Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) U

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  TERMINALS OF ECU  


NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Turn the power switch off before measuring the resistances between CAN main bus lines and between CAN branch lines.

·

Turn the power switch off before inspecting CAN bus lines for a ground short.

·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



CAN NO. 1 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 1 junction connector (engine room main wire side).

i.

Connection diagram

U154814E02
3.229,1.406 3.229,0.677 3.229,0.677 2.854,0.677 false 3.375,1.427 3.375,0.281 3.375,0.281 3.75,0.281 false 3.375,1.667 3.375,2.5 3.375,2.5 3.75,2.5 false 3.229,1.677 3.229,2.396 3.229,2.396 2.865,2.396 false 3.521,1.396 3.521,0.583 3.521,0.583 4.438,0.583 false 3.521,1.667 3.521,2.229 3.521,2.229 4.51,2.229 false 3.667,1.417 3.667,0.865 3.667,0.865 4.729,0.865 false 3.677,1.667 3.677,2.052 3.677,2.052 4.781,2.052 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.271,0.604 3.104,0.917 0.833,0.313 10 false CANH*b 2.313,2.313 3.146,2.625 0.833,0.313 10 false CANL*b 3.802,0.208 4.635,0.521 0.833,0.313 10 false CANH*c 3.781,2.427 4.615,2.74 0.833,0.313 10 false CANL*c 2.406,1.417 2.771,1.635 0.365,0.219 10 false A67 4.469,0.49 5.302,0.802 0.833,0.313 10 false CANH*d 4.531,2.146 5.365,2.458 0.833,0.313 10 false CANL*d 4.76,0.792 5.594,1.104 0.833,0.313 10 false CANH*e 4.813,1.969 5.646,2.281 0.833,0.313 10 false CANL*e

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*e to ECM
(for Sub Bus 15)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) P ECM
(for V bus)
A67-7 (CANL) V
A67-2 (CANH) LG Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A67-8 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 15)
A67-10 (CANL) W



b.

Check the CAN No. 1 junction connector (instrument panel wire side).

i.

Connection diagram

U154815E03
3.802,1.406 3.802,0.396 3.802,0.396 3.438,0.396 false 3.948,1.406 3.948,0.677 3.948,0.677 4.323,0.677 false 3.948,1.719 3.948,2.438 3.948,2.438 4.323,2.438 false 3.802,1.719 3.802,2.552 3.802,2.552 3.438,2.552 false 3.521,1.417 3.521,0.75 3.521,0.75 3.146,0.75 false 3.51,1.729 3.51,2.167 3.51,2.167 3.146,2.167 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.594,0.667 3.427,0.979 0.833,0.313 10 false CANH*b 2.604,2.094 3.438,2.406 0.833,0.313 10 false CANL*b 2.865,0.323 3.698,0.635 0.833,0.313 10 false CANH*c 2.875,2.479 3.469,2.698 0.594,0.219 10 false CANL*c 2.375,1.417 2.729,1.635 0.354,0.219 10 false L132 4.354,0.604 5.188,0.917 0.833,0.313 10 false CANH*d 4.354,2.354 5.188,2.667 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector
(for Sub Bus 15)
*c Main body ECU (Multiplex Network Body ECU)
(for V Bus)
*d to CAN No. 2 Junction Connector
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R CAN No. 5 junction connector
(for Sub bus 15)
L132-9 (CANL) Y
L132-5 (CANH) SB Main body ECU (Multiplex network body ECU)
(for V bus)
L132-11 (CANL) W
L132-6 (CANH) B CAN No. 2 junction connector
(for V bus)
L132-12 (CANL) W




CAN NO. 1 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 1 junction connector (engine room main wire side).

i.

Connection diagram

U191039E02
3.219,1.417 3.219,0.688 3.219,0.688 2.844,0.688 false 3.219,1.698 3.219,2.188 3.219,2.188 2.854,2.188 false 3.5,1.427 3.5,0.406 3.5,0.406 4.417,0.406 false 3.5,1.688 3.5,2.458 3.5,2.458 4.49,2.458 false 3.646,1.417 3.646,0.688 3.646,0.688 4.708,0.688 false 3.646,1.667 3.646,2.167 3.646,2.167 4.75,2.167 false 0.156,0.115 0.531,0.396 0.375,0.281 10 false *a 2.292,0.604 3.125,0.917 0.833,0.313 10 false CANH*b 2.323,2.104 3.156,2.417 0.833,0.313 10 false CANL*b 2.406,1.417 2.771,1.635 0.365,0.219 10 false A67 4.469,0.323 5.302,0.635 0.833,0.313 10 false CANH*c 4.542,2.375 5.375,2.688 0.833,0.313 10 false CANL*c 4.76,0.604 5.594,0.917 0.833,0.313 10 false CANH*d 4.802,2.083 5.635,2.396 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus)
*c to Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for Sub Bus 15)
*d to ECM
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A67-1 (CANH) LG Brake booster with master cylinder assembly (Skid control ECU)
(for V bus)
A67-7 (CANL) L
A67-3 (CANH) P Brake booster with master cylinder assembly (Skid control ECU)
(for Sub bus 15)
A67-9 (CANL) V
A67-4 (CANH) B ECM
(for Sub bus 15)
A67-10 (CANL) W



b.

Check the CAN No. 1 junction connector (instrument panel wire side).

i.

Connection diagram

U154815E03
3.802,1.406 3.802,0.396 3.802,0.396 3.438,0.396 false 3.948,1.406 3.948,0.677 3.948,0.677 4.323,0.677 false 3.948,1.719 3.948,2.438 3.948,2.438 4.323,2.438 false 3.802,1.719 3.802,2.552 3.802,2.552 3.438,2.552 false 3.521,1.417 3.521,0.75 3.521,0.75 3.146,0.75 false 3.51,1.729 3.51,2.167 3.51,2.167 3.146,2.167 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 2.594,0.667 3.427,0.979 0.833,0.313 10 false CANH*b 2.604,2.094 3.438,2.406 0.833,0.313 10 false CANL*b 2.865,0.323 3.698,0.635 0.833,0.313 10 false CANH*c 2.875,2.479 3.469,2.698 0.594,0.219 10 false CANL*c 2.375,1.417 2.729,1.635 0.354,0.219 10 false L132 4.354,0.604 5.188,0.917 0.833,0.313 10 false CANH*d 4.354,2.354 5.188,2.667 0.833,0.313 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 5 Junction Connector
(for Sub Bus 15)
*c to CAN No. 2 Junction Connector
(for V Bus)
*d Combination Meter Sub-assembly
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 1 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L132-3 (CANH) R CAN No. 5 junction connector
(for Sub bus 15)
L132-9 (CANL) Y
L132-5 (CANH) GR CAN No. 2 junction connector
(for V bus)
L132-11 (CANL) W
L132-6 (CANH) SB Combination meter sub-assembly
(for V bus)
L132-12 (CANL) G




CAN NO. 2 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 2 junction connector (instrument panel connector holder left side).

i.

Connection diagram

U154779E02
2.75,0.938 2.906,0.938 2.906,0.938 3.448,1.354 false 2.75,1.573 2.906,1.573 2.906,1.573 3.438,1.677 false 4.313,0.958 4.208,0.958 4.208,0.958 3.615,1.365 false 4.333,1.531 4.073,1.531 4.073,1.531 3.615,1.656 false 2.75,1.271 2.875,1.271 2.875,1.271 3.448,1.521 false 4.333,1.24 4.24,1.24 4.24,1.24 3.615,1.5 false 2.75,1.885 2.969,1.885 2.969,1.885 3.438,1.823 false 4.323,1.938 4.115,1.938 4.115,1.938 3.625,1.833 false 4.354,0.875 4.938,1.177 0.583,0.302 10 false CANH*b 4.354,1.469 4.938,1.771 0.583,0.302 10 false CANH*d 2.198,0.844 2.781,1.146 0.583,0.302 10 false CANL*b 4.354,1.167 4.938,1.469 0.583,0.302 10 false CANH*c 2.198,1.177 2.781,1.479 0.583,0.302 10 false CANL*c 2.198,1.49 2.781,1.792 0.583,0.302 10 false CANL*d 4.354,1.875 4.938,2.177 0.583,0.302 10 false CANH*e 2.198,1.823 2.781,2.125 0.583,0.302 10 false CANL*e 0.052,0 0.531,0.5 0.479,0.5 10 false *a 3.531,0.563 3.896,0.74 0.365,0.177 10 false L94

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
(for V Bus)
*c to CAN No. 1 Junction Connector
(for V Bus)
*d to Certification ECU (Smart Key ECU Assembly)
(for V Bus)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-2 (CANH) GR CAN No. 3 junction connector
(for V bus)
L94-1 (CANL) W
L94-5 (CANH) B CAN No. 1 junction connector
(for V bus)
L94-4 (CANL) W
L94-8 (CANH) B Certification ECU (Smart key ECU assembly)
(for V bus)
L94-7 (CANL) W
L94-11 (CANH) B Spiral cable with sensor sub-assembly (Steering angle sensor)
(for V bus)
L94-10 (CANL) W



b.

Check the CAN No. 2 junction connector (instrument panel connector holder right side).

i.

Connection diagram

U154780E03
2.531,0.875 2.792,0.875 2.792,0.875 3.563,1.344 false 2.531,1.49 3.052,1.49 3.052,1.49 3.552,1.667 false 4.229,0.927 3.99,0.927 3.99,0.927 3.698,1.333 false 4.25,1.531 3.854,1.531 3.854,1.531 3.729,1.646 false 2.531,1.198 2.958,1.198 2.958,1.198 3.563,1.5 false 4.25,1.229 4.01,1.229 4.01,1.229 3.729,1.49 false 2.542,2 2.906,2 2.906,2 3.563,1.844 false 4.24,1.927 3.885,1.927 3.885,1.927 3.719,1.844 false 2.531,2.344 3.104,2.344 3.104,2.344 3.583,1.99 false 4.24,2.25 3.844,2.25 3.844,2.25 3.698,1.99 false 4.281,0.844 4.865,1.146 0.583,0.302 10 false CANL*b 4.281,1.448 4.865,1.75 0.583,0.302 10 false CANL*d 1.938,0.781 2.521,1.083 0.583,0.302 10 false CANH*b 4.281,1.167 4.865,1.469 0.583,0.302 10 false CANL*c 1.938,1.115 2.521,1.417 0.583,0.302 10 false CANH*c 1.938,1.417 2.521,1.719 0.583,0.302 10 false CANH*d 4.281,1.854 4.865,2.156 0.583,0.302 10 false CANL*e 4.281,2.198 4.865,2.5 0.583,0.302 10 false CANL*f 1.969,1.917 2.552,2.219 0.583,0.302 10 false CANH*e 1.979,2.271 2.563,2.573 0.583,0.302 10 false CANH*f 0.052,0 0.417,0.375 0.365,0.375 10 false *a 3.49,0.563 3.906,0.802 0.417,0.24 10 false L95

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
(for V Bus)
*c to Air Conditioning Amplifier Assembly
(for V Bus)
*d to Airbag ECU Assembly
(for V Bus)
*e to Radio and Display Receiver Assembly
(for Radio and Display Type)
(for V Bus)
*f to DLC3
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-2 (CANH) R Power steering ECU assembly
(for V bus)
L95-3 (CANL) W
L95-5 (CANH) B Air conditioning amplifier assembly
(for V bus)
L95-6 (CANL) W
L95-8 (CANH) B Airbag ECU assembly
(for V bus)
L95-9 (CANL) W
L95-11 (CANH) L Radio and display receiver assembly*
(for V bus)
L95-12 (CANL) W
L95-14 (CANH) G DLC3
(for V bus)
L95-15 (CANL) W

*: for Radio and Display Type




CAN NO. 2 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 2 junction connector (instrument panel connector holder left side).

i.

Connection diagram

U191020E02
2.75,0.927 2.906,0.927 2.906,0.927 3.448,1.344 false 2.75,1.563 2.906,1.563 2.906,1.563 3.438,1.667 false 4.302,0.948 4.198,0.948 4.198,0.948 3.604,1.354 false 4.323,1.542 4.063,1.542 4.063,1.542 3.604,1.667 false 2.74,1.25 2.865,1.25 2.865,1.25 3.438,1.5 false 4.313,1.24 4.219,1.24 4.219,1.24 3.594,1.5 false 2.76,1.906 2.979,1.906 2.979,1.906 3.448,1.844 false 4.302,1.938 4.094,1.938 4.094,1.938 3.604,1.833 false 4.365,0.865 4.948,1.167 0.583,0.302 10 false CANL*b 4.354,1.458 4.938,1.76 0.583,0.302 10 false CANL*d 2.198,0.833 2.781,1.135 0.583,0.302 10 false CANH*b 4.365,1.156 4.948,1.458 0.583,0.302 10 false CANL*c 2.198,1.156 2.781,1.458 0.583,0.302 10 false CANH*c 2.198,1.479 2.781,1.781 0.583,0.302 10 false CANH*d 4.354,1.854 4.938,2.156 0.583,0.302 10 false CANL*e 2.208,1.813 2.792,2.115 0.583,0.302 10 false CANH*e 0.177,0.094 0.656,0.594 0.479,0.5 10 false *a 3.51,0.563 3.875,0.74 0.365,0.177 10 false L94

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
(for V Bus)
*c to CAN No. 3 Junction Connector
(for V Bus)
*d to Certification ECU (Smart Key ECU Assembly)
(for V Bus)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L94-1 (CANH) GR CAN No. 1 junction connector
(for V bus)
L94-2 (CANL) W
L94-4 (CANH) B CAN No. 3 junction connector
(for V bus)
L94-5 (CANL) W
L94-7 (CANH) B Certification ECU (Smart key ECU assembly)
(for V bus)
L94-8 (CANL) W
L94-10 (CANH) B Spiral cable with sensor sub-assembly (Steering angle sensor)
(for V bus)
L94-11 (CANL) W



b.

Check the CAN No. 2 junction connector (instrument panel connector holder right side).

i.

Connection diagram

U191021E02
2.531,0.865 2.792,0.865 2.792,0.865 3.563,1.333 false 2.531,1.469 3.052,1.469 3.052,1.469 3.552,1.646 false 4.229,0.927 3.99,0.927 3.99,0.927 3.698,1.333 false 4.25,1.531 3.854,1.531 3.854,1.531 3.729,1.646 false 2.531,1.198 2.958,1.198 2.958,1.198 3.563,1.5 false 4.25,1.24 4.01,1.24 4.01,1.24 3.729,1.5 false 2.542,2.01 2.906,2.01 2.906,2.01 3.563,1.854 false 4.24,1.958 3.885,1.958 3.885,1.958 3.719,1.875 false 2.531,2.365 3.104,2.365 3.104,2.365 3.583,2.01 false 4.24,2.271 3.844,2.271 3.844,2.271 3.698,2.01 false 4.281,0.833 4.865,1.135 0.583,0.302 10 false CANH*b 4.281,1.448 4.865,1.75 0.583,0.302 10 false CANH*d 1.99,0.76 2.573,1.063 0.583,0.302 10 false CANL*b 4.281,1.156 4.865,1.458 0.583,0.302 10 false CANH*c 2,1.083 2.583,1.385 0.583,0.302 10 false CANL*c 1.99,1.365 2.573,1.667 0.583,0.302 10 false CANL*d 4.281,1.875 4.865,2.177 0.583,0.302 10 false CANH*e 4.281,2.198 4.865,2.5 0.583,0.302 10 false CANH*f 2,1.906 2.583,2.208 0.583,0.302 10 false CANL*e 2.021,2.271 2.604,2.573 0.583,0.302 10 false CANL*f 0.156,0.125 0.521,0.5 0.365,0.375 10 false *a 3.49,0.563 3.906,0.802 0.417,0.24 10 false L95

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
(for V Bus)
*c to Air Conditioning Amplifier Assembly
(for V Bus)
*d to Airbag ECU Assembly
(for V Bus)
*e
·

to Navigation Receiver Assembly

(for Navigation Receiver Type)

·

to Radio and Display Receiver Assembly

(for Radio and Display Type)


(for V Bus)
*f to DLC3
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 2 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L95-3 (CANH) R Power steering ECU assembly
(for V bus)
L95-2 (CANL) W
L95-6 (CANH) B Air conditioning amplifier assembly
(for V bus)
L95-5 (CANL) W
L95-9 (CANH) B Airbag ECU assembly
(for V bus)
L95-8 (CANL) W
L95-12 (CANH) L
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


(for V bus)
L95-11 (CANL) W
L95-15 (CANH) G DLC3
(for V bus)
L95-14 (CANL) W

*1: for Navigation Receiver Type

*2: for Radio and Display Type




CAN NO. 3 JUNCTION CONNECTOR (for LHD)


a.

Check the CAN No. 3 junction connector (engine room main wire side).

i.

Connection diagram

U154816E02
3.229,1.417 3.229,0.688 3.229,0.688 2.854,0.688 false 3.229,1.698 3.229,2.417 3.229,2.417 2.865,2.417 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.271,0.615 3.104,0.927 0.833,0.313 10 false CANH*b 2.313,2.333 3.146,2.646 0.833,0.313 10 false CANL*b 2.406,1.396 2.771,1.615 0.365,0.219 10 false A68

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Transmission Control ECU Assembly
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) Y Transmission control ECU assembly
(for V bus)
A68-7 (CANL) BR



b.

Check the CAN No. 3 junction connector (instrument panel wire side).

i.

Connection diagram

U154817E03
3.667,1.427 3.667,0.698 3.667,0.698 3.292,0.698 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 3.813,1.698 3.813,2.417 3.813,2.417 4.177,2.417 false 3.667,1.688 3.667,2.406 3.667,2.406 3.292,2.406 false 4,1.448 4.281,1.333 4.281,1.333 4.427,1.333 false 4.01,1.656 4.292,1.771 4.292,1.771 4.448,1.771 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.708,0.615 3.542,0.927 0.833,0.313 10 false CANH*b 2.74,2.323 3.573,2.635 0.833,0.313 10 false CANL*b 4.24,0.604 5.073,0.917 0.833,0.313 10 false CANH*c 4.219,2.354 5.052,2.667 0.833,0.313 10 false CANL*c 2.385,1.417 2.802,1.635 0.417,0.219 10 false L133 4.458,1.24 5.167,1.458 0.708,0.219 10 false CANH*d 4.469,1.698 5.083,1.938 0.615,0.24 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Hybrid Vehicle Control ECU
(for V Bus)
*c to CAN No. 2 Junction Connector
(for V Bus)
*d to Combination Meter Sub-assembly
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Hybrid vehicle control ECU
(for V bus)
L133-10 (CANL) P
L133-5 (CANH) GR CAN No. 2 junction connector
(for V bus)
L133-11 (CANL) W
L133-6 (CANH) SB Combination meter sub-assembly
(for V bus)
L133-12 (CANL) G




CAN NO. 3 JUNCTION CONNECTOR (for RHD)


a.

Check the CAN No. 3 junction connector (engine room main wire side).

i.

Connection diagram

U191040E02
3.208,1.406 3.208,0.677 3.208,0.677 2.833,0.677 false 3.219,1.677 3.219,2.396 3.219,2.396 2.854,2.396 false 3.365,1.406 3.365,0.677 3.365,0.677 3.729,0.677 false 3.365,1.677 3.365,2.396 3.365,2.396 3.729,2.396 false 0.104,0.042 0.479,0.323 0.375,0.281 10 false *a 2.292,0.583 3.125,0.896 0.833,0.313 10 false CANH*b 2.313,2.302 3.146,2.615 0.833,0.313 10 false CANL*b 2.406,1.406 2.771,1.625 0.365,0.219 10 false A68 3.781,0.594 4.344,0.906 0.563,0.313 10 false CANH*c 3.781,2.313 4.344,2.625 0.563,0.313 10 false CANL*c

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b ECM
(for V Bus)
*c to Transmission Control ECU Assembly
(for V Bus)
- -


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
A68-1 (CANH) P ECM
(for V bus)
A68-7 (CANL) V
A68-2 (CANH) Y Transmission control ECU assembly
(for V bus)
A68-8 (CANL) BR



b.

Check the CAN No. 3 junction connector (instrument panel wire side).

i.

Connection diagram

U154817E03
3.667,1.427 3.667,0.698 3.667,0.698 3.292,0.698 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 3.813,1.698 3.813,2.417 3.813,2.417 4.177,2.417 false 3.667,1.688 3.667,2.406 3.667,2.406 3.292,2.406 false 4,1.448 4.281,1.333 4.281,1.333 4.427,1.333 false 4.01,1.656 4.292,1.771 4.292,1.771 4.448,1.771 false 0.083,0 0.458,0.281 0.375,0.281 10 false *a 2.708,0.615 3.542,0.927 0.833,0.313 10 false CANH*b 2.74,2.323 3.573,2.635 0.833,0.313 10 false CANL*b 4.24,0.604 5.073,0.917 0.833,0.313 10 false CANH*c 4.219,2.354 5.052,2.667 0.833,0.313 10 false CANL*c 2.385,1.417 2.802,1.635 0.417,0.219 10 false L133 4.458,1.24 5.167,1.458 0.708,0.219 10 false CANH*d 4.469,1.698 5.083,1.938 0.615,0.24 10 false CANL*d

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Hybrid Vehicle Control ECU
(for V Bus)
*c to Main body ECU (Multiplex Network Body ECU)
(for V Bus)
*d to CAN No. 2 Junction Connector
(for V Bus)


ii.

Check the connection diagram of the components which are connected to the CAN No. 3 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L133-4 (CANH) V Hybrid vehicle control ECU
(for V bus)
L133-10 (CANL) P
L133-5 (CANH) SB Main body ECU (Multiplex network body ECU)
(for V bus)
L133-11 (CANL) W
L133-6 (CANH) B CAN No. 2 junction connector
(for V bus)
L133-12 (CANL) W




CAN NO. 5 JUNCTION CONNECTOR


a.

Check the CAN No. 5 junction connector (instrument panel connector holder left side).

i.

Connection diagram

U191041E02
3.375,1.396 3.375,0.573 3.375,0.573 3,0.573 true 3.667,1.406 3.667,0.583 3.667,0.583 4.031,0.583 true 0.083,0.094 0.458,0.375 0.375,0.281 10 false *a 4.094,0.5 4.927,0.813 0.833,0.313 10 false CANL*b 2.385,1.396 2.75,1.615 0.365,0.219 10 false L101 2.417,0.49 3.25,0.802 0.833,0.313 10 false CANH*b

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 1 Junction Connector
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L101-2 (CANH) R CAN No. 1 junction connector
(for Sub bus 15)
L101-4 (CANL) Y



b.

Check the CAN No. 5 junction connector (instrument panel connector holder right side).

i.

Connection diagram

U154819E02
3.521,1.406 3.521,0.688 3.521,0.688 3.156,0.688 false 3.813,1.417 3.813,0.698 3.813,0.698 4.177,0.698 false 0.083,0.01 0.458,0.292 0.375,0.281 10 false *a 4.229,0.615 5.063,0.927 0.833,0.313 10 false CANH*b 2.594,0.594 3.427,0.906 0.833,0.313 10 false CANL*b 2.385,1.406 2.792,1.625 0.406,0.219 10 false L102

Text in Illustration
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Hybrid Vehicle Control ECU
(for Sub Bus 15)


ii.

Check the connection diagram of the components which are connected to the CAN No. 5 junction connector.

Terminal No. (Symbol) Wiring Color Connected to
L102-5 (CANH) B Hybrid vehicle control ECU
(for Sub bus 15)
L102-3 (CANL) W




DLC3


a.

Measure the resistance according to the value(s) in the table below.

U154710E01
0.269,0.211 0.787,0.374 0.518,0.163 10 *1 1.574,1.596 1.848,1.768 0.274,0.172 10 L61 4.207,1.94 4.493,2.319 false 3.362,2.342 3.815,2.504 0.453,0.163 10 CANL 4.251,0.719 4.704,0.881 0.453,0.163 10 CANH 4.262,0.869 3.834,1.391 false 3.071,0.869 3.499,1.391 false 4.389,2.342 4.740,2.504 0.351,0.163 10 BAT 2.842,0.719 3.192,0.881 0.351,0.163 10 CG 3.862,1.94 3.576,2.319 false

Text in Illustration
*1 DLC3 - -

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L61-6 (CANH) - L61-14 (CANL) G - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L61-6 (CANH) - L61-4 (CG) G - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-14 (CANL) - L61-4 (CG) W - G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L61-6 (CANH) - L61-16 (BAT) G - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L61-14 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HYBRID VEHICLE CONTROL ECU


C370358E01
1.333,1.458 1.75,1.708 0.417,0.25 2.667,1.458 3.083,1.708 0.417,0.25 4.167,1.458 4.583,1.708 0.417,0.25 5.417,1.458 5.833,1.708 0.417,0.25 5.26,1.167 5.74,0.292 5.74,0.292 5.917,0.292 true 5.25,1.021 5.656,0.125 5.656,0.125 5.844,0.125 true 5.146,1.188 4.646,0.281 4.646,0.281 4.469,0.281 true 5.146,1.042 4.667,0.083 4.667,0.083 4.49,0.083 true 0.49,0.094 0.802,0.292 0.313,0.198 10 false *a 1.417,1.49 1.729,1.688 0.313,0.198 10 false A21 2.75,1.49 3.063,1.688 0.313,0.198 10 false A22 4.292,1.5 4.604,1.698 0.313,0.198 10 false L5 5.542,1.49 5.854,1.688 0.313,0.198 10 false L6 4.083,0.01 4.594,0.208 0.51,0.198 10 false CA1H 4.073,0.208 4.583,0.406 0.51,0.198 10 false CA3P 5.958,0.219 6.469,0.417 0.51,0.198 10 false CA3N 5.885,0.042 6.396,0.24 0.51,0.198 10 false CA1L

Text in Illustration
*a Component without harness connected
(Hybrid Vehicle Control ECU)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191188E03
2.448,2.438 1.719,2 false 2.406,2.448 1.646,2.344 false 2.677,2.313 2.177,1.833 false 1.688,2.625 2.406,2.51 false 1.781,3.021 2.458,2.51 false 1.823,1.021 1.573,0.521 false 2.542,3.031 2.927,3.271 0.385,0.24 10 false L6 1.365,1.833 1.823,2.052 0.458,0.219 10 false CA1L 1.25,2.24 1.729,2.448 0.479,0.208 10 false CA1H 1.281,2.563 1.802,2.792 0.521,0.229 10 false CA3P 1.375,2.958 1.875,3.219 0.5,0.26 10 false CA3N 0.073,0 0.271,0.167 0.198,0.167 10 false *a 1.938,1.656 2.406,1.917 0.469,0.26 10 false BATT 1.417,0.333 1.729,0.594 0.313,0.26 10 false E1 1.969,0.375 2.354,0.635 0.385,0.26 10 false L5

Disconnect the L6 hybrid vehicle control ECU connector.

Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-25 (CA1H) - L6-24 (CA1L) V - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L6-25 (CA1H) - L5-6 (E1) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-24 (CA1L) - L5-6 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-25 (CA1H) - L6-3 (BATT) V - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-24 (CA1L) - L6-3 (BATT) P - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L6-31 (CA3P) - L6-30 (CA3N) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L6-31 (CA3P) - L5-6 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-30 (CA3N) - L5-6 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L6-31 (CA3P) - L6-3 (BATT) B - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L6-30 (CA3N) - L6-3 (BATT) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


U155205E03
5.5,0.219 5.802,0.948 false 6.25,0.219 5.958,0.948 false 5.135,0.5 5.771,1.135 false 6.615,0.5 5.969,1.135 false 5.25,0.042 5.646,0.198 0.396,0.156 10 false CANL 6.125,0.052 6.552,0.208 0.427,0.156 10 false CANN 4.875,0.323 5.302,0.479 0.427,0.156 10 false CANH 6.49,0.323 6.917,0.479 0.427,0.156 10 false CANP 2.302,2.479 2.604,2.635 0.302,0.156 10 false D28 5.542,2.479 5.844,2.635 0.302,0.156 10 false A57 0.094,0.021 0.469,0.365 0.375,0.344 10 false *a

Text in Illustration
*a Component without harness connected
(ECM)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A57 and D28 ECM connectors.

U154723E01
0.18,0.166 0.643,0.516 0.462,0.349 10 *a 3.109,1.531 3.405,1.704 0.296,0.172 10 D28 5.113,1.799 5.399,2.364 false 2.207,0.746 2.660,0.909 0.453,0.163 10 CANL 2.26,2.159 2.713,2.322 0.453,0.163 10 CANH 0.826,2.138 1.223,2.301 0.397,0.163 10 BATT 5.335,2.366 5.580,2.528 0.244,0.163 10 E1 0.517,1.514 0.848,1.686 0.331,0.172 10 A57 1.644,1.496 1.213,2.114 false 1.328,2.16 1.731,2.341 0.403,0.181 10 CANP 1.126,0.743 1.536,0.924 0.411,0.181 10 CANN 1.964,1.352 2.19,0.896 false 1.893,1.352 1.554,0.901 false 1.976,1.414 2.249,2.141 false 1.897,1.426 1.726,2.141 false

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-13 (CANH) - D28-104 (E1) P - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-5 (CANL) - D28-104 (E1) V - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-13 (CANH) - A57-20 (BATT) P - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-5 (CANL) - A57-20 (BATT) V - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A57-12 (CANP) - A57-4 (CANN) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A57-12 (CANP) - D28-104 (E1) B - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-4 (CANN) - D28-104 (E1) W - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A57-12 (CANP) - A57-20 (BATT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A57-4 (CANN) - A57-20 (BATT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TRANSMISSION CONTROL ECU ASSEMBLY


U154743E01
4.222,0.473 4.486,0.654 0.264,0.181 10 A24 2.637,0.473 2.901,0.654 0.264,0.181 10 A23 3.238,2.107 3.653,2.272 0.415,0.165 10 CA1H 4.143,2.093 4.532,2.250 0.389,0.157 10 CA1L 3.64,2.172 3.693,2.172 3.693,2.172 3.844,1.612 false 4.143,2.169 4.097,2.169 4.097,2.169 3.957,1.618 false 0.074,0.045 0.278,0.220 0.204,0.175 10 *a

Text in Illustration
*a Component without harness connected
(Transmission Control ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154768E02
2.073,1.688 1.802,2.156 false 2.167,1.698 2.438,2.177 false 2.104,3.719 2.521,4.146 false 1.208,1.354 0.906,0.99 false 0.052,0 0.406,0.375 0.354,0.375 10 false *a 0.5,1.448 0.927,1.792 0.427,0.344 10 false A24 0.51,3.51 0.927,3.844 0.417,0.333 10 false A23 2.479,2.198 2.885,2.375 0.406,0.177 10 false CA1H 1.406,2.198 1.792,2.375 0.385,0.177 10 false CA1L 2.552,4.156 2.927,4.333 0.375,0.177 10 false BATT 0.677,0.792 0.865,0.969 0.188,0.177 10 false E1

Disconnect the A23 and A24 transmission control ECU assembly connectors.

Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A24-16 (CA1H) - A24-15 (CA1L) Y - BR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A24-16 (CA1H) - A24-1 (E1) Y - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-15 (CA1L) - A24-1 (E1) BR - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A24-16 (CA1H) - A23-15 (BATT) Y - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A24-15 (CA1L) - A23-15 (BATT) BR - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SKID CONTROL ECU)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154754E02
2.656,1.729 2.948,1 false 1.115,2.688 1.656,2.135 false 1.615,2.677 1.76,2.135 false 1.958,2.125 2.042,2.667 false 2.063,2.125 2.448,2.667 false 2.646,2.042 2.948,2.802 false 0.198,0.156 0.469,0.406 0.271,0.25 10 false *a 0.271,0.885 0.563,1.042 0.292,0.156 10 false A58 2.938,0.823 3.167,0.979 0.229,0.156 10 false BS 2.927,2.813 3.25,2.99 0.323,0.177 10 false GND 0.771,2.708 1.135,2.885 0.365,0.177 10 false CA2L 1.302,2.698 1.688,2.875 0.385,0.177 10 false CA2H 1.802,2.708 2.188,2.885 0.385,0.177 10 false CA1H 2.333,2.698 2.698,2.875 0.365,0.177 10 false CA1L

Disconnect the A58 brake booster with master cylinder assembly (skid control ECU) connector.

Text in Illustration
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
V Bus Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-37 (CA1H) - A58-38 (CA1L) LG - L HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-37 (CA1H) - A58-28 (GND) LG - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-38 (CA1L) - A58-28 (GND) L - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-37 (CA1H) - A58-15 (BS) LG - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-38 (CA1L) - A58-15 (BS) L - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Sub Bus 15 Branch Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A58-35 (CA2H) - A58-34 (CA2L) P - V HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A58-35 (CA2H) - A58-28 (GND) P - W HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-34 (CA2L) - A58-28 (GND) V - W LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A58-35 (CA2H) - A58-15 (BS) P - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A58-34 (CA2L) - A58-15 (BS) V - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG ECU ASSEMBLY


U191450E01
2.594,0.495 2.867,0.651 0.272,0.156 10 L16 3.936,0.495 4.208,0.651 0.272,0.156 10 R1 4.819,0.495 5.091,0.651 0.272,0.156 10 S1 2.647,2.359 3.058,2.514 0.411,0.156 10 CANH 3.14,1.642 2.865,2.346 false 3.324,2.359 3.735,2.514 0.411,0.156 10 CANL 3.311,1.925 3.503,2.346 false 0.14,0.106 0.399,0.365 0.259,0.259 10 *a

Text in Illustration
*a Component without harness connected
(Airbag ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L16 airbag ECU assembly connector.

U191001E02
1.208,1.156 1.5,1.635 false 1.417,1.854 1.198,2.323 false 1.688,1.875 1.604,2.229 false 5.719,1.938 5.927,2.344 false 0.188,0.146 2.583,0.5 2.396,0.354 10 false *a 0.99,2.333 1.438,2.5 0.448,0.167 10 false CANL 1,1 1.448,1.167 0.448,0.167 10 false CANH 1.521,2.26 1.719,2.427 0.198,0.167 10 false E1 5.854,2.354 6.208,2.521 0.354,0.167 10 false BAT 0.625,1.594 1.073,1.885 0.448,0.292 10 false L16 3.396,0.156 3.896,0.323 0.5,0.167 10 false *1 3.396,1.635 3.823,1.906 0.427,0.271 10 false L61

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L16-13 (CANH) - L16-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L16-13 (CANH) - L16-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-22 (CANL) - L16-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L16-13 (CANH) - L61-16 (BAT) B - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L16-22 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U191262E03
1.75,0.573 1.604,0.573 1.604,0.573 1.604,0.854 true 1.552,1.438 1.458,1.438 1.458,1.438 1.458,3.198 false 0.646,2.656 1.021,2.656 true 1.885,4.917 1.74,4.917 1.74,4.917 1.74,4.625 true 1.521,4.917 1.667,4.917 1.667,4.917 1.667,4.625 true 3.406,7.885 3.667,8.042 0.26,0.156 10 false MB 5.042,6.625 5.302,6.781 0.26,0.156 10 false 2A 1.781,6.583 2.042,6.74 0.26,0.156 10 false 2B 5.063,5.24 5.323,5.396 0.26,0.156 10 false 2C 1.781,5.281 2.042,5.438 0.26,0.156 10 false 2D 4.688,3.969 4.948,4.125 0.26,0.156 10 false 2E 4.99,3.969 5.25,4.208 0.26,0.24 10 false *A 5.667,3.969 5.927,4.177 0.26,0.208 10 false *B 5.365,3.969 5.625,4.125 0.26,0.156 10 false 2F 1.708,3.938 2.135,4.094 0.427,0.156 10 false L201 0.219,2.448 0.479,2.604 0.26,0.156 10 false 2E 0.521,2.448 0.802,2.688 0.281,0.24 10 false *A 0.51,2.729 0.802,2.969 0.292,0.24 10 false *B 0.219,2.74 0.479,2.896 0.26,0.156 10 false 2F 0.417,1.292 0.677,1.448 0.26,0.156 10 false 2D 0.417,2.031 0.677,2.188 0.26,0.156 10 false 2C 1.844,1.438 2.313,1.656 0.469,0.219 10 false L201 1.802,0.51 1.958,0.667 0.156,0.156 10 false *1 3.708,0.552 3.969,0.708 0.26,0.156 10 false MB 6.344,2.083 6.604,2.24 0.26,0.156 10 false 2A 6.333,1.396 6.594,1.552 0.26,0.156 10 false 2B 0.365,0.104 0.625,0.302 0.26,0.198 10 false *a 1.396,3.208 1.552,3.365 0.156,0.156 10 false *2 1.938,4.844 2.51,5 0.573,0.156 10 false CANL 1.104,4.854 1.677,5.01 0.573,0.156 10 false CANH

Text in Illustration
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) *2 1 connector
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -

U190881E04
1.75,0.667 1.594,0.667 1.594,0.667 1.594,0.948 false 1.552,1.417 1.469,1.417 1.469,1.417 1.469,3.292 false 1.563,1.771 1.479,1.771 false 1.563,2.104 1.479,2.104 false 0.698,2.781 1.021,2.781 true 4.969,4.76 4.823,4.76 4.823,4.76 4.823,4.469 true 4.583,4.75 4.729,4.75 4.729,4.75 4.729,4.458 true 3.156,7.594 3.448,7.76 0.292,0.167 10 false MB 4.875,6.375 5.167,6.542 0.292,0.167 10 false 2A 1.885,6.375 2.177,6.542 0.292,0.167 10 false 2B 1.167,5.104 1.458,5.271 0.292,0.167 10 false 2D 0.521,1.51 0.813,1.677 0.292,0.167 10 false 2D 3.938,5.135 4.229,5.302 0.292,0.167 10 false 2C 0.51,2.156 0.802,2.323 0.292,0.167 10 false 2C 4.823,3.813 5.25,3.979 0.427,0.167 10 false L201 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.594,5.104 5.885,5.271 0.292,0.167 10 false 2E 5.896,5.094 6.229,5.385 0.333,0.292 10 false *A 6.552,5.115 6.917,5.438 0.365,0.323 10 false *B 2.375,3.802 2.938,3.969 0.563,0.167 10 false L190 0.271,2.563 0.563,2.729 0.292,0.167 10 false 2E 0.552,2.552 0.865,2.771 0.313,0.219 10 false *A 0.552,2.854 0.927,3.156 0.375,0.302 10 false *B 0.271,2.865 0.563,3.031 0.292,0.167 10 false 2F 1.927,1.708 2.438,2 0.51,0.292 10 false L201 1.927,2.073 2.375,2.354 0.448,0.281 10 false L190 6.281,1.531 6.49,1.698 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.281,2.188 6.49,2.354 0.208,0.167 10 false 2A 1.792,0.594 1.948,0.75 0.156,0.156 10 false *1 0.375,0.198 0.802,0.625 0.427,0.427 10 false *a 1.417,3.313 1.573,3.469 0.156,0.156 10 false *2 5.01,4.677 5.583,4.833 0.573,0.156 10 false CANL 4.167,4.688 4.74,4.844 0.573,0.156 10 false CANH

Text in Illustration
*A for LHD *B for RHD
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors
*a Component without harness connected
(Instrument Panel Junction Block Assembly and Main Body ECU (Multiplex Network Body ECU))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L201 main body ECU (multiplex network body ECU) connector.

U191125E02
2.427,0.365 2.313,0.365 2.313,0.365 1.833,1.313 true 2.656,0.646 2.49,0.646 2.49,0.646 1.927,1.313 true 6.729,1.792 6.583,1.792 6.583,1.792 6.26,1.615 true 5.927,0.521 5.677,0.521 5.677,0.521 5.521,1.094 true 0.115,0.073 0.385,0.375 0.271,0.302 10 false *a 3.865,0.115 4.333,0.406 0.469,0.292 10 false *1 6.781,1.708 7.073,1.885 0.292,0.177 10 false BAT 4.135,1.313 4.458,1.531 0.323,0.219 10 false L61 1.573,0.49 1.917,0.76 0.344,0.271 10 false L201 2.479,0.292 2.865,0.469 0.385,0.177 10 false CANL 2.698,0.573 3.104,0.75 0.406,0.177 10 false CANH 5.958,0.458 6.365,0.635 0.406,0.177 10 false CG

Text in Illustration
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L201-14 (CANH) - L201-13 (CANL) SB - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L201-14 (CANH) - L61-4 (CG) SB - G HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L201-13 (CANL) - L61-4 (CG) W - G LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L201-14 (CANH) - L61-16 (BAT) SB - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L201-13 (CANL) - L61-16 (BAT) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (STEERING ANGLE SENSOR)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154707E05
1.063,2.885 1.375,2.5 false 1.323,3.073 1.625,2.469 false 1.896,2.469 1.948,3.073 false 2.396,2.469 2.708,2.875 false 1.615,1.104 1.969,1.313 0.354,0.208 10 false L51 0.198,0.156 0.531,0.427 0.333,0.271 10 false *a 0.771,2.906 1.063,3.083 0.292,0.177 10 false ESS 1.104,3.083 1.49,3.26 0.385,0.177 10 false CANL 1.729,3.083 2.135,3.26 0.406,0.177 10 false CANH 2.667,2.896 2.958,3.073 0.292,0.177 10 false BAT

Disconnect the L51 spiral cable with sensor sub-assembly (steering angle sensor) connector.

Text in Illustration
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor))


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L51-4 (CANH) - L51-3 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L51-4 (CANH) - L51-2 (ESS) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-3 (CANL) - L51-2 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L51-4 (CANH) - L51-6 (BAT) B - R HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L51-3 (CANL) - L51-6 (BAT) W - R LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


U154954E01
1.821,1.965 2.077,2.121 0.256,0.156 10 z16 3.291,1.795 3.564,1.951 0.272,0.156 10 z15 3.765,1.801 4.038,1.957 0.272,0.156 10 z14 4.304,0.639 4.577,0.795 0.272,0.156 10 L54 5.019,0.639 5.291,0.795 0.272,0.156 10 A27 4.472,2.523 4.892,2.678 0.421,0.156 10 CANL 3.911,2.523 4.332,2.678 0.421,0.156 10 CANH 4.646,1.302 4.163,2.512 false 4.657,1.44 4.657,2.512 false 0.07,0.046 0.276,0.242 0.206,0.197 10 *a

Text in Illustration
*a Component without harness connected
(Power Steering ECU Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A27 and L54 power steering ECU assembly connectors.

U154726E01
0.166,0.148 2.563,0.497 2.397,0.349 10 *a 2.248,2.449 2.701,2.612 0.453,0.163 10 CANL 1.292,2.449 1.745,2.612 0.453,0.163 10 CANH 5.299,1.023 5.625,1.186 0.325,0.163 10 PIG 5.215,2.357 5.647,2.519 0.432,0.163 10 PGND 1.115,1.631 1.437,1.803 0.323,0.172 10 L54 1.966,1.891 1.513,2.414 false 1.979,2.065 2.403,2.414 false 4.93,1.588 5.382,1.183 false 4.93,1.912 5.382,2.316 false 3.909,1.643 4.232,1.815 0.323,0.172 10 A27

Text in Illustration
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L54-1 (CANH) - L54-7 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L54-1 (CANH) - A27-2 (PGND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-7 (CANL) - A27-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L54-1 (CANH) - A27-1 (PIG) R - W HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L54-7 (CANL) - A27-1 (PIG) W - W LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U190969E01
1.896,0.575 2.227,0.730 0.331,0.156 10 L195 3.334,0.588 3.679,0.744 0.345,0.156 10 L196 4.904,0.566 5.276,0.722 0.372,0.156 10 L197 0.276,0.27 0.480,0.426 0.204,0.156 10 *a 5.021,0.855 5.457,1.115 0.436,0.260 10 CANH 4.746,1.484 4.744,0.931 4.744,0.931 4.635,0.931 false 4.831,1.484 4.834,0.931 4.834,0.931 4.965,0.931 false 4.217,0.857 4.653,1.117 0.436,0.260 10 CANL

Text in Illustration
*a Component without harness connected
(Certification ECU (Smart Key ECU Assembly))
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L195 and L197 certification ECU (smart key ECU assembly) connectors.

U191171E04
2,0.865 2.26,0.865 2.26,0.865 2.26,1.542 false 2.594,0.854 2.354,0.854 2.354,0.854 2.354,1.531 false 5.094,0.865 5.313,0.865 5.313,0.865 5.313,1.385 false 4.01,1.698 4.375,1.698 false 0.156,0 0.354,0.198 0.198,0.198 10 false *a 4.865,0.792 5.198,1.042 0.333,0.25 10 false +B 3.865,1.625 4.031,1.802 0.167,0.177 10 false E 2.656,0.781 3.135,1.031 0.479,0.25 10 false CANL 1.573,0.781 2.031,1.01 0.458,0.229 10 false CANH 2.01,0.396 2.469,0.656 0.458,0.26 10 false L197 4.729,0.448 5.115,0.677 0.385,0.229 10 false L195

Text in Illustration
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L197-14 (CANH) - L197-15 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L197-14 (CANH) - L195-11 (E) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L197-15 (CANL) - L195-11 (E) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L197-14 (CANH) - L195-2 (+B) B - B HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L197-15 (CANL) - L195-2 (+B) W - B LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


U191406E02
4.771,1.26 4.5,1.26 4.5,1.26 4.5,0.833 true 4.094,1.271 4.365,1.271 4.365,1.271 4.365,0.833 true 2.208,0.177 2.615,0.333 0.406,0.156 10 false L168 1.479,1.615 1.885,1.771 0.406,0.156 10 false L167 2.26,1.615 2.667,1.771 0.406,0.156 10 false L166 3.865,1.563 4.271,1.719 0.406,0.156 10 false L175 5.385,1.406 5.792,1.563 0.406,0.156 10 false RA 4.542,0.177 4.948,0.333 0.406,0.156 10 false L35 0.135,0.063 0.542,0.219 0.406,0.156 10 false *a 4.813,1.188 5.729,1.427 0.917,0.24 10 false CANH 3.719,1.198 4.635,1.438 0.917,0.24 10 false CANL

Text in Illustration
*a Component without harness connected
(Radio and Display Receiver Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L35 and L167 radio and display receiver assembly connectors.

U191095E02
1.865,0.552 2.021,0.552 2.021,0.552 2.021,1.688 true 2.344,0.552 2.125,0.552 2.125,0.552 2.125,1.688 true 5.792,0.521 5.635,0.521 5.635,0.521 5.635,1.5 true 5.198,2.302 5.031,2.302 5.031,2.302 5.031,1.906 true 0.135,0.094 0.313,0.271 0.177,0.177 10 false *a 2.385,0.49 2.823,0.667 0.438,0.177 10 false CANL 1.448,0.479 1.885,0.656 0.438,0.177 10 false CANH 5.865,0.448 6.167,0.625 0.302,0.177 10 false +B1 5.229,2.229 5.677,2.417 0.448,0.188 10 false GND1 0.688,1.521 0.969,1.698 0.281,0.177 10 false L35 3.917,1.531 4.354,1.708 0.438,0.177 10 false L167

Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L35-9 (CANH) - L35-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L35-9 (CANH) - L167-7 (GND1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-10 (CANL) - L167-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L35-9 (CANH) - L167-4 (+B1) L - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L35-10 (CANL) - L167-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




NAVIGATION RECEIVER ASSEMBLY (for Navigation Receiver Type)


U191407E02
4.49,0.833 4.49,1.281 4.49,1.281 4.677,1.281 true 4.375,0.823 4.375,1.281 4.375,1.281 4.198,1.281 true 4.708,1.198 5.24,1.417 0.531,0.219 10 false CANH 3.802,1.198 4.333,1.417 0.531,0.219 10 false CANL 0.063,0.073 0.24,0.271 0.177,0.198 10 false *a 2.188,0.177 2.594,0.333 0.406,0.156 10 false L172 1.469,1.625 1.875,1.781 0.406,0.156 10 false L171 2.25,1.615 2.656,1.771 0.406,0.156 10 false L170 3.854,1.573 4.26,1.729 0.406,0.156 10 false L176 5.385,1.417 5.792,1.573 0.406,0.156 10 false RA 4.552,0.177 4.958,0.333 0.406,0.156 10 false L38

Text in Illustration
*a Component without harness connected
(Navigation Receiver Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L38 and L171 navigation receiver assembly connectors.

U191096E02
1.865,0.552 2.021,0.552 2.021,0.552 2.021,1.688 true 2.344,0.552 2.125,0.552 2.125,0.552 2.125,1.688 true 5.813,0.521 5.656,0.521 5.656,0.521 5.656,1.5 true 5.198,2.271 5.031,2.271 5.031,2.271 5.031,1.875 true 0.135,0.125 0.313,0.302 0.177,0.177 10 false *a 2.375,0.479 2.813,0.656 0.438,0.177 10 false CANL 1.448,0.479 1.885,0.656 0.438,0.177 10 false CANH 5.865,0.448 6.167,0.625 0.302,0.177 10 false +B1 5.229,2.198 5.677,2.385 0.448,0.188 10 false GND1 0.688,1.531 0.969,1.708 0.281,0.177 10 false L38 3.917,1.531 4.365,1.719 0.448,0.188 10 false L171

Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L38-9 (CANH) - L38-10 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L38-9 (CANH) - L171-7 (GND1) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-10 (CANL) -L171-7 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L38-9 (CANH) - L171-4 (+B1) L - SB HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L38-10 (CANL) - L171-4 (+B1) W - SB LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER SUB-ASSEMBLY


U191389E02
0.615,0.958 0.219,0.958 0.219,0.958 0.219,1.281 false 0.76,0.927 0.76,0.448 0.76,0.448 0.906,0.448 false 1.573,0.313 1.896,0.479 0.323,0.167 10 false L27 4.063,0.354 4.427,0.521 0.365,0.167 10 false L125 6.021,0.354 6.385,0.521 0.365,0.167 10 false L141 0.094,0.052 0.583,0.406 0.49,0.354 10 false *a 0.948,0.375 1.438,0.729 0.49,0.354 10 false CANH 0.052,1.292 0.5,1.5 0.448,0.208 10 false CANL

Text in Illustration
*a Component without harness connected
(Combination Meter Sub-assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L27 combination meter sub-assembly connector.

U154724E02
3.625,2 3.875,2.365 false 4.76,0.969 4.615,0.969 4.615,0.969 4.385,1.948 false 4.75,1.344 4.667,1.344 4.667,1.344 4.479,1.948 false 2.292,1.229 2.375,1.229 2.375,1.229 2.677,1.958 false 0.219,0.177 2.615,0.531 2.396,0.354 10 false *a 4.792,1.25 5.24,1.417 0.448,0.167 10 false CANL 4.792,0.885 5.24,1.052 0.448,0.167 10 false CANH 2.167,1.135 2.344,1.302 0.177,0.167 10 false B 3.844,2.406 4.094,2.573 0.25,0.167 10 false ES 1.813,1.75 2.135,1.927 0.323,0.177 10 false L27

Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Sub-assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L27-19 (CANH) - L27-20 (CANL) SB - G HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
L27-19 (CANH) - L27-11 (ES) SB - BR HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-20 (CANL) - L27-11 (ES) G - BR LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L27-19 (CANH) - L27-1 (B) SB - L HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L27-20 (CANL) - L27-1 (B) G - L LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY


U154711E03
3.677,0.979 3.719,0.979 3.719,0.979 3.885,1.698 false 4.229,0.958 4.188,0.958 4.188,0.958 4.021,1.688 false 3.969,2.188 4.292,2.365 0.323,0.177 10 false L17 5.646,2.188 5.969,2.365 0.323,0.177 10 false z11 4.271,0.885 4.729,1.177 0.458,0.292 10 false CANH 3.281,0.906 3.74,1.198 0.458,0.292 10 false CANL 0.083,0.031 0.302,0.229 0.219,0.198 10 false *a

Text in Illustration
*a Component without harness connected
(Air Conditioning Amplifier Assembly)
- -

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the L17 air conditioning amplifier assembly connector.

U154725E01
0.22,0.181 2.617,0.530 2.397,0.349 10 *a 4.352,0.909 4.805,1.072 0.453,0.163 10 CANL 2.626,0.909 3.079,1.072 0.453,0.163 10 CANH 2.342,2.471 2.517,2.634 0.175,0.163 10 B 4.141,2.471 4.573,2.634 0.432,0.163 10 GND 1.825,1.788 2.148,1.960 0.323,0.172 10 L17 3.65,1.962 3.06,1.072 false 3.746,1.962 4.336,1.072 false 2.702,2.091 2.415,2.46 false 4.281,2.46 3.927,1.964 false

Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
- -


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
L17-11 (CANH) - L17-14 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-12 (CANL) - L17-14 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
L17-11 (CANH) - L17-21 (B) B - Y HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L17-12 (CANL) - L17-21 (B) W - Y LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher