Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Check CAN Bus Line for Short to +B (RHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Power management control ECU

·

ECM

·

Main body ECU (Multiplex network body ECU)

·

Meter circuit plate

·

Brake booster with master cylinder assembly (Skid control ECU)

·

Spiral cable with sensor sub-assembly (Steering angle sensor)

·

Yaw rate sensor

·

Power steering ECU assembly

·

Airbag ECU assembly

·

Transmission control ECU assembly

·

Certification ECU (Smart key ECU assembly)

·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2

·

CAN No. 1 junction connector

·

CAN No. 2 junction connector

·

CAN No. 3 junction connector



*1: for Navigation receiver type

*2: for Radio and display type

WIRING DIAGRAM

C262526E03
3.958,7.958 5.688,8.146 1.729,0.188 10 false : CAN Branch Line (CANH) 3.958,8.365 5.688,8.552 1.729,0.188 10 false : CAN Branch Line (CANL) 0.833,7.969 2.75,8.156 1.917,0.188 10 false : CAN Main Bus Line (CANH) 0.833,8.385 2.75,8.573 1.917,0.188 10 false : CAN Main Bus Line (CANL) 3.469,0.479 3.885,0.667 0.417,0.188 10 false 120 Ω 2.813,1.083 3.219,1.25 0.406,0.167 10 false CANL 1.135,0.708 1.427,0.875 0.292,0.167 10 false L27 4.135,1.594 4.344,1.76 0.208,0.167 10 false SB 5.125,2.938 5.26,3.104 0.135,0.167 10 false L 2.146,5.552 2.302,5.719 0.156,0.167 10 false B 2.146,6.24 2.302,6.406 0.156,0.167 10 false W 5.052,6.823 5.24,7.083 0.188,0.26 10 false W 3.01,4.198 3.167,4.365 0.156,0.167 10 false W 5.135,5.521 5.292,5.688 0.156,0.167 10 false W 4.146,4.198 4.375,4.365 0.229,0.167 10 false GR 5.156,4.781 5.313,4.948 0.156,0.167 10 false B 3.052,1.594 3.219,1.76 0.167,0.167 10 false G 3.104,1.958 3.427,2.125 0.323,0.167 10 false L132 3.104,3.917 3.51,4.083 0.406,0.167 10 false L132 3.917,4.542 4.188,4.708 0.271,0.167 10 false L94 4.406,4.979 4.729,5.146 0.323,0.167 10 false L95 4.417,5.344 4.677,5.51 0.26,0.167 10 false L95 4.417,6.26 4.719,6.427 0.302,0.167 10 false L95 4.417,6.625 4.75,6.792 0.333,0.167 10 false L95 5.396,7.042 5.677,7.208 0.281,0.167 10 false L54 3.156,4.542 3.427,4.708 0.271,0.167 10 false L94 2.635,5.719 2.896,5.885 0.26,0.167 10 false L95 2.635,6.073 2.896,6.24 0.26,0.167 10 false L95 3.875,3.927 4.271,4.094 0.396,0.167 10 false L132 3.875,1.958 4.198,2.125 0.323,0.167 10 false L132 4.417,2.396 4.708,2.563 0.292,0.167 10 false A67 4.417,2.771 4.708,2.938 0.292,0.167 10 false A67 1.458,0.708 2.625,0.875 1.167,0.167 10 false Meter Circuit Plate 4.104,1.104 4.542,1.271 0.438,0.167 10 false CANH 6.094,5.281 6.5,5.448 0.406,0.167 10 false CANL 5.938,4.938 6.375,5.104 0.438,0.167 10 false CANH 1.063,6.208 1.469,6.375 0.406,0.167 10 false CANL 1.042,5.563 1.479,5.729 0.438,0.167 10 false CANH 5.885,6.75 6.292,6.917 0.406,0.167 10 false CANL 5.854,6.115 6.292,6.281 0.438,0.167 10 false CANH 5.906,2.25 6.344,2.417 0.438,0.167 10 false CA1H 5.896,2.885 6.333,3.052 0.438,0.167 10 false CA1L 4.073,1.344 4.281,1.51 0.208,0.167 10 false 19 2.854,3.917 3.063,4.083 0.208,0.167 10 false 11 2.729,6.271 2.833,6.438 0.104,0.167 10 false 5 2.729,5.479 2.844,5.646 0.115,0.167 10 false 6 5.625,5.469 5.833,5.635 0.208,0.167 10 false 14 5.594,2.292 5.802,2.458 0.208,0.167 10 false 37 5.594,2.885 5.802,3.052 0.208,0.167 10 false 38 4.458,4.75 4.635,4.917 0.177,0.167 10 false 15 4.5,6.823 4.708,6.99 0.208,0.167 10 false 2 4.51,6.031 4.719,6.198 0.208,0.167 10 false 3 5.073,2.229 5.281,2.396 0.208,0.167 10 false LG 2.854,1.906 3.052,2.073 0.198,0.167 10 false 12 3.042,1.354 3.24,1.521 0.198,0.167 10 false 20 4.313,3.906 4.427,4.073 0.115,0.167 10 false 5 4.479,5.542 4.656,5.708 0.177,0.167 10 false 14 5.667,4.844 5.781,5.01 0.115,0.167 10 false 6 4.26,4.5 4.375,4.667 0.115,0.167 10 false 1 2.948,4.5 3.063,4.667 0.115,0.167 10 false 2 4.302,1.906 4.417,2.073 0.115,0.167 10 false 6 4.51,2.198 4.625,2.365 0.115,0.167 10 false 1 1.604,6.188 1.719,6.354 0.115,0.167 10 false 2 1.604,5.583 1.719,5.75 0.115,0.167 10 false 3 5.635,6.729 5.75,6.896 0.115,0.167 10 false 7 5.635,6.146 5.75,6.313 0.115,0.167 10 false 1 4.521,2.979 4.708,3.146 0.188,0.167 10 false 7 5.25,0.563 6.458,0.75 1.208,0.188 10 false x: Suspected Area 5.094,3.167 5.385,3.302 0.292,0.135 10 false A58 5.417,3.167 7.135,3.719 1.719,0.552 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 6.063,5.542 6.375,5.729 0.313,0.188 10 false L61 6.354,5.542 6.75,5.729 0.396,0.188 10 false DLC3 0.896,2.813 2.885,3.313 1.99,0.5 10 false CAN No. 1 Junction Connector 0.885,5.052 2.875,5.24 1.99,0.188 10 false CAN No. 2 Junction Connector 0.24,6.49 0.531,6.646 0.292,0.156 10 false L12 0.563,6.49 1.719,6.698 1.156,0.208 10 false Yaw Rate Sensor 5.719,7.042 7.031,7.365 1.313,0.323 10 false Power Steering ECU Assembly 5.073,6.135 5.229,6.302 0.156,0.167 10 false R

C262527E08
0.781,9.031 2.698,9.219 1.917,0.188 10 false : CAN Main Bus Line (CANH) 3.969,9.052 5.688,9.24 1.719,0.188 10 false : CAN Branch Line (CANH) 3.969,9.458 5.688,9.646 1.719,0.188 10 false : CAN Branch Line (CANL) 0.781,9.427 2.698,9.615 1.917,0.188 10 false : CAN Main Bus Line (CANL) 0.802,0.469 2.792,0.656 1.99,0.188 10 false CAN No. 2 Junction Connector 0.042,8.01 2.26,8.292 2.219,0.281 10 false *1: for Navigation Receiver Type 4.427,6.406 6.417,6.594 1.99,0.188 10 false CAN No. 3 Junction Connector 0.469,3.625 1.917,3.875 1.448,0.25 10 false Airbag ECU Assembly 5.823,1.01 6.229,1.177 0.406,0.167 10 false CANL 5.813,0.406 6.25,0.573 0.438,0.167 10 false CANH 5.802,2.635 6.208,2.802 0.406,0.167 10 false CANL 5.792,2.01 6.229,2.177 0.438,0.167 10 false CANH 5.802,5.344 6.208,5.51 0.406,0.167 10 false CA1L 5.792,4.719 6.229,4.885 0.438,0.167 10 false CA1H 2.771,7.729 3.177,7.896 0.406,0.167 10 false CANL 4.073,7.74 4.51,7.906 0.438,0.167 10 false CANH 1.031,1.677 1.438,1.844 0.406,0.167 10 false CANL 1.021,1.094 1.458,1.26 0.438,0.167 10 false CANH 1.01,3.302 1.417,3.469 0.406,0.167 10 false CANL 1,2.729 1.438,2.896 0.438,0.167 10 false CANH 4.385,0.521 4.667,0.688 0.281,0.167 10 false L94 4.385,0.896 4.667,1.063 0.281,0.167 10 false L94 4.375,2.177 4.635,2.344 0.26,0.167 10 false L95 4.375,2.531 4.625,2.698 0.25,0.167 10 false L95 3.115,3.5 3.385,3.667 0.271,0.167 10 false L94 3.875,3.5 4.146,3.667 0.271,0.167 10 false L94 3.063,4.135 3.385,4.302 0.323,0.167 10 false L133 3.104,6.875 3.458,7.042 0.354,0.167 10 false A68 3.854,6.875 4.229,7.042 0.375,0.167 10 false A68 3.823,4.135 4.229,4.302 0.406,0.167 10 false L133 2.594,1.198 2.844,1.365 0.25,0.167 10 false L94 2.594,1.563 2.854,1.729 0.26,0.167 10 false L94 2.594,2.833 2.854,3 0.26,0.167 10 false L95 2.594,3.198 2.854,3.365 0.26,0.167 10 false L95 1.531,1.094 1.646,1.26 0.115,0.167 10 false 9 2.677,1.781 2.792,1.948 0.115,0.167 10 false 8 2.688,0.979 2.802,1.146 0.115,0.167 10 false 7 2.052,1.01 2.167,1.177 0.115,0.167 10 false B 2.052,1.698 2.219,1.865 0.167,0.167 10 false W 1.5,1.677 1.677,1.844 0.177,0.167 10 false 10 1.5,2.729 1.688,2.896 0.188,0.167 10 false 13 2.667,3.385 2.781,3.552 0.115,0.167 10 false 8 4.229,3.5 4.344,3.667 0.115,0.167 10 false 4 2.896,3.5 3.01,3.667 0.115,0.167 10 false 5 2.656,2.615 2.771,2.781 0.115,0.167 10 false 9 2.031,2.646 2.146,2.813 0.115,0.167 10 false B 2.021,3.354 2.177,3.521 0.156,0.167 10 false W 1.5,3.302 1.688,3.469 0.188,0.167 10 false 22 0.073,1.958 0.333,2.125 0.26,0.167 10 false L62 5.604,0.406 5.719,0.573 0.115,0.167 10 false 4 4.406,1.104 4.594,1.271 0.188,0.167 10 false 11 4.417,2.74 4.604,2.906 0.188,0.167 10 false 11 4.417,1.938 4.604,2.104 0.188,0.167 10 false 12 2.844,4.125 3.031,4.292 0.188,0.167 10 false 12 2.896,6.885 3.083,7.052 0.188,0.167 10 false 7 4.229,4.125 4.417,4.292 0.188,0.167 10 false 6 4.229,6.885 4.417,7.052 0.188,0.167 10 false 1 4.406,0.302 4.594,0.469 0.188,0.167 10 false 10 4.979,0.375 5.125,0.542 0.146,0.167 10 false B 4.979,1.073 5.167,1.24 0.188,0.167 10 false W 4.979,2 5.125,2.167 0.146,0.167 10 false B 4.979,2.708 5.125,2.875 0.146,0.167 10 false W 4.073,7.271 4.198,7.438 0.125,0.167 10 false P 2.99,7.271 3.135,7.438 0.146,0.167 10 false V 5.604,1.01 5.729,1.177 0.125,0.167 10 false 3 5.563,2.052 5.75,2.219 0.188,0.167 10 false 9 5.552,2.635 5.74,2.802 0.188,0.167 10 false 10 5.531,4.74 5.719,4.906 0.188,0.167 10 false 16 4.469,4.646 4.656,4.813 0.188,0.167 10 false 2 4.469,5.417 4.656,5.583 0.188,0.167 10 false 8 4.927,5.438 5.146,5.604 0.219,0.167 10 false BR 4.958,4.719 5.094,4.885 0.135,0.167 10 false Y 5.542,5.344 5.729,5.51 0.188,0.167 10 false 15 4.052,7.51 4.24,7.677 0.188,0.167 10 false 13 3.073,7.51 3.177,7.677 0.104,0.167 10 false 5 0.167,3.625 0.448,3.792 0.281,0.167 10 false L16 4.375,4.865 4.656,5.031 0.281,0.167 10 false A68 4.375,5.229 4.656,5.396 0.281,0.167 10 false A68 5.333,5.615 5.615,5.781 0.281,0.167 10 false A24 5.073,2.917 5.354,3.083 0.281,0.167 10 false L38 0.083,7.625 1.292,7.813 1.208,0.188 10 false x: Suspected Area 3.438,8.479 3.948,8.667 0.51,0.188 10 false 120 Ω 0.365,1.958 2.125,2.333 1.76,0.375 10 false Certification ECU (Smart Key ECU Assembly) 5.385,2.917 6.406,3.323 1.021,0.406 10 false Navigation ECU Sub-assembly*1 4.667,1.292 4.958,1.469 0.292,0.177 10 false L51 4.99,1.292 7.073,1.844 2.083,0.552 10 false Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor) 5.646,5.615 6.99,6.292 1.344,0.677 10 false Transmission Control ECU Assembly 4.76,8.198 5.031,8.396 0.271,0.198 10 false A57 5.083,8.198 5.427,8.396 0.344,0.198 10 false ECM 4.115,3.833 4.24,4 0.125,0.167 10 false B 2.958,3.833 3.104,4 0.146,0.167 10 false W 0.313,5.292 1.656,5.802 1.344,0.51 10 false Power Management Control ECU 1.021,5.021 1.427,5.188 0.406,0.167 10 false CA1L 1.01,4.396 1.448,4.563 0.438,0.167 10 false CA1H 2.01,5.083 2.156,5.25 0.146,0.167 10 false P 2.01,4.344 2.156,4.51 0.146,0.167 10 false V 2.552,4.531 2.927,4.698 0.375,0.167 10 false L133 2.552,4.896 2.917,5.063 0.365,0.167 10 false L133 0.073,5.292 0.313,5.458 0.24,0.167 10 false L6 2.667,4.323 2.854,4.49 0.188,0.167 10 false 4 2.625,5.115 2.813,5.281 0.188,0.167 10 false 10 1.5,4.427 1.688,4.594 0.188,0.167 10 false 25 1.5,5.021 1.688,5.188 0.188,0.167 10 false 24 5.385,3.542 7.073,3.99 1.688,0.448 10 false Radio and Display Receiver Assembly*2 0.042,8.406 2.823,8.688 2.781,0.281 10 false *2: for Radio and Display Receiver Type 5.073,3.552 5.354,3.719 0.281,0.167 10 false L35 0.313,6.927 1.948,7.302 1.635,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 1.01,6.656 1.417,6.823 0.406,0.167 10 false CANL 1,6.031 1.438,6.198 0.438,0.167 10 false CANH 2.021,6.708 2.177,6.875 0.156,0.167 10 false R 2.01,5.979 2.25,6.146 0.24,0.167 10 false SB 2.552,6.167 2.927,6.333 0.375,0.167 10 false L133 2.552,6.531 2.917,6.698 0.365,0.167 10 false L133 0.073,6.927 0.344,7.094 0.271,0.167 10 false L7 2.667,5.958 2.854,6.125 0.188,0.167 10 false 5 2.625,6.729 2.813,6.896 0.188,0.167 10 false 11 1.531,6.073 1.719,6.24 0.188,0.167 10 false 14 1.531,6.646 1.719,6.813 0.188,0.167 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the cruise control system on using the cruise control switch (ON/OFF switch), wait at least 60 seconds, and then drive the vehicle at a speed of 50 km/h (31 mph) or more for at least 1.72 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 J/C)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191024E02
2.781,4.281 2.688,4.281 2.688,4.281 2.448,4.135 false 0.75,0.927 0.99,0.927 0.99,0.927 1.552,1.208 false 0.75,1.208 0.99,1.208 0.99,1.208 1.542,1.417 false 0.75,2.25 1.177,2.25 1.177,2.25 1.583,1.865 false 0.75,1.885 1.177,1.885 1.177,1.885 1.573,1.667 false 2.615,2.188 2.104,2.188 2.104,2.188 1.719,1.854 false 2.615,1.885 2.104,1.885 2.104,1.885 1.76,1.656 false 2.656,0.927 2.135,0.927 2.135,0.927 1.74,1.208 false 2.656,1.208 2.427,1.208 2.427,1.208 1.74,1.427 false 0.083,0.094 0.469,0.365 0.385,0.271 10 false *a 0.104,2.979 0.354,3.229 0.25,0.25 10 false *1 0.104,0.833 0.719,1.115 0.615,0.281 10 false CANH*b 0.125,1.802 0.667,1.979 0.542,0.177 10 false CANH*d 0.135,2.167 0.677,2.344 0.542,0.177 10 false CANH*e 0.115,1.146 0.656,1.323 0.542,0.177 10 false CANH*c 2.698,0.854 3.313,1.104 0.615,0.25 10 false CANL*b 2.698,1.781 3.24,1.958 0.542,0.177 10 false CANL*d 2.698,2.094 3.24,2.271 0.542,0.177 10 false CANL*e 2.698,1.135 3.24,1.313 0.542,0.177 10 false CANL*c 1.583,0.177 2.021,0.417 0.438,0.24 10 false L94 0.229,3.688 0.594,3.927 0.365,0.24 10 false L61 2.823,4.208 3.115,4.385 0.292,0.177 10 false BAT

Disconnect the wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder left side).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L94-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 1 junction connector
L94-2 (CANL) - L61-16 (BAT)
L94-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 3 junction connector
L94-5 (CANL) - L61-16 (BAT)
L94-7 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Certification ECU (Smart key ECU assembly)
L94-8 (CANL) - L61-16 (BAT)
L94-10 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Spiral cable with sensor sub-assembly (Steering angle sensor)
L94-11 (CANL) - L61-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 1 Junction Connector
*c to CAN No. 3 Junction Connector
*d to Certification ECU (Smart Key ECU Assembly)
*e to Spiral Cable with Sensor Sub-assembly (Steering Angle Sensor)

Result:
Result Proceed to
OK A
NG (CAN No. 1 junction connector main line) B
NG (CAN No. 3 junction connector main line) C
NG (ECU or sensor bus line) D




A

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 J/C)

B

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 J/C)

C

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 J/C)

D

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 2 J/C)
a.
U191025E02
2.781,4.271 2.688,4.271 2.688,4.271 2.448,4.125 false 0.75,0.938 0.99,0.938 0.99,0.938 1.708,1.219 false 0.75,1.208 0.99,1.208 0.99,1.208 1.698,1.417 false 0.729,2.24 1.156,2.24 1.156,2.24 1.719,1.854 false 0.729,1.885 1.156,1.885 1.156,1.885 1.708,1.667 false 2.583,2.177 2.073,2.177 2.073,2.177 1.844,1.844 false 2.583,1.875 2.073,1.875 2.073,1.875 1.875,1.646 false 2.625,0.958 2.135,0.958 2.135,0.958 1.896,1.24 false 2.625,1.219 2.427,1.219 2.427,1.219 1.896,1.438 false 0.708,2.583 1.021,2.583 1.021,2.583 1.708,2.031 false 2.615,2.531 2.25,2.531 2.25,2.531 1.844,2.042 false 0.146,0.115 0.49,0.281 0.344,0.167 10 false *a 0.104,3.01 0.26,3.188 0.156,0.177 10 false *1 2.688,0.885 3.229,1.063 0.542,0.177 10 false CANH*b 2.667,1.792 3.208,1.969 0.542,0.177 10 false CANH*d 2.667,2.083 3.208,2.26 0.542,0.177 10 false CANH*e 2.677,1.156 3.219,1.333 0.542,0.177 10 false CANH*c 0.198,0.854 0.74,1.031 0.542,0.177 10 false CANL*b 0.188,1.792 0.729,1.969 0.542,0.177 10 false CANL*d 0.198,2.146 0.74,2.323 0.542,0.177 10 false CANL*e 0.188,1.125 0.729,1.302 0.542,0.177 10 false CANL*c 1.604,0.177 2.021,0.375 0.417,0.198 10 false L95 0.229,3.667 0.542,3.844 0.313,0.177 10 false L61 2.823,4.198 3.115,4.375 0.292,0.177 10 false BAT 2.677,2.448 3.219,2.625 0.542,0.177 10 false CANH*f 0.208,2.51 0.75,2.688 0.542,0.177 10 false CANL*f

Disconnect the wire harness connector from the CAN No. 2 junction connector (instrument panel connector holder right side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L95-3 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power steering ECU assembly
L95-2 (CANL) - L61-16 (BAT)
L95-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Yaw rate sensor
L95-5 (CANL) - L61-16 (BAT)
L95-9 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Airbag ECU assembly
L95-8 (CANL) - L61-16 (BAT)
L95-12 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
·

Navigation ECU sub-assembly*1

·

Radio and display receiver assembly*2


L95-11 (CANL) - L61-16 (BAT)
L95-15 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher DLC3
L95-14 (CANL) - L61-16 (BAT)


*1: for Navigation receiver type

*2: for Radio and display type

Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to Power Steering ECU Assembly
*c to Yaw Rate Sensor
*d to Airbag ECU Assembly
*e
·

Navigation ECU Sub-assembly*1

·

Radio and Display Receiver Assembly*2


*f to DLC3

*1: for Navigation receiver type

*2: for Radio and display type

Result:
Result Proceed to
OK A
NG (ECU or sensor branch line) B
NG (DLC3 bus line) C




A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 J/C)
a.
U154822E03
2.427,4.073 2.688,4.25 2.688,4.25 2.865,4.25 false 2.031,1.479 2.031,0.667 2.031,0.667 1.833,0.667 false 2,1.813 2,2.396 2,2.396 1.74,2.396 false 2.177,1.49 2.177,0.667 2.177,0.667 2.375,0.667 false 2.167,1.802 2.167,2.396 2.167,2.396 2.427,2.396 false 0.115,2.729 0.365,2.969 0.25,0.24 10 false *1 0.115,0.115 0.365,0.354 0.25,0.24 10 false *a 1.188,0.573 1.875,0.823 0.688,0.25 10 false CANH*b 1.156,2.302 1.844,2.552 0.688,0.25 10 false CANL*b 2.438,0.583 3.125,0.833 0.688,0.25 10 false CANH*c 2.49,2.302 3.177,2.552 0.688,0.25 10 false CANL*c 2.917,4.156 3.271,4.354 0.354,0.198 10 false BAT 0.229,3.75 0.646,4 0.417,0.25 10 false L61 0.344,1.49 0.76,1.74 0.417,0.25 10 false L132

Disconnect the wire harness connector from the CAN No. 1 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L132-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 2 junction connector
L132-11 (CANL) - L61-16 (BAT)
L132-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Meter circuit plate
L132-12 (CANL) - L61-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to CAN No. 2 Junction Connector
*c to Meter Circuit Plate

Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (Meter circuit plate main line) C




A

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 J/C)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 1 J/C - CAN NO. 2 J/C)

C

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
4.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 1 J/C)
a.
U191047E02
2.438,4.125 2.698,4.302 2.698,4.302 2.875,4.302 false 1.292,1.469 1.292,0.656 1.292,0.656 1.094,0.656 false 1.292,1.844 1.292,2.469 1.292,2.469 1.031,2.469 false 0.094,2.885 0.344,3.125 0.25,0.24 10 false *1 0.083,0.083 0.333,0.323 0.25,0.24 10 false *a 0.563,0.573 1.25,0.823 0.688,0.25 10 false CANH*b 0.521,2.385 1.208,2.635 0.688,0.25 10 false CANL*b 2.917,4.208 3.271,4.406 0.354,0.198 10 false BAT 0.219,3.771 0.635,4.021 0.417,0.25 10 false L61 0.385,1.49 0.802,1.74 0.417,0.25 10 false A67

Disconnect the wire harness connector from the CAN No. 1 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A67-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (Skid control ECU)
A67-7 (CANL) - L61-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to Brake Booster with Master Cylinder Assembly (Skid Control ECU)

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B




A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
5.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 J/C)
a.
U191051E02
2.438,4.115 2.698,4.292 2.698,4.292 2.875,4.292 false 1.813,1.49 1.813,0.677 1.813,0.677 1.615,0.677 false 1.823,1.823 1.823,2.448 1.823,2.448 1.563,2.448 false 2.177,1.479 2.177,0.656 2.177,0.656 2.385,0.656 false 2.177,1.833 2.177,2.458 2.177,2.458 2.438,2.458 false 1.99,1.479 1.99,0.333 1.99,0.333 1.698,0.333 false 2,1.823 2,2.76 2,2.76 1.771,2.76 false 0.146,2.875 0.396,3.115 0.25,0.24 10 false *1 0.135,0.188 0.385,0.427 0.25,0.24 10 false *a 1.073,0.594 1.76,0.844 0.688,0.25 10 false CANH*b 1.042,2.365 1.729,2.615 0.688,0.25 10 false CANL*b 2.917,4.198 3.271,4.396 0.354,0.198 10 false BAT 0.177,3.76 0.594,4.01 0.417,0.25 10 false L61 0.344,1.49 0.76,1.74 0.417,0.25 10 false L133 2.438,0.573 3.042,0.823 0.604,0.25 10 false CANH*d 2.49,2.375 3.073,2.625 0.583,0.25 10 false CANL*d 1.177,0.25 1.74,0.5 0.563,0.25 10 false CANH*c 1.26,2.677 1.813,2.927 0.552,0.25 10 false CANL*c

Disconnect the wire harness connector from the CAN No. 3 junction connector (instrument panel wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
L133-4 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power management control ECU
L133-10 (CANL) - L61-16 (BAT)
L133-5 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Main body ECU (Multiplex network body ECU)
L133-11 (CANL) - L61-16 (BAT)
L133-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher CAN No. 2 junction connector
L133-12 (CANL) - L61-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to Power Management Control ECU
*c to Main Body ECU (Multiplex Network Body ECU)
*d to CAN No. 2 Junction Connector

Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main line) B
NG (ECU or sensor bus line) C




A

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 J/C)

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 J/C - CAN NO. 3 J/C)

C

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
6.CHECK FOR SHORT TO +B IN CAN BUS LINE (CAN NO. 3 J/C)
a.
U191048E02
2.427,4.104 2.688,4.281 2.688,4.281 2.865,4.281 false 1.281,1.479 1.281,0.667 1.281,0.667 1.083,0.667 false 1.292,1.833 1.292,2.458 1.292,2.458 1.031,2.458 false 1.479,1.458 1.479,0.646 1.479,0.646 1.677,0.646 false 1.469,1.833 1.469,2.458 1.469,2.458 1.729,2.458 false 0.094,2.906 0.344,3.146 0.25,0.24 10 false *1 0.042,0.208 0.292,0.448 0.25,0.24 10 false *a 0.552,0.594 1.24,0.844 0.688,0.25 10 false CANH*b 0.521,2.375 1.208,2.625 0.688,0.25 10 false CANL*b 2.917,4.198 3.271,4.396 0.354,0.198 10 false BAT 0.208,3.771 0.625,4.021 0.417,0.25 10 false L61 0.375,1.49 0.792,1.74 0.417,0.25 10 false A68 1.729,0.563 2.417,0.813 0.688,0.25 10 false CANH*c 1.771,2.375 2.458,2.625 0.688,0.25 10 false CANL*c

Disconnect the wire harness connector from the CAN No. 3 junction connector (engine room main wire side).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A68-1 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A68-7 (CANL) - L61-16 (BAT)
A68-2 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Transmission control ECU assembly
A68-8 (CANL) - L61-16 (BAT)


Text in Illustration
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to ECM
*c to Transmission Control ECU Assembly

Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B




A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
7.CHECK FOR SHORT TO +B IN CONNECTED COMPONENT (ECU, SENSOR)
a.

Reconnect all wire harness connectors (CAN No. 1 junction connector, CAN No. 2 junction connector and CAN No. 3 junction connector).


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to the terminals of ECU tables (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>TERMINALS OF ECU).



c.
U154763E03
2.052,1.865 2.417,1.313 false 2.052,2.552 1.823,2.927 false 2.49,2.542 2.76,2.906 false 0.135,0.198 0.979,0.531 0.844,0.333 10 false *1 1.646,0.792 2.052,1.01 0.406,0.219 10 false L61 2.438,1.104 2.844,1.281 0.406,0.177 10 false CANH 1.531,2.948 1.917,3.125 0.385,0.177 10 false CANL 2.708,2.948 3.094,3.125 0.385,0.177 10 false BAT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-6 (CANH) - L61-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
L61-14 (CANL) - L61-16 (BAT)


Text in Illustration
*1 DLC3

HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR