There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.
| Symptom | Trouble Area |
|---|---|
| No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3. | ·
Short to ground in CAN main bus line ·
Short to ground in CAN branch line ·
Power management control ECU ·
ECM ·
Main body ECU (Multiplex network body ECU) ·
Meter circuit plate ·
Brake booster with master cylinder assembly (Skid control ECU) ·
Spiral cable with sensor sub-assembly (Steering angle sensor) ·
Yaw rate sensor ·
Power steering ECU assembly ·
Airbag ECU assembly ·
Transmission control ECU assembly ·
Certification ECU (Smart key ECU assembly) ·
Navigation ECU sub-assembly*1 ·
Radio and display receiver assembly*2 ·
CAN No. 1 junction connector ·
CAN No. 2 junction connector ·
CAN No. 3 junction connector |
*1: for Navigation receiver type
*2: for Radio and display type
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder left side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L94-2 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | CAN No. 3 junction connector |
| L94-1 (CANL) - L61-4 (CG) | |||
| L94-5 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | CAN No. 1 junction connector |
| L94-4 (CANL) - L61-4 (CG) | |||
| L94-8 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Certification ECU (Smart key ECU assembly) |
| L94-7 (CANL) - L61-4 (CG) | |||
| L94-11 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Spiral cable with sensor sub-assembly (Steering angle sensor) |
| L94-10 (CANL) - L61-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to CAN No. 3 Junction Connector |
| *c | to CAN No. 1 Junction Connector |
| *d | to Certification ECU (Smart Key ECU Assembly) |
| *e | to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN No. 1 junction connector main line) | B |
| NG (CAN No. 3 junction connector main line) | C |
| NG (ECU or sensor branch line) | D |
A
B
C
D
Disconnect the wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder right side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L95-2 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Power steering ECU assembly |
| L95-3 (CANL) - L61-4 (CG) | |||
| L95-5 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Yaw rate sensor |
| L95-6 (CANL) - L61-4 (CG) | |||
| L95-8 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Airbag ECU assembly |
| L95-9 (CANL) - L61-4 (CG) | |||
| L95-11 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | ·
Navigation ECU sub-assembly*1 ·
Radio and display receiver assembly*2 |
| L95-12 (CANL) - L61-4 (CG) | |||
| L95-14 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | DLC3 |
| L95-15 (CANL) - L61-4 (CG) |
*1: for Navigation receiver type
*2: for Radio and display type
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 2 Junction Connector) |
| *b | to Power Steering ECU Assembly |
| *c | to Yaw Rate Sensor |
| *d | to Airbag ECU Assembly |
| *e | ·
to Navigation ECU Sub-assembly*1 ·
to Radio and Display Receiver Assembly*2 |
| *f | to DLC3 |
*1: for Navigation receiver type
*2: for Radio and display type
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECU or sensor branch line) | B |
| NG (DLC3 branch line) | C |
A
B
C
Disconnect the wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L132-5 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Main body ECU (Multiplex network body ECU) |
| L132-11 (CANL) - L61-4 (CG) | |||
| L132-6 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | CAN No. 2 junction connector |
| L132-12 (CANL) - L61-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to Main Body ECU (Multiplex Network Body ECU) |
| *c | to CAN No. 2 Junction Connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN No. 2 junction connector main line) | B |
| NG (Main body ECU branch line) | C |
A
B
C
Disconnect the wire harness connector from the CAN No. 1 junction connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A67-1 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | ECM |
| A67-7 (CANL) - L61-4 (CG) | |||
| A67-2 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder (Skid control ECU) |
| A67-8 (CANL) - L61-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 1 Junction Connector) |
| *b | to ECM |
| *c | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (ECU or sensor bus line) | B |
A
B
Disconnect the wire harness connector from the CAN No. 3 junction connector (instrument panel wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| L133-4 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Power management control ECU |
| L133-10 (CANL) - L61-4 (CG) | |||
| L133-5 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | CAN No. 2 junction connector |
| L133-11 (CANL) - L61-4 (CG) | |||
| L133-6 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Meter circuit plate |
| L133-12 (CANL) - L61-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Power Management Control ECU |
| *c | to CAN No. 2 Junction Connector |
| *d | to Meter Circuit Plate |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (CAN No. 2 junction connector main line) | B |
| NG (ECU or sensor bus line) | C |
A
B
C
Disconnect the wire harness connector from the CAN No. 3 junction connector (engine room main wire side).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| A68-1 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Transmission control ECU assembly |
| A68-7 (CANL) - L61-4 (CG) |
| *1 | DLC3 |
| *a | Front view of wire harness connector
(to CAN No. 3 Junction Connector) |
| *b | to Transmission Control ECU Assembly |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Transmission control ECU assembly branch line) | B |
A
B
Reconnect all wire harness connectors (CAN No. 1 junction connector, CAN No. 2 junction connector and CAN No. 3 junction connector).
Disconnect the ECU or sensor connected to the CAN bus line that is shorted to ground.
If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L61-6 (CANH) - L61-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| L61-14 (CANL) - L61-4 (CG) |
| *1 | DLC3 |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
OK
NG