Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2014.11–2016.05
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here))


·

Power source circuit of ECM

·

ECM main line or connector

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C240414E09
5.063,5.017 6.665,5.428 1.602,0.411 10 Trouble Area 2.395,2.296 2.943,2.518 0.548,0.222 10 DLC3 1.261,0.606 3.764,0.938 2.503,0.332 10 : CAN Main Bus Line (CANH) 1.261,0.949 3.764,1.281 2.503,0.332 10 : CAN Main Bus Line (CANL) 4.343,0.606 5.131,0.938 0.788,0.332 10 *1: for LHD 4.343,0.949 5.131,1.281 0.788,0.332 10 *2: for RHD 1.261,1.285 2.990,1.617 1.729,0.332 10 : CAN Branch Line (CANH) 1.261,1.628 2.990,1.960 1.729,0.332 10 : CAN Branch Line (CANL) 4.623,4.593 5.125,4.919 0.502,0.326 10 ECM 2.28,5.1 4.338,5.251 2.059,0.151 10 CAN No. 3 Junction Connector*1 2.28,5.451 4.338,5.601 2.059,0.151 10 CAN No. 1 Junction Connector*2 0.23,4.596 1.472,5.003 1.241,0.408 10 Combination Meter Sub-assembly 5.139,3.151 5.329,3.332 0.191,0.181 10 +B 5.065,3.546 5.333,3.728 0.268,0.181 10 +B2 4.946,3.986 5.333,4.167 0.387,0.181 10 IGSW 5.171,4.378 5.358,4.560 0.187,0.181 10 E1 4.38,3.735 4.768,3.916 0.387,0.181 10 CANL 4.371,3.114 4.782,3.295 0.411,0.181 10 CANH 0.885,4.027 1.276,4.209 0.391,0.181 10 120 Ω 4.445,4.116 4.836,4.298 0.391,0.181 10 120 Ω 5.41,3.131 5.674,3.312 0.264,0.181 10 A57 5.41,3.526 5.674,3.707 0.264,0.181 10 A57 5.41,3.974 5.674,4.155 0.264,0.181 10 A57 5.398,4.374 5.670,4.555 0.272,0.181 10 D28 4.051,3.839 4.315,4.020 0.264,0.181 10 A57 4.051,3.213 4.315,3.394 0.264,0.181 10 A57 5.49,2.95 5.646,3.132 0.156,0.181 10 2 5.489,3.344 5.645,3.525 0.156,0.181 10 1 5.458,3.766 5.629,3.947 0.171,0.181 10 28 5.408,4.192 5.657,4.373 0.249,0.181 10 104 4.089,3.03 4.261,3.211 0.171,0.181 10 13 4.139,3.673 4.294,3.854 0.156,0.181 10 5 6.158,3.974 6.545,4.315 0.387,0.341 10 IGN Fuse 5.409,2.634 6.686,2.886 1.277,0.252 10 to EFI MAIN Relay 0.362,2.36 1.642,2.729 1.280,0.369 10 CAN No. 2 Junction Connector 2.426,3.048 1.815,2.433 1.815,2.433 1.648,2.433 false 3.968,1.659 6.033,2.029 2.065,0.369 10 CAN No. 1 Junction Connector*1 3.385,3.048 3.761,1.733 3.761,1.733 3.928,1.733 false 3.968,2.01 6.033,2.379 2.065,0.369 10 CAN No. 3 Junction Connector*2 1.959,4.558 2.036,5.172 2.036,5.172 2.243,5.172 false 0.121,0.094 0.656,0.304 0.535,0.210 12 V Bus:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), and wait at least 20 seconds.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154226E02
1.781,1.667 1.365,2.573 false 1.406,1.021 1.781,1.583 false 0.146,0.104 0.917,0.427 0.771,0.323 10 false *a 0.25,1.781 0.531,1.948 0.281,0.167 10 false A57 1.01,0.927 1.542,1.073 0.531,0.146 10 false CANL 1.094,2.615 1.552,2.76 0.458,0.146 10 false CANH

Disconnect the A57 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-13 (CANH) - A57-5 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

2.CHECK ECM POWER SOURCE CIRCUIT

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)