REAR TELEVISION CAMERA ASSEMBLY
Disconnect the V14 rear television camera assembly connector.
Measure the voltage on the wire harness side connector according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V14-6 (CB+) - Body ground | W - Body ground | Power source | Power switch on (ACC) | 5.5 to 7.05 V |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the V14 rear television camera assembly connector.
Measure the voltage and check for pulses at each terminal of the connector.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| V14-3 (CV+) - V14-2 (CV-) | R - B | Video signal | Power switch on (IG)
Reverse (R) selected Camera lens not covered, displaying an image |
Pulse generation
(Refer to waveform 1) |
| Power switch on (IG)
Reverse (R) selected Camera lens covered, blacking out screen |
Pulse generation
(Refer to waveform 2) |
|||
| V14-5 (CGND) - Body ground | W-B - Body ground | Shield ground | Always | Below 1 V |
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
If the result is not as specified, the rear television camera assembly may be malfunctioning.
Reference (Oscilloscope waveform):
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Waveform 1 (camera lens is not covered, displaying an image)
| Item | Content |
|---|---|
| Measurement terminal | V14-3 (CV+) - V14-2 (CV-) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Power switch on (IG), reverse (R) selected |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the power switch is on (ACC).
Waveform 2 (camera lens is covered, blacking out the screen)
| Item | Content |
|---|---|
| Measurement terminal | V14-3 (CV+) - V14-2 (CV-) |
| Measurement setting | 200 mV/DIV., 50 μs./DIV. |
| Condition | Power switch on (IG), reverse (R) selected |
The video waveform changes according to the image sent by the rear television camera assembly.
The video waveform is constantly output when the power switch is on (ACC).
| *a | Waveform 1 (camera lens is not covered, displaying an image) |
| *b | Waveform 2 (camera lens is covered, blacking out the screen) |
| *c | Synchronization Signal |
| *d | Video Waveform |
NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>TERMINALS OF ECU)
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type (w/o Navigation System)) (See page Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>TERMINALS OF ECU)
RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type (w/ Navigation System)) (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for Radio and Display Type)>TERMINALS OF ECU)