Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › 2014.11–2016.05
RM2070E _56 Audio / Visual / Telematics _061932 NAVIGATION / MULTI INFO DISPLAY _0301740 NAVIGATION SYSTEM(for Navigation Receiver Type) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  Data Signal Circuit between Navigation Receiver Assembly and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the navigation receiver assembly via this circuit.

WIRING DIAGRAM

E345575E21
0.896,0.646 1.479,0.938 0.583,0.292 10 false US1- 0.865,2.198 1.448,2.49 0.583,0.292 10 false USG1 0.427,2.677 1.01,2.969 0.583,0.292 10 false L174 0.427,2.854 1.615,3.313 1.188,0.458 10 false No. 1 Stereo Jack Adapter Assembly 2.448,3.271 5.115,3.625 2.667,0.354 10 false : Data Signal (USB Communication Line) 5.531,2.635 6.115,2.927 0.583,0.292 10 false L176 5.531,2.802 6.76,3.24 1.229,0.438 10 false Navigation Receiver Assembly 5.927,2.219 6.51,2.51 0.583,0.292 10 false USG1 3.271,1.76 4.031,2.094 0.76,0.333 10 false (Shielded) 1.333,0.531 1.917,0.823 0.583,0.292 10 false 2 1.344,1.302 1.927,1.594 0.583,0.292 10 false 3 1.354,2.104 1.938,2.396 0.583,0.292 10 false 5 0.885,1.448 1.469,1.74 0.583,0.292 10 false US1+ 5.938,0.646 6.521,0.938 0.583,0.292 10 false UDO- 5.917,1.448 6.5,1.74 0.583,0.292 10 false UDO+ 5.719,0.521 6.302,0.813 0.583,0.292 10 false 2 5.719,1.313 6.302,1.604 0.583,0.292 10 false 3 5.729,2.094 6.313,2.385 0.583,0.292 10 false 5

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
a.

Disconnect the L176 navigation receiver assembly connector.


b.

Disconnect the L174 No. 1 stereo jack adapter assembly connector.


c.
U191413E01
0.166,2.222 0.340,2.396 0.174,0.174 10 *b 1.538,2.255 1.955,2.407 0.417,0.151 10 L174 0.507,3.749 0.956,3.900 0.449,0.151 10 US1- 0.166,0.055 0.340,0.228 0.174,0.174 10 *a 1.538,0.199 1.899,0.351 0.362,0.151 10 L176 0.554,1.569 1.098,1.720 0.544,0.151 10 UDO+ 2.472,1.391 3.070,1.542 0.598,0.151 10 UDO- 1.572,1.432 1.083,1.639 false 1.839,1.432 2.455,1.461 false 2.45,3.588 2.904,3.740 0.454,0.151 10 US1+ 2.45,3.891 2.976,4.043 0.525,0.151 10 USG1 2.256,1.887 2.701,2.039 0.445,0.151 10 USG1 1.639,3.42 0.988,3.813 false 1.8,3.42 2.431,3.663 false 1.768,3.518 2.431,3.954 false 1.77,1.559 2.219,1.943 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L174-2 (US1-) - L176-2 (UDO-) Always Below 1 Ω
L174-3 (US1+) - L176-3 (UDO+) Always Below 1 Ω
L174-5 (USG1) - L176-5 (USG1) Always Below 1 Ω
L174-2 (US1-) - Body ground Always 10 kΩ or higher
L174-3 (US1+) - Body ground Always 10 kΩ or higher
L174-5 (USG1) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
*b Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR