Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › INTELLIGENT PARKING ASSIST SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301741 INTELLIGENT PARKING ASSIST SYSTEM C

PARK ASSIST / MONITORING  INTELLIGENT PARKING ASSIST SYSTEM  C1611  ECU Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges that there is an internal malfunction as a result of its self check.

HINT:

The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.


DTC No. DTC Detection Condition Trouble Area
C1611 When one of the following conditions is met:
·

ROM/SUM check malfunction

·

Mirror check malfunction

·

High-speed RAM check malfunction

·

EEPROM (Initial read) malfunction

·

RAM check malfunction

·

CPU busy malfunction

·

CPU communication malfunction

·

Integer arithmetic malfunction

·

FPU calculation malfunction

·

ASIC output malfunction


Parking assist ECU

CAUTION / NOTICE / HINT

NOTICE:
·

When the "System initializing" message is displayed on the navigation ECU sub-assembly after the auxiliary battery cable has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the intelligent parking assist system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION).



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.


e.

Check the Data List for proper functioning of the following items.

IPA/Parking Assist Monitor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ROM/SUM Check Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
Mirror Check Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
High-Speed RAM Check Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
EEPROM Status (Initial read) Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
RAM Check Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
CPU Busy Status Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
CPU Communication Status Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
Integer Arithmetic Status Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
FPU Calculation Status Parking assist ECU information/OK or NG OK: Parking assist ECU is normal
NG: Parking assist ECU is abnormal
-
ASIC Output Status Output condition of camera display signal/OK or NG OK: Output condition of camera display signal is normal
NG: Output condition of camera display signal is abnormal
-

Result:
Result Proceed to
OK is displayed for all items. A
NG is displayed for EEPROM status (Initial read). A
NG is displayed for items other than EEPROM status (Initial read). B




A

2.ADJUST SETTINGS (PARKING ASSIST ECU INITIALIZATION)

B

2.ADJUST SETTINGS (PARKING ASSIST ECU INITIALIZATION)
HINT:
·

The parking assist ECU stores different types of information during initialization. If the parking assist ECU cannot read the stored information when it is activated, the parking assist ECU judges that there is an internal malfunction and stores this DTC.

·

If the parking assist ECU cannot read the stored information when it is activated, allowing the ECU to store the information again may return the system to normal.



a.

Use the transition of diagnosis screens (note which transition pattern occurs) to confirm if the parking assist ECU was able to properly store the information from initialization (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DIAGNOSIS SYSTEM).

HINT:

The procedure to make the parking assist ECU store the vehicle information differs when the parking assist ECU has stored the information (initialized) and when the information has not been stored (not initialized).



b.

Perform the following procedure depending on the memory conditions to register the vehicle information into the parking assist ECU.

Condition Procedure
Not initialized Parking assist ECU initialization (See page (Click here))
Initialized
·

Height control sensor vehicle height difference setting (See page (Click here))

·

Rear television camera optical axis adjustment (See page (Click here))

·

Steering angle setting (See page (Click here))





NEXT

3.CHECK DTC OUTPUT
3.CHECK DTC OUTPUT

b.

Check for DTCs (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>INTELLIGENT PARKING ASSIST SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1611 is output A
DTCs are not output B



HINT:
·

If DTC C1611 is output, perform the procedure to allow the parking assist ECU to store the vehicle information again.

·

If DTC C1611 is still output after performing the procedure to make the parking assist ECU store the vehicle information 3 times, replace the parking assist ECU.

·

If DTC C1611 is output frequently, replace the parking assist ECU even though the DTC is not output when rechecking for DTCs.




A

B

END