PARKING ASSIST ECU
Disconnect the L64 parking assist ECU connector.
Measure the voltage and resistance of each terminal of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| L64-1 (+B) - L64-4 (GND1) | SB - W-B | Power source signal | Power switch off | 11 to 14 V |
| L64-4 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| L64-8 (IG) - L64-4 (GND1) | V - W-B | IG power source signal | Power switch on (IG) | 11 to 14 V |
| L64-9 (ACC) - L64-4 (GND1) | P - W-B | ACC power source signal | Power switch on (ACC) | 11 to 14 V |
| L64-11 (TX+) - L64-10 (TX-) | W - R | AVC-LAN communication signal | - | - |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the L64 parking assist ECU connector.
Measure the voltage and resistance, and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| L65-1 (CSB3) - L64-4 (GND1) | G - W-B | Power source to ultrasonic sensor | Power switch on (READY) | 7.2 to 8.8 V |
| L65-2 (CSG3) - L64-4 (GND1) | P - W-B | Ultrasonic sensor ground | Always | Below 1 Ω |
| L65-8 (HO1) - L64-4 (GND1)
*1 |
SB - W-B | Rear height control sensor signal output | Power switch off | Below 1 V |
| Power switch on (IG) | 0.5 to 5.25 V | |||
| L65-9 (HI1) - L64-4 (GND1) | Y - W-B | Rear height control sensor signal input | Power switch off | Below 1 V |
| Power switch on (IG) | 0.5 to 5.25 V | |||
| L65-14 (CB+) - L64-4 (GND1) | W - W-B | Power source to rear television camera | Power switch on (READY)
Reverse (R) selected |
5.8 to 7.0 V |
| L65-15 (CV+) - L64-4 (GND1) | R - W-B | Rear television camera display signal (NTSC) input | Power switch on (READY)
Reverse (R) selected Camera lens not covered, displaying an image |
Pulse generation
(See waveform 1) |
| Power switch on (READY)
Reverse (R) selected Camera lens covered, blacking out screen |
Pulse generation
(See waveform 2) |
|||
| L65-19 (LIN3) | GR | Ultrasonic sensor signal input and output | - | - |
| L65-26 (ISSW) - L64-4 (GND1) | R - W-B | Parking assist pre support signal input | Power switch on (READY)
Parking assist pre support switch assembly pushed in |
Below 1 V |
| Power switch on (READY)
Parking assist pre support switch assembly not pushed |
4.75 to 5.25 V | |||
| L65-27 (HBL+) - L64-4 (GND1)
*1 |
P - W-B | Rear height control sensor power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 4.75 to 5.25 V | |||
| L65-28 (HB+) - L64-4 (GND1)
*1 |
G - W-B | Rear height control sensor power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 4.75 to 5.25 V | |||
| L65-29 (HGND) - Body ground
*1 |
BE - Body ground | Rear height control sensor ground | Always | Below 1 Ω |
| L65-30 (HBE+) - L64-4 (GND1)
*2 |
L - W-B | Rear height control sensor power supply | Power switch off | Below 1 V |
| Power switch on (IG) | 4.75 to 5.25 V | |||
| L65-31 (HG1) - Body ground | Y - Body ground | Rear height control sensor ground | Always | Below 1 Ω |
| L65-37 (CGND) - L64-4 (GND1) | Shield - W-B | Rear television camera ground (shield) | Always | Below 1 V |
| L65-38 (CV-) - L64-4 (GND1) | B - W-B | Rear television camera ground | Always | Below 1 V |
| L65-39 (CANL) - L64-4 (GND1) | L - W-B | CAN communication signal | - | - |
| L65-40 (CANH) - L64-4 (GND1) | B - W-B | CAN communication signal | - | - |
| L136-1 (GVIF) | GR | Video signal (Digital) | - | - |
If the result is not as specified, the ECU may have a malfunction.
*1: for LED headlight
*2: for Halogen headlight
Reference (Oscilloscope waveform):
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
Waveform 1 (camera lens is not covered, displaying an image)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | L65-14 (CB+) - L64-4 (GND1) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (READY), reverse (R) selected |
The video waveform changes according to the image sent by the rear television camera assembly.
Waveform 2 (camera lens is covered, blacking out the screen)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | L65-14 (CB+) - L64-4 (GND1) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (READY), reverse (R) selected |
The video waveform changes according to the image sent by the rear television camera assembly.
| *a | Waveform 1 (camera lens not covered, displaying an image) |
| *b | Waveform 2 (camera lens covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
REAR TELEVISION CAMERA ASSEMBLY
Disconnect the V6 rear television camera assembly connector.
Measure the voltage of each terminal of the wire harness side connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V6-3 (CGND) - Body ground | W-B - Body ground | Ground | Always | Below 1 V |
| V6-4 (CB+) - V6-3 (CGND) | W - W-B | Power source | Power switch on (READY)
Reverse (R) selected |
5.8 to 7.0 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the V6 rear television camera assembly connector.
Check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V6-2 (CV+) - V6-1 (CV-) | R - B | Display signal | Power switch on (READY)
Reverse (R) selected Camera lens not covered, displaying an image |
Pulse generation
(See waveform 1) |
| Power switch on (READY)
Reverse (R) selected Camera lens covered, blacking out screen |
Pulse generation
(See waveform 2) |
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
If the result is not as specified, the camera may have a malfunction.
Reference (Oscilloscope waveform):
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
Waveform 1 (camera lens is not covered, displaying an image)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | V6-2 (CV+) - V6-1 (CV-) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (READY), reverse (R) selected |
The video waveform changes according to the image sent by the rear television camera assembly.
Waveform 2 (camera lens is covered, blacking out the screen)
| Item | Content |
|---|---|
| Terminal No. (Symbol) | V6-2 (CV+) - V6-1 (CV-) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Power switch on (READY), reverse (R) selected |
The video waveform changes according to the image sent by the rear television camera assembly.
| *a | Waveform 1 (camera lens not covered, displaying an image) |
| *b | Waveform 2 (camera lens covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
NAVIGATION ECU SUB-ASSEMBLY (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>TERMINALS OF ECU)
HEADLIGHT LEVELING ECU ASSEMBLY (for LED Headlight) (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU)