OVERALL CAN BUS DIAGRAM (for LHD)
Control system CAN is composed of 3 buses.
| *1 | V Bus | *2 | Sub Bus 11 |
| *3 | Sub Bus 12 | *4 | V Bus Terminating Resistor |
| *5 | Sub Bus 11 Terminating Resistor | *6 | Sub Bus 12 Terminating Resistor |
| *7 | ECM
(for V Bus and Sub Bus 12) |
*8 | Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
| *9 | DLC3
(for V Bus) |
*10 | Airbag ECU Assembly
(for V Bus) |
| *11 | Power Management Control ECU
(Gateway Function Equipped ECU) |
*12 | Certification ECU (Smart Key ECU Assembly)
(for V Bus) |
| *13 | Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for V Bus) |
*14 | ·
Navigation ECU Sub-assembly ·
Radio and Display Receiver Assembly (for V Bus) |
| *15 | Power Steering ECU Assembly
(for V Bus) |
*16 | Yaw Rate Sensor
(for V Bus) |
| *17 | Transmission Control ECU Assembly
(for V Bus) |
*18 | Meter Circuit Plate
(for V Bus) |
| *19 | Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus and Sub Bus 12) |
*20 | Air Conditioning Amplifier Assembly
(for Sub Bus 12) |
| *21 | Seat Belt Control ECU
(for Sub Bus 11) |
*22 | Parking Assist ECU
(for Sub Bus 11) |
| *23 | Driving Support ECU Assembly
(for Sub Bus 11) |
*24 | CAN No. 4 Junction Connector
(for Sub Bus 11) |
The power management control ECU functions as a gateway between the V bus and sub bus 11, and the V bus and sub bus 12.
Refer to the following bus wiring diagrams for details.
V BUS (for LHD)
The CAN communication system connects to other networks via ECUs that function as a gateway (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM).
OVERALL CAN BUS DIAGRAM (for RHD)
Control system CAN is composed of 3 buses.
| *1 | V Bus | *2 | Sub Bus 11 |
| *3 | Sub Bus 12 | *4 | V Bus Terminating Resistor |
| *5 | Sub Bus 11 Terminating Resistor | *6 | Sub Bus 12 Terminating Resistor |
| *7 | ECM
(for V Bus and Sub Bus 12) |
*8 | Main Body ECU (Multiplex Network Body ECU)
(for V Bus) |
| *9 | DLC3
(for V Bus) |
*10 | Airbag ECU Assembly
(for V Bus) |
| *11 | Power Management Control ECU
(Gateway Function Equipped ECU) |
*12 | Certification ECU (Smart Key ECU Assembly)
(for V Bus) |
| *13 | Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)
(for V Bus) |
*14 | ·
Navigation ECU Sub-assembly ·
Radio and Display Receiver Assembly (for V Bus) |
| *15 | Power Steering ECU Assembly
(for V Bus) |
*16 | Yaw Rate Sensor
(for V Bus) |
| *17 | Transmission Control ECU Assembly
(for V Bus) |
*18 | Meter Circuit Plate
(for V Bus) |
| *19 | Brake Booster with Master Cylinder Assembly (Skid Control ECU)
(for V Bus and Sub Bus 12) |
*20 | Air Conditioning Amplifier Assembly
(for Sub Bus 12) |
| *21 | Seat Belt Control ECU
(for Sub Bus 11) |
*22 | Parking Assist ECU
(for Sub Bus 11) |
| *23 | Driving Support ECU Assembly
(for Sub Bus 11) |
*24 | CAN No. 4 Junction Connector
(for Sub Bus 11) |
The power management control ECU functions as a gateway between the V bus and sub bus 11, and the V bus and sub bus 12.
Refer to the following bus wiring diagrams for details.
V BUS (for RHD)
The CAN communication system connects to other networks via ECUs that function as a gateway (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>SYSTEM DIAGRAM).
SUB BUS 11
SUB BUS 12