.188 10 false 1*1 2.76,3.865 3.146,4.052 0.385,0.188 10 false 21*2 2.771,3.729 3.156,3.917 0.385,0.188 10 false 12*1 2.885,2.396 3.271,2.583 0.385,0.188 10 false 22 1.781,2.396 2.167,2.583 0.385,0.188 10 false 27 0.094,2.771 0.51,2.958 0.417,0.188 10 false L197 0.083,2.927 3.042,3.115 2.958,0.188 10 false Certification ECU (Smart Key ECU Assembly) 4.521,2.771 4.938,2.958 0.417,0.188 10 false L188 4.521,2.927 7.125,3.125 2.604,0.198 10 false Vehicle Approaching Speaker Controller*9 5.375,2.396 5.76,2.583 0.385,0.188 10 false 6 4.656,4.188 5.073,4.375 0.417,0.188 10 false L35 4.656,4.344 7.156,4.552 2.5,0.208 10 false Radio and Display Receiver Assembly*5 5.063,5.563 5.479,5.75 0.417,0.188 10 false L38 5.063,5.719 7.156,5.958 2.094,0.24 10 false Navigation Receiver Assembly*6 5.323,3.875 5.708,4.063 0.385,0.188 10 false 17 5.323,5.219 5.708,5.406 0.385,0.188 10 false 17 5.313,6.552 5.698,6.74 0.385,0.188 10 false 11 4.604,6.875 5.021,7.063 0.417,0.188 10 false L31 4.594,7.031 7.156,7.26 2.563,0.229 10 false Stereo Component Amplifier Assembly*7 2.74,7.073 3.156,7.26 0.417,0.188 10 false L70 3.042,7.073 5.167,7.26 2.125,0.188 10 false Junction Connector 0.135,6.896 0.552,7.083 0.417,0.188 10 false A48 0.135,7.052 2.885,7.24 2.75,0.188 10 false Headlight Leveling ECU Assembly*4 1.792,6.552 2.177,6.74 0.385,0.188 10 false 16 0.063,5.667 2.865,5.854 2.802,0.188 10 false Tire Pressure Warning ECU and Receiver*8 1.792,5.219 2.177,5.406 0.385,0.188 10 false 2 0.063,5.5 0.479,5.688 0.417,0.188 10 false R41 0.125,4.313 2.927,4.5 2.802,0.188 10 false Windshield Wiper Relay Assembly*3 0.135,4.156 0.552,4.344 0.417,0.188 10 false L146 1.802,3.875 2.188,4.063 0.385,0.188 10 false 24 0.188,7.521 1.063,7.708 0.875,0.188 10 false *1: for LHD 1.698,7.51 2.573,7.698 0.875,0.188 10 false *2: for RHD 3.052,7.51 4.896,7.698 1.844,0.188 10 false *3: w/ Auto Wiper System 5.396,7.51 7.115,8.021 1.719,0.51 10 false *4: w/ LED Headlight 0.188,7.938 2.656,8.125 2.469,0.188 10 false *5: for Radio and Display Type 3.063,7.938 5.531,8.125 2.469,0.188 10 false *6: for Navigation Receiver Type 5.396,7.938 7.115,8.448 1.719,0.51 10 false *7:for 8 Speakers 0.188,8.313 2.656,8.5 2.469,0.188 10 false *8: w/ Tire Pressure Warning System 3.052,8.323 5.917,8.51 2.865,0.188 10 false *9: w/ Vehicle Proximity Notification System

PROCEDURE

1.CHECK SYSTEM SENSORS (OPERATION CHECK)
a.
E276610

Enter the "System Sensors Check" screen.

Refer to Check System Sensors in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>OPERATION CHECK).


b.

While driving the vehicle, compare the value of "Speed" to the reading on the speedometer. Check if these readings are almost equal.

HINT:

The combination meter sub-assembly receives the vehicle speed signal from the skid control ECU via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU because it is the source of the vehicle speed signal.


OK:

Vehicle speed displayed on the "System Sensors Check" screen is almost the same as the actual vehicle speed measured using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST).




OK

NG

2.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER SUB-ASSEMBLY (OUTPUT WAVEFORM)
a.
U155149E01
0.098,0.053 0.255,0.209 0.158,0.155 10 *a 0.883,2.059 1.076,2.215 0.192,0.155 10 +S 2.815,3.566 3.143,3.722 0.328,0.155 10 GND 1.135,3.837 1.347,3.992 0.211,0.155 10 A 0.991,2.016 1.28,1.332 false 1.614,0.387 1.917,0.543 0.303,0.156 10 L27

Check the output waveform.

i.

Remove the combination meter sub-assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L27-15 (+S) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L27-15 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.


Text in Illustration
*a Component with harness connected
(Combination Meter Sub-assembly)




OK

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)

NG

3.INSPECT NAVIGATION RECEIVER ASSEMBLY (INPUT WAVEFORM)
a.
U155162E01
0.125,0.16 0.282,0.316 0.158,0.155 10 *a 2.468,2.206 2.862,2.362 0.394,0.155 10 SPD 2.971,3.717 3.299,3.872 0.328,0.155 10 GND 1.294,4.009 1.505,4.164 0.211,0.155 10 A 2.612,2.154 2.412,1.487 false 1.655,0.237 1.913,0.393 0.258,0.156 10 L38

Check the input waveform.

i.

Remove the navigation receiver assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal L38-17 (SPD) and body ground.


iii.

Turn the power switch on (IG).


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal L38-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Text in Illustration
*a Component with harness connected
(Navigation Receiver Assembly)


OK

NG

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L38 navigation receiver assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L38-17 (SPD) - L70-3 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L38-17 (SPD) - L70-12 Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - JUNCTION CONNECTOR)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the L70 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-32 Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L27-15 (+S) - L70-31 Always Below 1 Ω




OK

REPLACE JUNCTION CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR