Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN NO. 1 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 1 junction connector (engine room main wire side).

HINT:

The following tables contain information about the items and buses connected via junction connectors. The junction connector may be used for multiple separate buses. In this case, the name of the bus will be shown below the name of the item that terminals are connected to. The bus name will be shown in brackets (example: (for Sub bus 12)).


i.

Connection diagram

U154814E02
3.229,1.406 3.229,0.677 3.229,0.677 2.854,0.677 false 3.375,1.427 3.375,0.281 3.375,0.281 3.75,0.281 false 3.375,1.667 3.375,2.5 3.375,2.5 3.75,2.5 false 3.229,1.677 3.229,2.396 3.229,2.396 2.865,2.396 false 3.521,1.396 3.521,0.583 3.521,0.583 4.438,0.583 false 3.521,1.667 3.521,2.229 3.521,2.229 4.51,2.229 false 3.667,1.417 3.667,0.865 3.667,0.865 4.729,0.865 false 3.677,1.667 3.677,2.052 3.677,2.052 4.781,2.052 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.271,0.604 3.104,0.917 0.833,0.313 10 false CANH*b 2.313,2.313 3.146,2.625 0.833,0.313 10 false CANL*b 3.802,0.208 4.635,0.521 0.833,0.313 10 false CANH*c 3.781,2.427 4.615,2.74 0.833,0.313 10 false CANL*c 2.406,1.417 2.771,1.635 0.365,0.219 10 false A67 4.469,0.49 5.302,0.802 0.833,0.313 10 false CANH*d 4.531,2.146 5.365,2.458 0.833,0.313 10 false CANL*d 4.76,0.792 5.594,1.104 0.833,0.313 10 false CANH*e 4.813,1.969 5.646,2.281 0.833,0.313 10 false CANL*e

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 12)
*e to ECM
(for Sub Bus 12)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) P ECM
(for V bus)
A67-7 (CANL) V
A67-2 (CANH) LG Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A67-8 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 12)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 12)
A67-10 (CANL) W



b.

Check the CAN No. 1 junction connector (instrument panel wire side).

i.

Connection diagram

U154815E03
3.802,1.406 3.802,0.396 3.802,0.396 3.438,0.396 false 3.948,1.406 3.948,0.677 3.948,0.677 4.323,0.677 false 3.948,1.719 3.948,2.438 3.948,2.438 4.323,2.438 false 3.802,1.719 3.802,2.552 3.802,2.552 3.438,2.552 false 3.521,1.417 3.521,0.75 3.521,0.75 3.146,0.75 false 3.51,1.729 3.51,2.167 3.51,2.167 3.146,2.167 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.594,0.667 3.427,0.979 0.833,0.313 10 false CANH*b 2.604,2.094 3.438,2.406 0.833,0.313 10 false CANL*b 2.865,0.323 3.698,0.635 0.833,0.313 10 false CANH*c 2.875,2.479 3.469,2.698 0.594,0.219 10 false CANL*c 2.375,1.417 2.729,1.635 0.354,0.219 10 false L132 4.354,0.604 5.188,0.917 0.833,0.313 10 false CANH*d 4.354,2.354 5.188,2.667 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector
(for Sub Bus 12)
*c Main body ECU (Multiplex Network Body ECU)
(for V Bus)
*d to CAN No. 2 Junction Connector
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R CAN No. 5 junction connector
(for Sub bus 12)
L132-9 (CANL) Y
L132-5 (CANH) SB Main body ECU (Multiplex network body ECU)
(for V bus)
L132-11 (CANL) W
L132-6 (CANH) B CAN No. 2 junction connector
(for V bus)
L132-12 (CANL) W




CAN NO. 1 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 1 junction connector (engine room main wire side).

HINT:

The following tables contain information about the items and buses connected via junction connectors. The junction connector may be used for multiple separate buses. In this case, the name of the bus will be shown below the name of the item that terminals are connected to. The bus name will be shown in brackets (example: (for Sub bus 12)).


i.

Connection diagram

U191039E02
3.219,1.417 3.219,0.688 3.219,0.688 2.844,0.688 false 3.219,1.698 3.219,2.188 3.219,2.188 2.854,2.188 false 3.5,1.427 3.5,0.406 3.5,0.406 4.417,0.406 false 3.5,1.688 3.5,2.458 3.5,2.458 4.49,2.458 false 3.646,1.417 3.646,0.688 3.646,0.688 4.708,0.688 false 3.646,1.667 3.646,2.167 3.646,2.167 4.75,2.167 false 0.156,0.115 0.531,0.396 0.375,0.281 10 false *a 2.292,0.604 3.125,0.917 0.833,0.313 10 false CANH*b 2.323,2.104 3.156,2.417 0.833,0.313 10 false CANL*b 2.406,1.417 2.771,1.635 0.365,0.219 10 false A67 4.469,0.323 5.302,0.635 0.833,0.313 10 false CANH*c 4.542,2.375 5.375,2.688 0.833,0.313 10 false CANL*c 4.76,0.604 5.594,0.917 0.833,0.313 10 false CANH*d 4.802,2.083 5.635,2.396 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 12)
*d to ECM
(for Sub Bus 12)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) LG Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A67-7 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 12)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 12)
A67-10 (CANL) W



b.

Check the CAN No. 1 junction connector (instrument panel wire side).

i.

Connection diagram

U154815E03
3.802,1.406 3.802,0.396 3.802,0.396 3.438,0.396 false 3.948,1.406 3.948,0.677 3.948,0.677 4.323,0.677 false 3.948,1.719 3.948,2.438 3.948,2.438 4.323,2.438 false 3.802,1.719 3.802,2.552 3.802,2.552 3.438,2.552 false 3.521,1.417 3.521,0.75 3.521,0.75 3.146,0.75 false 3.51,1.729 3.51,2.167 3.51,2.167 3.146,2.167 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.594,0.667 3.427,0.979 0.833,0.313 10 false CANH*b 2.604,2.094 3.438,2.406 0.833,0.313 10 false CANL*b 2.865,0.323 3.698,0.635 0.833,0.313 10 false CANH*c 2.875,2.479 3.469,2.698 0.594,0.219 10 false CANL*c 2.375,1.417 2.729,1.635 0.354,0.219 10 false L132 4.354,0.604 5.188,0.917 0.833,0.313 10 false CANH*d 4.354,2.354 5.188,2.667 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector
(for Sub Bus 12)
*c to CAN No. 2 Junction Connector
(for V Bus)
*d Combination Meter Sub-assembly
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R CAN No. 5 junction connector
(for Sub bus 12)
L132-9 (CANL) Y
L132-5 (CANH) GR CAN No. 2 junction connector
(for V bus)
L132-11 (CANL) W
L132-6 (CANH) SB Combination meter sub-assembly
(for V bus)
L132-12 (CANL) G




CAN NO. 2 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 2 junction connector (instrument panel connector holder left side).

i.

Connection diagram

U154779E02
2.75,0.938 2.906,0.938 2.906,0.938 3.448,1.354 false 2.75,1.573 2.906,1.573 2.906,1.573 3.438,1.677 false 4.313,0.958 4.208,0.958 4.208,0.958 3.615,1.365 false 4.333,1.531 4.073,1.531 4.073,1.531 3.615,1.656 false 2.75,1.271 2.875,1.271 2.875,1.271 3.448,1.521 false 4.333,1.24 4.24,1.24 4.24,1.24 3.615,1.5 false 2.75,1.885 2.969,1.885 2.969,1.885 3.438,1.823 false 4.323,1.938 4.115,1.938 4.115,1.938 3.625,1.833 false 4.354,0.875 4.938,1.177 0.583,0.302 10 false CANH*b 4.354,1.469 4.938,1.771 0.583,0.302 10 false CANH*d 2.198,0.844 2.781,1.146 0.583,0.302 10 false CANL*b 4.354,1.167 4.938,1.469 0.583,0.302 10 false CANH*c 2.198,1.177 2.781,1.479 0.583,0.302 10 false CANL*c 2.198,1.49 2.781,1.792 0.583,0.302 10 false CANL*d 4.354,1.875 4.938,2.177 0.583,0.302 10 false CANH*e 2.198,1.823 2.781,2.125 0.583,0.302 10 false CANL*e 0.052,0 0.531,0.5 0.479,0.5 10 false *a 3.531,0.563 3.896,0.74 0.365,0.177 10 false L94

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
(for V Bus)
*c to CAN No. 1 Junction Connector
(for V Bus)
*d to Certification ECU (Smart Key ECU Assembly)
(for V Bus)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-2 (CANH) GR CAN No. 3 junction connector
(for V bus)
L94-1 (CANL) W
L94-5 (CANH) B CAN No. 1 junction connector
(for V bus)
L94-4 (CANL) W
L94-8 (CANH) B Certification ECU (Smart key ECU assembly)
(for V bus)
L94-7 (CANL) W
L94-11 (CANH) B Spiral cable with sensor sub-assembly (Steering angle sensor)
(for V bus)
L94-10 (CANL) W



b.

Check the CAN No. 2 junction connector (instrument panel connector holder right side).

i.

Connection diagram

U154780E03
2.531,0.875 2.792,0.875 2.792,0.875 3.563,1.344 false 2.531,1.49 3.052,1.49 3.052,1.49 3.552,1.667 false 4.229,0.927 3.99,0.927 3.99,0.927 3.698,1.333 false 4.25,1.531 3.854,1.531 3.854,1.531 3.729,1.646 false 2.531,1.198 2.958,1.198 2.958,1.198 3.563,1.5 false 4.25,1.229 4.01,1.229 4.01,1.229 3.729,1.49 false 2.542,2 2.906,2 2.906,2 3.563,1.844 false 4.24,1.927 3.885,1.927 3.885,1.927 3.719,1.844 false 2.531,2.344 3.104,2.344 3.104,2.344 3.583,1.99 false 4.24,2.25 3.844,2.25 3.844,2.25 3.698,1.99 false 4.281,0.844 4.865,1.146 0.583,0.302 10 false CANL*b 4.281,1.448 4.865,1.75 0.583,0.302 10 false CANL*d 1.938,0.781 2.521,1.083 0.583,0.302 10 false CANH*b 4.281,1.167 4.865,1.469 0.583,0.302 10 false CANL*c 1.938,1.115 2.521,1.417 0.583,0.302 10 false CANH*c 1.938,1.417 2.521,1.719 0.583,0.302 10 false CANH*d 4.281,1.854 4.865,2.156 0.583,0.302 10 false CANL*e 4.281,2.198 4.865,2.5 0.583,0.302 10 false CANL*f 1.969,1.917 2.552,2.219 0.583,0.302 10 false CANH*e 1.979,2.271 2.563,2.573 0.583,0.302 10 false CANH*f 0.052,0 0.417,0.375 0.365,0.375 10 false *a 3.49,0.563 3.906,0.802 0.417,0.24 10 false L95

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
(for V Bus)
*c to Yaw Rate Sensor
(for V Bus)
*d to Airbag ECU Assembly
(for V Bus)
*e to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for V Bus)
*f to DLC3
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-2 (CANH) R Power steering ECU assembly
(for V bus)
L95-3 (CANL) W
L95-5 (CANH) B Yaw rate sensor
(for V bus)
L95-6 (CANL) W
L95-8 (CANH) B Airbag ECU assembly
(for V bus)
L95-9 (CANL) W
L95-11 (CANH) B Radio and display receiver assembly*
(for V bus)
L95-12 (CANL) W
L95-14 (CANH) B DLC3
(for V bus)
L95-15 (CANL) W

*: for Radio and Display Type




CAN NO. 2 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 2 junction connector (instrument panel connector holder left side).

i.

Connection diagram

U191020E02
2.75,0.927 2.906,0.927 2.906,0.927 3.448,1.344 false 2.75,1.563 2.906,1.563 2.906,1.563 3.438,1.667 false 4.302,0.948 4.198,0.948 4.198,0.948 3.604,1.354 false 4.323,1.542 4.063,1.542 4.063,1.542 3.604,1.667 false 2.74,1.25 2.865,1.25 2.865,1.25 3.438,1.5 false 4.313,1.24 4.219,1.24 4.219,1.24 3.594,1.5 false 2.76,1.906 2.979,1.906 2.979,1.906 3.448,1.844 false 4.302,1.938 4.094,1.938 4.094,1.938 3.604,1.833 false 4.365,0.865 4.948,1.167 0.583,0.302 10 false CANL*b 4.354,1.458 4.938,1.76 0.583,0.302 10 false CANL*d 2.198,0.833 2.781,1.135 0.583,0.302 10 false CANH*b 4.365,1.156 4.948,1.458 0.583,0.302 10 false CANL*c 2.198,1.156 2.781,1.458 0.583,0.302 10 false CANH*c 2.198,1.479 2.781,1.781 0.583,0.302 10 false CANH*d 4.354,1.854 4.938,2.156 0.583,0.302 10 false CANL*e 2.208,1.813 2.792,2.115 0.583,0.302 10 false CANH*e 0.177,0.094 0.656,0.594 0.479,0.5 10 false *a 3.51,0.563 3.875,0.74 0.365,0.177 10 false L94

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
(for V Bus)
*c to CAN No. 3 Junction Connector
(for V Bus)
*d to Certification ECU (Smart Key ECU Assembly)
(for V Bus)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-1 (CANH) GR CAN No. 1 junction connector
(for V bus)
L94-2 (CANL) W
L94-4 (CANH) B CAN No. 3 junction connector
(for V bus)
L94-5 (CANL) W
L94-7 (CANH) B Certification ECU (Smart key ECU assembly)
(for V bus)
L94-8 (CANL) W
L94-10 (CANH) B Spiral cable with sensor sub-assembly (Steering angle sensor)
(for V bus)
L94-11 (CANL) W



b.

Check the CAN No. 2 junction connector (instrument panel connector holder right side).

i.

Connection diagram

U191021E02
2.531,0.865 2.792,0.865 2.792,0.865 3.563,1.333 false 2.531,1.469 3.052,1.469 3.052,1.469 3.552,1.646 false 4.229,0.927 3.99,0.927 3.99,0.927 3.698,1.333 false 4.25,1.531 3.854,1.531 3.854,1.531 3.729,1.646 false 2.531,1.198 2.958,1.198 2.958,1.198 3.563,1.5 false 4.25,1.24 4.01,1.24 4.01,1.24 3.729,1.5 false 2.542,2.01 2.906,2.01 2.906,2.01 3.563,1.854 false 4.24,1.958 3.885,1.958 3.885,1.958 3.719,1.875 false 2.531,2.365 3.104,2.365 3.104,2.365 3.583,2.01 false 4.24,2.271 3.844,2.271 3.844,2.271 3.698,2.01 false 4.281,0.833 4.865,1.135 0.583,0.302 10 false CANH*b 4.281,1.448 4.865,1.75 0.583,0.302 10 false CANH*d 1.99,0.76 2.573,1.063 0.583,0.302 10 false CANL*b 4.281,1.156 4.865,1.458 0.583,0.302 10 false CANH*c 2,1.083 2.583,1.385 0.583,0.302 10 false CANL*c 1.99,1.365 2.573,1.667 0.583,0.302 10 false CANL*d 4.281,1.875 4.865,2.177 0.583,0.302 10 false CANH*e 4.281,2.198 4.865,2.5 0.583,0.302 10 false CANH*f 2,1.906 2.583,2.208 0.583,0.302 10 false CANL*e 2.021,2.271 2.604,2.573 0.583,0.302 10 false CANL*f 0.156,0.125 0.521,0.5 0.365,0.375 10 false *a 3.49,0.563 3.906,0.802 0.417,0.24 10 false L95

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
(for V Bus)
*c to Yaw Rate Sensor
(for V Bus)
*d to Airbag ECU Assembly
(for V Bus)
*e
·

to Navigation Receiver Assembly

(for Navigation Receiver Type)

·

to Radio and Display Receiver Assembly

(for Radio and Display Type)


(for V Bus)
*f to DLC3
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-3 (CANH) R Power steering ECU assembly
(for V bus)
L95-2 (CANL) W
L95-6 (CANH) B Yaw rate sensor
(for V bus)
L95-5 (CANL) W
L95-9 (CANH) B Airbag ECU assembly
(for V bus)
L95-8 (CANL) W
L95-12 (CANH) B
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


(for V bus)
L95-11 (CANL) W
L95-15 (CANH) B DLC3
(for V bus)
L95-14 (CANL) W

*1: for Navigation Receiver Type

*2: for Radio and Display Type




CAN NO. 3 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 3 junction connector (engine room main wire side).

i.

Connection diagram

U154816E02
3.229,1.417 3.229,0.688 3.229,0.688 2.854,0.688 false 3.229,1.698 3.229,2.417 3.229,2.417 2.865,2.417 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.271,0.615 3.104,0.927 0.833,0.313 10 false CANH*b 2.313,2.333 3.146,2.646 0.833,0.313 10 false CANL*b 2.406,1.396 2.771,1.615 0.365,0.219 10 false A68

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Transmission Control ECU Assembly
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) Y Transmission control ECU assembly
(for V bus)
A68-7 (CANL) BR



b.

Check the CAN No. 3 junction connector (instrument panel wire side).

i.

Connection diagram

U154817E03
3.667,1.427 3.667,0.698 3.667,0.698 3.292,0.698 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 3.813,1.698 3.813,2.417 3.813,2.417 4.177,2.417 false 3.667,1.688 3.667,2.406 3.667,2.406 3.292,2.406 false 4,1.448 4.281,1.333 4.281,1.333 4.427,1.333 false 4.01,1.656 4.292,1.771 4.292,1.771 4.448,1.771 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.708,0.615 3.542,0.927 0.833,0.313 10 false CANH*b 2.74,2.323 3.573,2.635 0.833,0.313 10 false CANL*b 4.24,0.604 5.073,0.917 0.833,0.313 10 false CANH*c 4.219,2.354 5.052,2.667 0.833,0.313 10 false CANL*c 2.385,1.417 2.802,1.635 0.417,0.219 10 false L133 4.458,1.24 5.167,1.458 0.708,0.219 10 false CANH*d 4.469,1.698 5.083,1.938 0.615,0.24 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Power Management Control ECU
(for V Bus)
*c to CAN No. 2 Junction Connector
(for V Bus)
*d to Combination Meter Sub-assembly
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Power management control ECU
(for V bus)
L133-10 (CANL) P
L133-5 (CANH) GR CAN No. 2 junction connector
(for V bus)
L133-11 (CANL) W
L133-6 (CANH) SB Combination meter sub-assembly
(for V bus)
L133-12 (CANL) G




CAN NO. 3 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 3 junction connector (engine room main wire side).

i.

Connection diagram

U191040E02
3.208,1.406 3.208,0.677 3.208,0.677 2.833,0.677 false 3.219,1.677 3.219,2.396 3.219,2.396 2.854,2.396 false 3.365,1.406 3.365,0.677 3.365,0.677 3.729,0.677 false 3.365,1.677 3.365,2.396 3.365,2.396 3.729,2.396 false 0.104,0.042 0.479,0.323 0.375,0.281 10 false *a 2.292,0.583 3.125,0.896 0.833,0.313 10 false CANH*b 2.313,2.302 3.146,2.615 0.833,0.313 10 false CANL*b 2.406,1.406 2.771,1.625 0.365,0.219 10 false A68 3.781,0.594 4.344,0.906 0.563,0.313 10 false CANH*c 3.781,2.313 4.344,2.625 0.563,0.313 10 false CANL*c

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b ECM
(for V Bus)
*c to Transmission Control ECU Assembly
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) P ECM
(for V bus)
A68-7 (CANL) V
A68-2 (CANH) Y Transmission control ECU assembly
(for V bus)
A68-8 (CANL) BR



b.

Check the CAN No. 3 junction connector (instrument panel wire side).

i.

Connection diagram

U154817E03
3.667,1.427 3.667,0.698 3.667,0.698 3.292,0.698 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 3.813,1.698 3.813,2.417 3.813,2.417 4.177,2.417 false 3.667,1.688 3.667,2.406 3.667,2.406 3.292,2.406 false 4,1.448 4.281,1.333 4.281,1.333 4.427,1.333 false 4.01,1.656 4.292,1.771 4.292,1.771 4.448,1.771 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.708,0.615 3.542,0.927 0.833,0.313 10 false CANH*b 2.74,2.323 3.573,2.635 0.833,0.313 10 false CANL*b 4.24,0.604 5.073,0.917 0.833,0.313 10 false CANH*c 4.219,2.354 5.052,2.667 0.833,0.313 10 false CANL*c 2.385,1.417 2.802,1.635 0.417,0.219 10 false L133 4.458,1.24 5.167,1.458 0.708,0.219 10 false CANH*d 4.469,1.698 5.083,1.938 0.615,0.24 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Power Management Control ECU
(for V Bus)
*c to Main body ECU (Multiplex Network Body ECU)
(for V Bus)
*d to CAN No. 2 Junction Connector
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Power management control ECU
(for V bus)
L133-10 (CANL) P
L133-5 (CANH) SB Main body ECU (Multiplex network body ECU)
(for V bus)
L133-11 (CANL) W
L133-6 (CANH) B CAN No. 2 junction connector
(for V bus)
L133-12 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR


a.

Check the No. 4 CAN junction connector.

HINT:
·

Distinguish between the connectors connected to the No. 4 CAN junction connector by checking the color of the communication wire.

·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



i.

Connection diagram

C423692C13
0.792,1.104 0.969,1.104 0.969,1.104 1.323,1.354 true 0.844,1.719 1.031,1.719 1.031,1.719 1.323,1.563 true 0.542,0.656 0.854,0.854 0.313,0.198 10 false *a 0.448,1.667 1.052,1.875 0.604,0.208 10 false CANH 0.438,1.063 0.948,1.271 0.51,0.208 10 false CANL 2.781,0.646 3.094,0.844 0.313,0.198 10 false *b
*a Vehicle wire harness connector
connected to CAN junction connector
*b Rear view of wire harness connector
(to No. 4 CAN Junction Connector)




b.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L185-1 (CANH) B Lane departure warning camera*1
(for Sub bus 11)
L185-2 (CANL) W
L184-1 (CANH) B Power management control ECU
(for Sub bus 11)
L184-2 (CANL) G
L183-1 (CANH) B Parking assist ECU*2
(for Sub bus 11)
L183-2 (CANL) L
L182-1 (CANH) B Driving support ECU assembly*3
(for Sub bus 11)
L182-2 (CANL) R
L181-1 (CANH) B CAN No. 1 junction terminal
(for Sub bus 11)
L181-2 (CANL) Y

·

*1: w/ Lane Departure Alert System

·

*2: w/ Intelligent Parking Assist System

·

*3: w/ Pre-crash Safety System




CAN NO. 5 JUNCTION CONNECTOR


a.

Check the CAN No. 5 junction connector (instrument panel connector holder left side).

i.

Connection diagram

U154818E02
3.385,1.406 3.385,0.271 3.385,0.271 3.01,0.271 false 3.229,1.427 3.229,0.604 3.229,0.604 2.865,0.604 false 3.521,1.427 3.521,0.281 3.521,0.281 3.896,0.281 false 3.667,1.427 3.667,0.604 3.667,0.604 4.031,0.604 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.427,0.198 3.26,0.51 0.833,0.313 10 false CANH*c 3.927,0.198 4.76,0.51 0.833,0.313 10 false CANL*b 2.385,1.406 2.75,1.625 0.365,0.219 10 false L101 2.281,0.521 3.115,0.833 0.833,0.313 10 false CANH*b 4.063,0.531 4.896,0.844 0.833,0.313 10 false CANL*c

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Air Conditioning Amplifier Assembly
(for Sub Bus 12)
*c to CAN No. 1 Junction Connector
(for Sub Bus 12)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L101-1 (CANH) B Air conditioning amplifier assembly
(for Sub bus 12)
L101-3 (CANL) W
L101-2 (CANH) R CAN No. 1 junction connector
(for Sub bus 12)
L101-4 (CANL) Y



b.

Check the CAN No. 5 junction connector (instrument panel connector holder right side).

i.

Connection diagram

U154819E02
3.521,1.406 3.521,0.688 3.521,0.688 3.156,0.688 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 4.229,0.615 5.063,0.927 0.833,0.313 10 false CANH*b 2.594,0.594 3.427,0.906 0.833,0.313 10 false CANL*b 2.385,1.406 2.792,1.625 0.406,0.219 10 false L102

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Power Management Control ECU
(for Sub Bus 12)


ii.

Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L102-5 (CANH) B Power management control ECU
(for Sub bus 12)
L102-3 (CANL) W




CAN No. 1 JUNCTION TERMINAL


a.

Check the CAN No. 1 junction terminal.

i.
U190994E02
0.948,0.844 0.646,0.844 0.646,0.844 0.646,2.177 false 1.24,1.177 0.938,1.177 0.938,1.177 0.938,2.167 false 0.177,0.094 0.333,0.271 0.156,0.177 10 false *a 1,0.76 1.573,0.917 0.573,0.156 10 false CANH*b 1.292,1.104 1.854,1.26 0.563,0.156 10 false CANL*b 1.823,2.156 2.208,2.323 0.385,0.167 10 false L180

Connection diagram

Text in Illustration
*a Rear view of wire harness connector
(to CAN No. 1 Junction Terminal)
*b to CAN No. 4 Junction Connector
(for Sub Bus 11)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
L180-3 (CANH) B CAN No. 4 junction connector
(for Sub bus 11)
L180-2 (CANL) Y




DLC3


a.

Measure the resistance according to the value(s) in the table below.

U154710E01
0.269,0.211 0.787,0.374 0.518,0.163 10 *1 1.574,1.596 1.848,1.768 0.274,0.172 10 L61 4.207,1.94 4.493,2.319 false 3.362,2.342 3.815,2.504 0.453,0.163 10 CANL 4.251,0.719 4.704,0.881 0.453,0.163 10 CANH 4.262,0.869 3.834,1.391 false 3.071,0.869 3.499,1.391 false 4.389,2.342 4.740,2.504 0.351,0.163 10 BAT 2.842,0.719 3.192,0.881 0.351,0.163 10 CG 3.862,1.94 3.576,2.319 false

Text in Illustration
*1 DLC3 - -

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L61-6 (CANH) - L61-14 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L61-6 (CANH) - L61-4 (CG) B - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-14 (CANL) - L61-4 (CG) W - G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-6 (CANH) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L61-14 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER MANAGEMENT CONTROL ECU


U154685E02
3.875,1.521 3.813,1.521 3.813,1.521 3.906,1.188 false 3.635,1.521 3.677,1.521 3.677,1.521 3.802,1.188 false 4.427,0.292 5.125,1.156 false 4.948,0.271 5.146,0.99 false 5.438,0.271 5.26,0.99 false 5.885,0.292 5.292,1.156 false 1.427,0.156 1.719,0.333 0.292,0.177 10 false A21 2.781,0.167 3.083,0.344 0.302,0.177 10 false A22 4.542,1.49 4.75,1.667 0.208,0.177 10 false L5 5.573,1.479 5.781,1.656 0.208,0.177 10 false L6 3.26,1.458 3.646,1.625 0.385,0.167 10 false CA2L 3.896,1.448 4.313,1.615 0.417,0.167 10 false CA2H 4.24,0.094 4.656,0.26 0.417,0.167 10 false CA3P 4.74,0.094 5.156,0.26 0.417,0.167 10 false CA1H 5.229,0.083 5.646,0.25 0.417,0.167 10 false CA1L 5.719,0.094 6.135,0.26 0.417,0.167 10 false CA3N 0.073,0 0.406,0.26 0.333,0.26 10 false *a

Text in Illustration
*a Component without harness connected
(Power Management Control ECU)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154241E02
1.823,2.573 1.458,2.635 false 1.823,2.365 1.458,2.188 false 1.865,2.573 1.573,3.031 false 2.542,2.271 2.25,2.354 false 2.073,3.063 2.281,3.24 0.208,0.177 10 false L5 1.063,2.552 1.427,2.729 0.365,0.177 10 false CA2L 2.583,2.188 2.979,2.365 0.396,0.177 10 false AM22 1.229,3.042 1.615,3.219 0.385,0.177 10 false CA2H 0.146,0.052 0.656,0.302 0.51,0.25 10 false *a 1.24,2.052 1.448,2.229 0.208,0.177 10 false E1

Disconnect the L5 power management control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Sub Bus 11 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L5-34 (CA2H) - L5-35 (CA2L) B - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L5-34 (CA2H) - L5-6 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L5-35 (CA2L) - L5-6 (E1) G - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L5-34 (CA2H) - L5-1 (AM22) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L5-35 (CA2L) - L5-1 (AM22) G - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.
U154250E02
2.469,2.5 1.646,2.208 false 2.417,2.5 1.667,2.448 false 2.427,2.354 2.104,2.094 false 2.635,2.365 3.021,2.083 false 1.698,2.771 2.417,2.573 false 1.75,3.052 2.469,2.573 false 2.594,3.01 2.865,3.208 0.271,0.198 10 false L6 1.281,2.094 1.646,2.271 0.365,0.177 10 false CA1L 1.271,2.344 1.656,2.521 0.385,0.177 10 false CA1H 1.302,2.688 1.688,2.865 0.385,0.177 10 false CA3P 1.344,3.01 1.729,3.188 0.385,0.177 10 false CA3N 0.146,0.115 0.469,0.396 0.323,0.281 10 false *a 1.719,1.958 2.094,2.135 0.375,0.177 10 false AM21 3.063,1.958 3.323,2.135 0.26,0.177 10 false E12

Disconnect the L6 power management control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-25 (CA1H) - L6-24 (CA1L) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L6-25 (CA1H) - L6-4 (E12) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-24 (CA1L) - L6-4 (E12) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-25 (CA1H) - L6-7 (AM21) V - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-24 (CA1L) - L6-7 (AM21) P - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 12 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L6-31 (CA3P) - L6-4 (E12) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-30 (CA3N) - L6-4 (E12) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-31 (CA3P) - L6-7 (AM21) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-30 (CA3N) - L6-7 (AM21) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


U155205E03
5.5,0.219 5.802,0.948 false 6.25,0.219 5.958,0.948 false 5.135,0.5 5.771,1.135 false 6.615,0.5 5.969,1.135 false 5.25,0.042 5.646,0.198 0.396,0.156 10 false CANL 6.125,0.052 6.552,0.208 0.427,0.156 10 false CANN 4.875,0.323 5.302,0.479 0.427,0.156 10 false CANH 6.49,0.323 6.917,0.479 0.427,0.156 10 false CANP 2.302,2.479 2.604,2.635 0.302,0.156 10 false D28 5.542,2.479 5.844,2.635 0.302,0.156 10 false A57 0.094,0.021 0.469,0.365 0.375,0.344 10 false *a

Text in Illustration
*a Component without harness connected
(ECM)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A57 and D28 ECM connectors.

U154723E01
0.18,0.166 0.643,0.516 0.462,0.349 10 *a 3.109,1.531 3.405,1.704 0.296,0.172 10 D28 5.113,1.799 5.399,2.364 false 2.207,0.746 2.660,0.909 0.453,0.163 10 CANL 2.26,2.159 2.713,2.322 0.453,0.163 10 CANH 0.826,2.138 1.223,2.301 0.397,0.163 10 BATT 5.335,2.366 5.580,2.528 0.244,0.163 10 E1 0.517,1.514 0.848,1.686 0.331,0.172 10 A57 1.644,1.496 1.213,2.114 false 1.328,2.16 1.731,2.341 0.403,0.181 10 CANP 1.126,0.743 1.536,0.924 0.411,0.181 10 CANN 1.964,1.352 2.19,0.896 false 1.893,1.352 1.554,0.901 false 1.976,1.414 2.249,2.141 false 1.897,1.426 1.726,2.141 false

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-13 (CANH) - D28-104 (E1) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-5 (CANL) - D28-104 (E1) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-13 (CANH) - A57-20 (BATT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-5 (CANL) - A57-20 (BATT) V - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 12 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-12 (CANP) - D28-104 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-4 (CANN) - D28-104 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-12 (CANP) - A57-20 (BATT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-4 (CANN) - A57-20 (BATT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TRANSMISSION CONTROL ECU ASSEMBLY


U154743E01
4.222,0.473 4.486,0.654 0.264,0.181 10 A24 2.637,0.473 2.901,0.654 0.264,0.181 10 A23 3.238,2.107 3.653,2.272 0.415,0.165 10 CA1H 4.143,2.093 4.532,2.250 0.389,0.157 10 CA1L 3.64,2.172 3.693,2.172 3.693,2.172 3.844,1.612 false 4.143,2.169 4.097,2.169 4.097,2.169 3.957,1.618 false 0.074,0.045 0.278,0.220 0.204,0.175 10 *a

Text in Illustration
*a Component without harness connected
(Transmission Control ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154768E02
2.073,1.688 1.802,2.156 false 2.167,1.698 2.438,2.177 false 2.104,3.719 2.521,4.146 false 1.208,1.354 0.906,0.99 false 0.052,0 0.406,0.375 0.354,0.375 10 false *a 0.5,1.448 0.927,1.792 0.427,0.344 10 false A24 0.51,3.51 0.927,3.844 0.417,0.333 10 false A23 2.479,2.198 2.885,2.375 0.406,0.177 10 false CA1H 1.406,2.198 1.792,2.375 0.385,0.177 10 false CA1L 2.552,4.156 2.927,4.333 0.375,0.177 10 false BATT 0.677,0.792 0.865,0.969 0.188,0.177 10 false E1

Disconnect the A23 and A24 transmission control ECU assembly connectors.

Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-16 (CA1H) - A24-15 (CA1L) Y - BR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A24-16 (CA1H) - A24-1 (E1) Y - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-15 (CA1L) - A24-1 (E1) BR - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-16 (CA1H) - A23-15 (BATT) Y - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A24-15 (CA1L) - A23-15 (BATT) BR - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154754E02
2.656,1.729 2.948,1 false 1.115,2.688 1.656,2.135 false 1.615,2.677 1.76,2.135 false 1.958,2.125 2.042,2.667 false 2.063,2.125 2.448,2.667 false 2.646,2.042 2.948,2.802 false 0.198,0.156 0.469,0.406 0.271,0.25 10 false *a 0.271,0.885 0.563,1.042 0.292,0.156 10 false A58 2.938,0.823 3.167,0.979 0.229,0.156 10 false BS 2.927,2.813 3.25,2.99 0.323,0.177 10 false GND 0.771,2.708 1.135,2.885 0.365,0.177 10 false CA2L 1.302,2.698 1.688,2.875 0.385,0.177 10 false CA2H 1.802,2.708 2.188,2.885 0.385,0.177 10 false CA1H 2.333,2.698 2.698,2.875 0.365,0.177 10 false CA1L

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-37 (CA1H) - A58-38 (CA1L) LG - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-37 (CA1H) - A58-28 (GND) LG - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-38 (CA1L) - A58-28 (GND) L - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-37 (CA1H) - A58-15 (BS) LG - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-38 (CA1L) - A58-15 (BS) L - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 12 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-35 (CA2H) - A58-28 (GND) P - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-34 (CA2L) - A58-28 (GND) V - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-35 (CA2H) - A58-15 (BS) P - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-34 (CA2L) - A58-15 (BS) V - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


U191450E01
2.594,0.495 2.867,0.651 0.272,0.156 10 L16 3.936,0.495 4.208,0.651 0.272,0.156 10 R1 4.819,0.495 5.091,0.651 0.272,0.156 10 S1 2.647,2.359 3.058,2.514 0.411,0.156 10 CANH 3.14,1.642 2.865,2.346 false 3.324,2.359 3.735,2.514 0.411,0.156 10 CANL 3.311,1.925 3.503,2.346 false 0.14,0.106 0.399,0.365 0.259,0.259 10 *a

Text in Illustration
*a Component without harness connected
(Airbag ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L16 airbag ECU assembly connector.

U191001E02
1.208,1.156 1.5,1.635 false 1.417,1.854 1.198,2.323 false 1.688,1.875 1.604,2.229 false 5.719,1.938 5.927,2.344 false 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 0.99,2.333 1.438,2.5 0.448,0.167 10 false CANL 1,1 1.448,1.167 0.448,0.167 10 false CANH 1.521,2.26 1.719,2.427 0.198,0.167 10 false E1 5.854,2.354 6.208,2.521 0.354,0.167 10 false BAT 0.625,1.594 1.073,1.885 0.448,0.292 10 false L16 3.396,0.156 3.896,0.323 0.5,0.167 10 false *1 3.396,1.635 3.823,1.906 0.427,0.271 10 false L61

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L16-13 (CANH) - L16-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L16-13 (CANH) - L16-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-22 (CANL) - L16-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-13 (CANH) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L16-22 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U191257E02
1.74,0.573 1.594,0.573 1.594,0.573 1.594,0.854 false 1.552,1.469 1.458,1.469 1.458,1.469 1.458,3.229 false 0.656,2.667 1.031,2.667 false 1.906,4.917 1.76,4.917 1.76,4.917 1.76,4.625 false 1.521,4.917 1.667,4.917 1.667,4.917 1.667,4.625 false 3.406,7.885 3.667,8.042 0.26,0.156 10 false MB 5.031,6.625 5.292,6.781 0.26,0.156 10 false 2A 1.781,6.583 2.042,6.74 0.26,0.156 10 false 2B 5.052,5.25 5.313,5.406 0.26,0.156 10 false 2C 1.792,5.271 2.052,5.427 0.26,0.156 10 false 2D 4.688,3.979 4.948,4.135 0.26,0.156 10 false 2E 4.979,3.958 5.24,4.198 0.26,0.24 10 false *A 5.646,3.958 5.906,4.167 0.26,0.208 10 false *B 5.365,3.969 5.625,4.125 0.26,0.156 10 false 2F 1.823,3.938 2.083,4.094 0.26,0.156 10 false L7 0.208,2.448 0.469,2.604 0.26,0.156 10 false 2E 0.521,2.448 0.802,2.688 0.281,0.24 10 false *A 0.51,2.74 0.802,2.979 0.292,0.24 10 false *B 0.219,2.729 0.479,2.885 0.26,0.156 10 false 2F 0.427,1.302 0.688,1.458 0.26,0.156 10 false 2D 0.406,2.042 0.667,2.198 0.26,0.156 10 false 2C 1.938,1.438 2.198,1.594 0.26,0.156 10 false L7 1.771,0.49 1.927,0.646 0.156,0.156 10 false *1 3.708,0.542 3.969,0.698 0.26,0.156 10 false MB 6.344,2.083 6.604,2.24 0.26,0.156 10 false 2A 6.344,1.396 6.604,1.552 0.26,0.156 10 false 2B 0.365,0.104 0.625,0.302 0.26,0.198 10 false *a 1.385,3.25 1.542,3.406 0.156,0.156 10 false *2 1.948,4.844 2.521,5 0.573,0.156 10 false CANL 1.104,4.844 1.677,5 0.573,0.156 10 false CANH

Text in Illustration
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) *2 1 connector
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -

U190876E02
1.781,0.677 1.625,0.677 1.625,0.677 1.625,0.958 false 1.677,1.385 1.594,1.385 1.594,1.385 1.594,3.26 false 1.677,1.698 1.594,1.698 false 1.677,2.052 1.594,2.052 false 0.698,2.771 1.021,2.771 false 4.958,4.76 4.813,4.76 4.813,4.76 4.813,4.469 false 4.573,4.76 4.719,4.76 4.719,4.76 4.719,4.469 false 3.167,7.583 3.458,7.75 0.292,0.167 10 false MB 4.865,6.375 5.156,6.542 0.292,0.167 10 false 2A 1.875,6.375 2.167,6.542 0.292,0.167 10 false 2B 1.167,5.104 1.458,5.271 0.292,0.167 10 false 2D 0.521,1.5 0.813,1.667 0.292,0.167 10 false 2D 3.938,5.135 4.229,5.302 0.292,0.167 10 false 2C 0.521,2.156 0.813,2.323 0.292,0.167 10 false 2C 4.875,3.792 5.167,3.958 0.292,0.167 10 false L7 6.26,5.094 6.552,5.26 0.292,0.167 10 false 2F 5.594,5.104 5.885,5.271 0.292,0.167 10 false 2E 5.875,5.094 6.208,5.385 0.333,0.292 10 false *A 6.552,5.094 6.917,5.417 0.365,0.323 10 false *B 2.427,3.802 2.719,3.969 0.292,0.167 10 false L8 0.26,2.552 0.552,2.719 0.292,0.167 10 false 2E 0.573,2.542 0.885,2.76 0.313,0.219 10 false *A 0.573,2.854 0.948,3.156 0.375,0.302 10 false *B 0.271,2.854 0.563,3.021 0.292,0.167 10 false 2F 2.01,1.698 2.302,1.865 0.292,0.167 10 false L7 2.01,2.063 2.302,2.229 0.292,0.167 10 false L8 6.281,1.521 6.49,1.688 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.271,2.177 6.479,2.344 0.208,0.167 10 false 2A 1.823,0.604 1.979,0.76 0.156,0.156 10 false *1 0.375,0.198 0.802,0.625 0.427,0.427 10 false *a 1.5,3.292 1.656,3.448 0.156,0.156 10 false *2 5.01,4.688 5.583,4.844 0.573,0.156 10 false CANL 4.167,4.688 4.74,4.844 0.573,0.156 10 false CANH

Text in Illustration
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L7 main body ECU (multiplex network body ECU) connector.

U154949E02
2.448,0.323 2.333,0.323 2.333,0.323 1.833,1.333 false 2.635,0.594 2.469,0.594 2.469,0.594 1.917,1.333 false 6.729,1.771 6.583,1.771 6.583,1.771 6.26,1.594 false 5.927,0.51 5.677,0.51 5.677,0.51 5.521,1.135 false 0.115,0.073 0.385,0.375 0.271,0.302 10 false *a 3.865,0.115 4.333,0.406 0.469,0.292 10 false *1 6.781,1.677 7.073,1.854 0.292,0.177 10 false BAT 4.125,1.313 4.448,1.531 0.323,0.219 10 false L61 1.615,0.49 1.958,0.76 0.344,0.271 10 false L7 2.521,0.24 2.906,0.417 0.385,0.177 10 false CANL 2.677,0.521 3.083,0.698 0.406,0.177 10 false CANH 5.958,0.458 6.365,0.635 0.406,0.177 10 false CG

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L7-14 (CANH) - L7-13 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L7-14 (CANH) - L61-4 (CG) SB - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L7-13 (CANL) - L61-4 (CG) W - G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L7-14 (CANH) - L61-16 (BAT) SB - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L7-13 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154707E04
1.063,2.885 1.375,2.5 false 1.323,3.073 1.625,2.469 false 1.896,2.469 1.948,3.073 false 2.396,2.469 2.708,2.875 false 1.615,1.104 1.969,1.313 0.354,0.208 10 false L51 0.198,0.156 0.531,0.427 0.333,0.271 10 false *a 0.771,2.906 1.063,3.083 0.292,0.177 10 false ESS 1.073,3.083 1.458,3.26 0.385,0.177 10 false CANL 1.74,3.094 2.146,3.271 0.406,0.177 10 false CANH 2.635,2.885 2.927,3.063 0.292,0.177 10 false BAT

Disconnect the L51 spiral cable with sensor sub-assembly (steering angle sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L51-4 (CANH) - L51-3 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L51-4 (CANH) - L51-2 (ESS) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-3 (CANL) - L51-2 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-4 (CANH) - L51-6 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L51-3 (CANL) - L51-6 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




YAW RATE SENSOR


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154692E01
0.062,2.631 0.479,2.796 0.417,0.165 10 *1 2.949,1.507 3.286,1.670 0.336,0.163 10 L12 0.292,2.062 0.626,2.225 0.335,0.163 10 GND 0.88,2.302 1.284,2.465 0.404,0.163 10 CANL 1.555,2.302 1.987,2.465 0.432,0.163 10 CANH 0.18,3.96 0.478,4.138 0.298,0.179 10 L61 1.084,1.694 0.728,2.124 false 1.295,1.716 1.093,2.214 false 1.578,1.72 1.789,2.268 false 1.904,4.293 2.193,4.455 0.289,0.163 10 BAT 2.495,4.037 2.27,4.387 false 0.093,0.062 2.427,0.558 2.334,0.496 10 *a

Disconnect the L12 yaw rate sensor connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Yaw Rate Sensor)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L12-3 (CANH) - L12-2 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L12-3 (CANH) - L12-1 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L12-2 (CANL) - L12-1 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L12-3 (CANH) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L12-2 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


U154954E01
1.821,1.965 2.077,2.121 0.256,0.156 10 z16 3.291,1.795 3.564,1.951 0.272,0.156 10 z15 3.765,1.801 4.038,1.957 0.272,0.156 10 z14 4.304,0.639 4.577,0.795 0.272,0.156 10 L54 5.019,0.639 5.291,0.795 0.272,0.156 10 A27 4.472,2.523 4.892,2.678 0.421,0.156 10 CANL 3.911,2.523 4.332,2.678 0.421,0.156 10 CANH 4.646,1.302 4.163,2.512 false 4.657,1.44 4.657,2.512 false 0.07,0.046 0.276,0.242 0.206,0.197 10 *a

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A27 and L54 power steering ECU assembly connectors.

U154726E01
0.166,0.148 2.563,0.497 2.397,0.349 10 *a 2.248,2.449 2.701,2.612 0.453,0.163 10 CANL 1.292,2.449 1.745,2.612 0.453,0.163 10 CANH 5.299,1.023 5.625,1.186 0.325,0.163 10 PIG 5.215,2.357 5.647,2.519 0.432,0.163 10 PGND 1.115,1.631 1.437,1.803 0.323,0.172 10 L54 1.966,1.891 1.513,2.414 false 1.979,2.065 2.403,2.414 false 4.93,1.588 5.382,1.183 false 4.93,1.912 5.382,2.316 false 3.909,1.643 4.232,1.815 0.323,0.172 10 A27

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L54-1 (CANH) - L54-7 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L54-1 (CANH) - A27-2 (PGND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-7 (CANL) - A27-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-1 (CANH) - A27-1 (PIG) R - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L54-7 (CANL) - A27-1 (PIG) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U154534E01
1.278,1.997 1.674,2.136 0.396,0.139 10 CANL 2.438,1.997 2.858,2.136 0.419,0.139 10 CANH 2.103,1.384 2.321,2.064 2.321,2.064 2.429,2.064 false 1.991,1.384 1.774,2.064 1.774,2.064 1.665,2.064 false 2.418,0.623 2.695,0.764 0.277,0.140 10 L62 4.574,0.623 4.851,0.764 0.277,0.140 10 L63 0.063,0.037 0.259,0.207 0.195,0.170 10 *a

Text in Illustration
*a Component without harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.

U154730E02
2.573,1.552 2.354,1.24 false 4.5,1.552 4.792,1.292 false 4.021,1.552 4.333,0.958 false 3.906,1.552 3.594,0.938 false 0.083,0 0.438,0.302 0.354,0.302 10 false *a 1.625,1.521 2.063,1.792 0.438,0.271 10 false L62 2.188,1.083 2.375,1.26 0.188,0.177 10 false +B 4.823,1.177 4.979,1.354 0.156,0.177 10 false E 3.208,0.771 3.615,0.948 0.406,0.177 10 false CANH 4.354,0.792 4.74,0.969 0.385,0.177 10 false CANL

Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L62-9 (CANH) - L62-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L62-9 (CANH) - L62-15 (E) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L62-10 (CANL) - L62-15 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L62-9 (CANH) - L62-1 (+B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L62-10 (CANL) - L62-1 (+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


U191404E02
4.771,1.25 4.5,1.25 4.5,1.25 4.5,0.823 false 4.104,1.25 4.375,1.25 4.375,1.25 4.375,0.813 false 1.833,0.167 2.24,0.323 0.406,0.156 10 false L168 2.24,0.177 2.646,0.333 0.406,0.156 10 false *A 3.021,0.167 3.427,0.323 0.406,0.156 10 false *B 2.615,0.177 3.021,0.333 0.406,0.156 10 false L169 1.479,1.625 1.885,1.781 0.406,0.156 10 false L167 2.26,1.625 2.667,1.781 0.406,0.156 10 false L166 3.854,1.563 4.26,1.719 0.406,0.156 10 false L175 5.385,1.417 5.792,1.573 0.406,0.156 10 false RA 4.542,0.177 4.948,0.333 0.406,0.156 10 false L35 0.135,0.104 0.542,0.26 0.406,0.156 10 false *a 4.813,1.146 5.729,1.385 0.917,0.24 12 false CANH 3.625,1.156 4.542,1.396 0.917,0.24 12 false CANL

Text in Illustration
*A w/ Rear View Monitor System *B w/ Intelligent Parking Assist System
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L35 and L167 radio and display receiver assembly connectors.

U191095E02
1.865,0.552 2.021,0.552 2.021,0.552 2.021,1.688 true 2.344,0.552 2.125,0.552 2.125,0.552 2.125,1.688 true 5.792,0.521 5.635,0.521 5.635,0.521 5.635,1.5 true 5.198,2.302 5.031,2.302 5.031,2.302 5.031,1.906 true 0.135,0.094 0.313,0.271 0.177,0.177 10 false *a 2.385,0.49 2.823,0.667 0.438,0.177 10 false CANL 1.448,0.479 1.885,0.656 0.438,0.177 10 false CANH 5.865,0.448 6.167,0.625 0.302,0.177 10 false +B1 5.229,2.229 5.677,2.417 0.448,0.188 10 false GND1 0.688,1.521 0.969,1.698 0.281,0.177 10 false L35 3.917,1.531 4.354,1.708 0.438,0.177 10 false L167

Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L35-9 (CANH) - L35-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L35-9 (CANH) - L167-7 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-10 (CANL) - L167-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-9 (CANH) - L167-4 (+B1) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L35-10 (CANL) - L167-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


U191405E02
4.49,0.823 4.49,1.271 4.49,1.271 4.677,1.271 false 4.375,0.813 4.375,1.271 4.375,1.271 4.198,1.271 false 4.698,1.188 5.229,1.406 0.531,0.219 10 false CANH 3.813,1.188 4.344,1.406 0.531,0.219 10 false CANL 0.104,0.115 0.281,0.313 0.177,0.198 10 false *a 1.833,0.177 2.24,0.333 0.406,0.156 10 false L172 2.229,0.167 2.635,0.323 0.406,0.156 10 false *A 3.021,0.167 3.427,0.323 0.406,0.156 10 false *B 2.625,0.167 3.031,0.323 0.406,0.156 10 false L173 1.479,1.615 1.885,1.771 0.406,0.156 10 false L171 2.26,1.615 2.667,1.771 0.406,0.156 10 false L170 3.865,1.563 4.271,1.719 0.406,0.156 10 false L176 5.375,1.417 5.781,1.573 0.406,0.156 10 false RA 4.563,0.177 4.969,0.333 0.406,0.156 10 false L38

Text in Illustration
*A w/o Intelligent Parking Assist System *B w/ Intelligent Parking Assist System
*a Component without harness connected
(Navigation Receiver Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L38 and L171 navigation receiver assembly connectors.

U191096E02
1.865,0.552 2.021,0.552 2.021,0.552 2.021,1.688 true 2.344,0.552 2.125,0.552 2.125,0.552 2.125,1.688 true 5.813,0.521 5.656,0.521 5.656,0.521 5.656,1.5 true 5.198,2.271 5.031,2.271 5.031,2.271 5.031,1.875 true 0.135,0.125 0.313,0.302 0.177,0.177 10 false *a 2.375,0.479 2.813,0.656 0.438,0.177 10 false CANL 1.448,0.479 1.885,0.656 0.438,0.177 10 false CANH 5.865,0.448 6.167,0.625 0.302,0.177 10 false +B1 5.229,2.198 5.677,2.385 0.448,0.188 10 false GND1 0.688,1.531 0.969,1.708 0.281,0.177 10 false L38 3.917,1.531 4.365,1.719 0.448,0.188 10 false L171

Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L38-9 (CANH) - L38-10 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L38-9 (CANH) - L171-7 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-10 (CANL) -L171-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-9 (CANH) - L171-4 (+B1) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L38-10 (CANL) - L171-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER SUB-ASSEMBLY


U191389E02
0.615,0.958 0.219,0.958 0.219,0.958 0.219,1.281 false 0.76,0.927 0.76,0.448 0.76,0.448 0.906,0.448 false 1.573,0.313 1.896,0.479 0.323,0.167 10 false L27 4.063,0.354 4.427,0.521 0.365,0.167 10 false L125 6.021,0.354 6.385,0.521 0.365,0.167 10 false L141 0.094,0.052 0.583,0.406 0.49,0.354 10 false *a 0.948,0.375 1.438,0.729 0.49,0.354 10 false CANH 0.052,1.292 0.5,1.5 0.448,0.208 10 false CANL

Text in Illustration
*a Component without harness connected
(Combination Meter Sub-assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L27 combination meter sub-assembly connector.

U154724E02
3.625,2 3.875,2.365 false 4.76,0.969 4.615,0.969 4.615,0.969 4.385,1.948 false 4.75,1.344 4.667,1.344 4.667,1.344 4.479,1.948 false 2.292,1.229 2.375,1.229 2.375,1.229 2.677,1.958 false 0.219,0.177 2.615,0.531 2.396,0.354 10 false *a 4.792,1.25 5.24,1.417 0.448,0.167 10 false CANL 4.792,0.885 5.24,1.052 0.448,0.167 10 false CANH 2.167,1.135 2.344,1.302 0.177,0.167 10 false B 3.844,2.406 4.094,2.573 0.25,0.167 10 false ES 1.813,1.75 2.135,1.927 0.323,0.177 10 false L27

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) SB - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L27-19 (CANH) - L27-11 (ES) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-20 (CANL) - L27-11 (ES) G - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-19 (CANH) - L27-1 (B) SB - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L27-20 (CANL) - L27-1 (B) G - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


U154711E03
3.677,0.979 3.719,0.979 3.719,0.979 3.885,1.698 false 4.229,0.958 4.188,0.958 4.188,0.958 4.021,1.688 false 3.969,2.188 4.292,2.365 0.323,0.177 10 false L17 5.646,2.188 5.969,2.365 0.323,0.177 10 false z11 4.271,0.885 4.729,1.177 0.458,0.292 10 false CANH 3.281,0.906 3.74,1.198 0.458,0.292 10 false CANL 0.083,0.031 0.302,0.229 0.219,0.198 10 false *a

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L17 air conditioning amplifier assembly connector.

U154725E01
0.22,0.181 2.617,0.530 2.397,0.349 10 *a 4.352,0.909 4.805,1.072 0.453,0.163 10 CANL 2.626,0.909 3.079,1.072 0.453,0.163 10 CANH 2.342,2.471 2.517,2.634 0.175,0.163 10 B 4.141,2.471 4.573,2.634 0.432,0.163 10 GND 1.825,1.788 2.148,1.960 0.323,0.172 10 L17 3.65,1.962 3.06,1.072 false 3.746,1.962 4.336,1.072 false 2.702,2.091 2.415,2.46 false 4.281,2.46 3.927,1.964 false

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L17-11 (CANH) - L17-14 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-12 (CANL) - L17-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-11 (CANH) - L17-21 (B) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L17-12 (CANL) - L17-21 (B) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


U191242E02
1.698,0.365 2.281,0.365 2.281,0.365 2.281,0.844 false 1.896,1.594 2.375,1.594 2.375,1.594 2.375,1.156 false 1.76,1.417 2.24,1.417 2.24,1.417 2.24,1.167 false 1.573,0.563 2.167,0.563 2.167,0.563 2.167,0.844 false 3.531,0.229 3.823,0.448 0.292,0.219 10 false L60 1.313,0.292 1.708,0.542 0.396,0.25 10 false CA2L 1.51,1.531 1.958,1.729 0.448,0.198 10 false CA2H 0.083,0.021 0.26,0.198 0.177,0.177 10 false *a 1.375,1.313 1.823,1.51 0.448,0.198 10 false CA1P 1.198,0.479 1.594,0.729 0.396,0.25 10 false CA1N

Text in Illustration
*a Component without harness connected
(Driving Support ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191155E02
2.833,1.865 2.698,2.688 false 2.865,1.729 2.719,0.927 false 2.729,1.875 2.146,2.698 false 2.75,1.688 2.167,0.938 false 1.771,1.875 1.521,2.708 false 1.313,1.885 0.927,2.698 false 0.469,0.906 0.813,1.083 0.344,0.177 10 false L60 2.469,0.75 2.854,0.927 0.385,0.177 10 false CA1N 0.115,0.104 0.271,0.281 0.156,0.177 10 false *a 2.458,2.688 2.844,2.865 0.385,0.177 10 false CA1P 1.917,0.75 2.302,0.927 0.385,0.177 10 false CA2L 1.906,2.698 2.292,2.875 0.385,0.177 10 false CA2H 1.469,2.729 1.646,2.906 0.177,0.177 10 false B 0.698,2.698 1.073,2.875 0.375,0.177 10 false GND

Disconnect the L60 driving support ECU assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Sub Bus 11 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L60-39 (CA2H) - L60-17 (CA2L) B - R HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L60-39 (CA2H) - L60-25 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-17 (CA2L) - L60-25 (GND) R - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-39 (CA2H) - L60-30 (B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L60-17 (CA2L) - L60-30 (B) R - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 13 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L60-40 (CA1P) - L60-18 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L60-40 (CA1P) - L60-25 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-18 (CA1N) - L60-25 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L60-40 (CA1P) - L60-30 (B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L60-18 (CA1N) - L60-30 (B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Intelligent Parking Assist System)


U191302E02
1.573,1.531 1.667,1.531 1.667,1.531 1.802,1.083 false 2.177,1.531 2.094,1.531 2.094,1.531 1.917,1.083 false 2.76,0.302 3.01,0.479 0.25,0.177 10 false L65 5.698,0.292 5.948,0.469 0.25,0.177 10 false L64 0.49,0.448 0.865,0.625 0.375,0.177 10 false L136 1.156,1.438 1.604,1.625 0.448,0.188 10 false CANH 2.208,1.458 2.656,1.646 0.448,0.188 10 false CANL 0.083,0 0.396,0.26 0.313,0.26 10 false *a

Text in Illustration
*a Component without harness connected
(Parking Assist ECU)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191128E01
0.071,0.06 0.283,0.260 0.212,0.200 10 *a 2.224,0.341 2.498,0.518 0.273,0.177 10 L65 1.576,2.716 1.849,2.893 0.273,0.177 10 L64 1.939,1.897 2.331,2.056 0.392,0.159 10 CANL 2.114,2.24 2.566,2.394 0.452,0.154 10 CANH 2.77,2.709 3.185,2.863 0.415,0.154 10 GND1 0.311,2.686 0.529,2.841 0.218,0.154 10 +B 2.394,1.969 2.462,1.969 2.462,1.969 2.604,1.483 false 2.615,2.315 2.683,2.315 2.683,2.315 2.727,1.482 false 2.746,2.799 2.674,2.799 2.674,2.799 2.483,3.355 false 0.559,2.78 0.638,2.78 0.638,2.78 0.916,3.355 false

Disconnect the L64 and L65 parking assist ECU connectors.

Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L65-40 (CANH) - L65-39 (CANL) B - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L65-40 (CANH) - L64-4 (GND1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L65-39 (CANL) - L64-4 (GND1) L - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L65-40 (CANH) - L64-1 (+B) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L65-39 (CANL) - L64-1 (+B) L - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


U191365E02
2.323,0.833 2.635,0.99 0.313,0.156 10 false A76 0.146,0.063 0.427,0.219 0.281,0.156 10 false *a

Text in Illustration
*a Component without harness connected
(Millimeter Wave Radar Sensor Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191168E02
1.677,1.323 2.406,0.708 false 1.531,1.333 0.698,0.708 false 1.385,1.385 0.771,1.396 false 2.469,4.052 2.896,4.25 false 0.115,0.063 0.5,0.438 0.385,0.375 10 false *a 0.281,0.583 0.771,0.865 0.49,0.281 10 false CA1N 2.479,0.573 2.969,0.854 0.49,0.281 10 false CA1P 0.313,1.313 0.802,1.594 0.49,0.281 10 false SGND 2.938,4.198 3.25,4.479 0.313,0.281 10 false BAT 1.51,0.448 1.802,0.625 0.292,0.177 10 false A76 1.552,2.604 1.896,2.813 0.344,0.208 10 false L61 0.094,2.344 0.479,2.719 0.385,0.375 10 false *1

Disconnect the A76 millimeter wave radar sensor assembly connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A76-3 (CA1P) - A76-2 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A76-3 (CA1P)- A76-1 (SGND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A76-2 (CA1N) - A76-1 (SGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A76-3 (CA1P) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A76-2 (CA1N) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)


U191166E01
4.676,0.739 4.994,0.917 0.318,0.177 10 U13 3.513,1.616 3.906,1.775 0.392,0.159 10 CA1N 3.516,1.097 3.968,1.251 0.452,0.154 10 CA1P 3.955,1.163 4.075,1.163 4.075,1.163 4.473,1.356 false 3.952,1.691 4.063,1.691 4.063,1.691 4.465,1.527 false 0.244,0.083 0.517,0.261 0.273,0.177 10 *a

Text in Illustration
*a Component without harness connected
(Lane Departure Warning Camera)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191169E01
1.512,2.596 1.785,2.773 0.273,0.177 10 L61 1.507,0.544 1.810,0.721 0.303,0.177 10 U13 2.65,1.25 3.042,1.408 0.392,0.159 10 CA1P 2.632,1.984 3.084,2.138 0.452,0.154 10 CA1N 2.577,1.335 2.461,1.335 2.461,1.335 2.094,1.451 false 1.511,2.256 1.768,2.256 1.768,2.256 1.925,1.811 false 0.298,2.493 0.572,2.670 0.273,0.177 10 *1 0.281,0.2 0.554,0.377 0.273,0.177 10 *a 1.026,2.166 1.478,2.320 0.452,0.154 10 GND 2.56,2.064 2.443,2.064 2.443,2.064 2.086,1.818 false 2.781,4.316 3.233,4.470 0.452,0.154 10 BAT 2.709,4.396 2.592,4.396 2.592,4.396 2.449,4.033 false

Disconnect the U13 lane departure warning camera connector.

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to Lane Departure Warning Camera)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
U13-6 (CA1P) - U13-12 (CA1N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
U13-6 (CA1P) - U13-11 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
U13-12 (CA1N) - U13-11 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
U13-6 (CA1P) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
U13-12 (CA1N) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher