Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM › 2012.03–2014.11
RM2070E _56 Audio / Visual / Telematics _061933 PARK ASSIST / MONITORING _0301742 REAR VIEW MONITOR SYSTEM U

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  TERMINALS OF ECU  


REAR TELEVISION CAMERA ASSEMBLY


U191340E02
3.5,0.229 3.76,0.406 0.26,0.177 10 false V6

a.

Disconnect the V6 rear television camera assembly connector.


b.

Measure the voltage of each terminal of the wire harness side connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-3 (CGND) - Body ground W-B - Body ground Ground Always Below 1 V
V6-4 (CB+) - V6-3 (CGND) W - W-B Power source Within 60 seconds of turning the power switch on (ACC) 5.5 to 7.05 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the V6 rear television camera assembly connector.


d.

Check for pulses between each terminal of the connector.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V6-2 (CV+) - V6-1 (CV-) R - B Video signal Power switch on (READY)
Reverse (R) selected
Camera lens not covered, displaying an image
Pulse generation
(See waveform 1)
Power switch on (READY)
Reverse (R) selected
Camera lens covered, blacking out screen
Pulse generation
(See waveform 2)

If the result is not as specified, the rear television camera assembly may have a malfunction.


e.

Reference (Oscilloscope waveform):

E361811E01
1,2.333 1.167,2.333 1.167,2.333 1.26,1.781 false 1.667,2.333 1.5,2.333 1.5,2.333 1.365,1.677 false 4.5,2.25 4.667,2.25 4.667,2.25 4.729,1.635 false 5.167,2.25 5,2.25 5,2.25 4.865,1.563 false 0.448,0.292 0.76,0.49 0.313,0.198 10 false *a 3.99,0.219 4.302,0.417 0.313,0.198 10 false *b 0.5,1.219 0.865,1.417 0.365,0.198 10 false GND 0.813,2.25 1.125,2.448 0.313,0.198 10 false *c 1.698,2.26 2.01,2.458 0.313,0.198 10 false *d 3.948,1.229 4.313,1.427 0.365,0.198 10 false GND 5.208,2.167 5.521,2.365 0.313,0.198 10 false *d 4.323,2.167 4.635,2.365 0.313,0.198 10 false *c

i.

Waveform 1 (camera lens is not covered, displaying an image)

Item Content
Terminal No. (Symbol) V6-2 (CV+) - V6-1 (CV-)
Tool Setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (READY), reverse (R) selected

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.



ii.

Waveform 2 (camera lens is covered, blacking out the screen)

Item Content
Terminal No. (Symbol) V6-2 (CV+) - V6-1 (CV-)
Tool Setting 200 mV/DIV., 50 μs/DIV.
Condition Power switch on (READY), reverse (R) selected

HINT:

The video waveform changes according to the image sent by the rear television camera assembly.


Text in Illustration
*a Waveform 1 (camera lens not covered, displaying an image)
*b Waveform 2 (camera lens covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform