This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B15C3 | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Stereo component amplifier assembly |
Disconnect the L30 stereo component amplifier assembly connector.
Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
Disconnect the I6 and I7 front No. 2 speaker assembly connectors.
Disconnect the P3 and Q3 rear speaker assembly connectors.
Disconnect the P5 and Q5 rear No. 2 speaker assembly connectors.
Measure the resistance between the stereo component amplifier assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L30-15 (WFR+) - Body ground | Always | 10 kΩ or higher |
| L30-30 (WFR-) - Body ground | Always | 10 kΩ or higher |
| L30-8 (WFL+) - Body ground | Always | 10 kΩ or higher |
| L30-23 (WFL-) - Body ground | Always | 10 kΩ or higher |
| L30-9 (FR+) - Body ground | Always | 10 kΩ or higher |
| L30-24 (FR-) - Body ground | Always | 10 kΩ or higher |
| L30-14 (FL+) - Body ground | Always | 10 kΩ or higher |
| L30-29 (FL-) - Body ground | Always | 10 kΩ or higher |
| L30-12 (RR+) - Body ground | Always | 10 kΩ or higher |
| L30-27 (RR-) - Body ground | Always | 10 kΩ or higher |
| L30-11 (RL+) - Body ground | Always | 10 kΩ or higher |
| L30-26 (RL-) - Body ground | Always | 10 kΩ or higher |
| L30-13 (TWR+) - Body ground | Always | 10 kΩ or higher |
| L30-28 (TWR-) - Body ground | Always | 10 kΩ or higher |
| L30-10 (TWL+) - Body ground | Always | 10 kΩ or higher |
| L30-25 (TWL-) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the front No. 1 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 4.6 to 6.6 Ω |
| *a | Component without harness connected
(Front No. 1 Speaker Assembly) |
OK
NG
Remove the front No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Front No. 2 Speaker Assembly) |
OK
NG
Remove the rear speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 5.2 Ω |
| *a | Component without harness connected
(Rear Speaker Assembly) |
OK
NG
Remove the rear No. 2 speaker assembly (See page Audio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Always | 3.2 to 4.8 Ω |
| *a | Component without harness connected
(Rear No. 2 Speaker Assembly) |
OK
NG