Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301753 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2785  Communication Malfunction between ECUs Connected by LIN  


DESCRIPTION

The certification ECU (smart key ECU assembly) monitors communication between all the ECUs connected to the certification bus lines. When the certification ECU (smart key ECU assembly) detects errors in communication with all the ECUs connected to the certification bus lines at a set interval and 3 times in a row, DTC B2785 will be stored.

DTC No. DTC Detection Condition Trouble Area
B2785
·

Errors in LIN communication between ECUs and an open or short in communication lines

·

LIN communication from the certification ECU (smart key ECU assembly) detects errors in communication 3 times in a row.


·

Certification ECU (smart key ECU assembly)

·

Transmission control ECU assembly

·

ID code box (immobiliser code ECU)

·

Wire harness or connector



WIRING DIAGRAM

B446203E05
4.563,3.729 6.344,4.458 1.781,0.729 10 false Transmission Control ECU Assembly 4.594,1.854 6.167,2.552 1.573,0.698 10 false Certification ECU (Smart Key ECU Assembly) 1.333,1.844 3.021,2.573 1.688,0.729 10 false ID Code Box (Immobiliser Code ECU) 0.906,4.292 2.896,4.677 1.99,0.385 10 false : LIN Communication Line 1.344,1.698 1.75,1.865 0.406,0.167 10 false L191 2.594,1.146 2.938,1.344 0.344,0.198 10 false LIN1 4.354,0.99 4.615,1.198 0.26,0.208 10 false 17 2.979,0.99 3.198,1.198 0.219,0.208 10 false 2 4.625,3 4.948,3.167 0.323,0.167 10 false LIN 4.625,1.125 4.948,1.292 0.323,0.167 10 false LIN 4.344,2.854 4.563,3.021 0.219,0.167 10 false 24 4.563,3.563 4.885,3.729 0.323,0.167 10 false A24 4.604,1.698 5,1.865 0.396,0.167 10 false L197

CAUTION / NOTICE / HINT

NOTICE:
·

If the certification ECU (smart key ECU assembly) is replaced, register the key.

·

If the transmission control ECU assembly is replaced, register the ECU code.

·

If the ID code box (immobiliser code ECU) is replaced, register the ECU code and ECU communication ID.

·

When using the GTS to troubleshoot with the power switch off:

Connect the GTS to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - EACH ECU)
a.

Disconnect the L197, L191 and A24 connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L197-17 (LIN) - A24-24 (LIN) Always Below 1 Ω
L197-17 (LIN) - L191-2 (LIN1) Always Below 1 Ω
L197-17 (LIN) - Body ground Always 10 kΩ or higher


Standard Voltage:
Tester Connection Condition Specified Condition
L197-17 (LIN) - Body ground Always Below 1 V




OK

2.CHECK DTC OUTPUT (TRANSMISSION CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK DTC OUTPUT (TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Reconnect the L197 and L191 connectors.



c.

Recheck for DTCs.

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B




A

3.CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))

B

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

3.CHECK DTC OUTPUT (ID CODE BOX (IMMOBILISER CODE ECU))
a.

Reconnect the A24 connector.


b.

Disconnect the L191 connector.



d.

Recheck for DTCs.

Result:
Result Proceed to
DTC B2785 is output A
DTC B2785 is not output B




A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE ID CODE BOX (IMMOBILISER CODE ECU)