Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here)).

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here)).


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C353280E04
2.917,0.458 3.083,0.458 3.083,0.458 3.083,1.292 false 2.229,0.948 2.396,0.948 2.396,0.948 2.396,1.281 false 4.969,0.781 4.802,0.781 4.802,0.781 4.802,1.281 false 1.448,5.021 3.406,5.344 1.958,0.323 10 false : CAN Main Bus Line (CANH) 1.448,5.427 3.458,5.74 2.01,0.313 10 false : CAN Main Bus Line (CANL) 4.417,5.01 6.458,5.292 2.042,0.281 10 false : CAN Branch Line (CANH) 4.417,5.417 6.417,5.708 2,0.292 10 false : CAN Branch Line (CANL) 2.448,4.219 4.74,4.563 2.292,0.344 10 false Air Conditioning Amplifier Assembly 2.146,4.219 2.458,4.469 0.313,0.25 10 false L17 3.844,3.74 4.177,3.906 0.333,0.167 10 false GND 4.229,3.625 4.563,3.792 0.333,0.167 10 false 14 3.083,3.438 3.5,3.604 0.417,0.167 10 false CANH 3.5,3.438 3.917,3.604 0.417,0.167 10 false CANL 2.802,3.51 3.135,3.677 0.333,0.167 10 false B 2.802,3.844 3.135,4.01 0.333,0.167 10 false IG+ 2.563,3.406 2.896,3.573 0.333,0.167 10 false 21 2.604,3.74 2.938,3.906 0.333,0.167 10 false 1 1.885,3.646 2.552,3.813 0.667,0.167 10 false ECU-B3 2.01,3.979 2.677,4.146 0.667,0.167 10 false A/C 3.063,3.219 3.396,3.385 0.333,0.167 10 false 11 3.729,3.219 4.063,3.385 0.333,0.167 10 false 12 0.688,2.229 1.354,2.396 0.667,0.167 10 false 120 Ω 6.125,2.219 6.792,2.385 0.667,0.167 10 false 120 Ω 3.979,0.594 4.479,0.76 0.5,0.167 10 false DLC3 0.604,2.823 1.167,3.063 0.563,0.24 10 false ECM 5.76,2.833 6.958,3.354 1.198,0.521 10 false Combination Meter Sub-assembly 0.323,0.875 2.302,1.167 1.979,0.292 10 false CAN No. 1 Junction Connector 1,0.385 2.948,0.719 1.948,0.333 10 false CAN No. 2 Junction Connector 5.063,0.708 7.063,1.042 2,0.333 10 false CAN No. 3 Junction Connector 5.219,3.792 6.49,4.125 1.271,0.333 10 false Trouble Area 0.094,0.073 1.344,0.542 1.25,0.469 12 false V Bus (for LHD):

C353280E05
2.917,0.458 3.083,0.458 3.083,0.458 3.083,1.292 false 2.229,0.948 2.396,0.948 2.396,0.948 2.396,1.281 false 4.969,0.781 4.802,0.781 4.802,0.781 4.802,1.281 false 1.448,5.021 3.406,5.344 1.958,0.323 10 false : CAN Main Bus Line (CANH) 1.448,5.427 3.458,5.74 2.01,0.313 10 false : CAN Main Bus Line (CANL) 4.417,5.01 6.458,5.292 2.042,0.281 10 false : CAN Branch Line (CANH) 4.417,5.417 6.417,5.708 2,0.292 10 false : CAN Branch Line (CANL) 2.448,4.219 4.74,4.563 2.292,0.344 10 false Air Conditioning Amplifier Assembly 2.146,4.219 2.458,4.469 0.313,0.25 10 false L17 3.844,3.74 4.177,3.906 0.333,0.167 10 false GND 4.229,3.625 4.563,3.792 0.333,0.167 10 false 14 3.083,3.438 3.5,3.604 0.417,0.167 10 false CANH 3.5,3.438 3.917,3.604 0.417,0.167 10 false CANL 2.802,3.51 3.135,3.677 0.333,0.167 10 false B 2.802,3.844 3.135,4.01 0.333,0.167 10 false IG+ 2.563,3.406 2.896,3.573 0.333,0.167 10 false 21 2.604,3.74 2.938,3.906 0.333,0.167 10 false 1 1.885,3.646 2.552,3.813 0.667,0.167 10 false ECU-B3 2.01,3.979 2.677,4.146 0.667,0.167 10 false A/C 3.063,3.219 3.396,3.385 0.333,0.167 10 false 11 3.729,3.219 4.063,3.385 0.333,0.167 10 false 12 0.688,2.229 1.354,2.396 0.667,0.167 10 false 120 Ω 6.125,2.219 6.792,2.385 0.667,0.167 10 false 120 Ω 3.979,0.594 4.479,0.76 0.5,0.167 10 false DLC3 0.604,2.823 1.167,3.063 0.563,0.24 10 false ECM 5.76,2.833 6.958,3.354 1.198,0.521 10 false Combination Meter Sub-assembly 0.333,0.865 2.313,1.156 1.979,0.292 10 false CAN No. 3 Junction Connector 1.01,0.375 2.958,0.708 1.948,0.333 10 false CAN No. 2 Junction Connector 5.063,0.708 7.063,1.042 2,0.333 10 false CAN No. 1 Junction Connector 5.219,3.792 6.49,4.125 1.271,0.333 10 false Trouble Area 0.094,0.073 1.344,0.542 1.25,0.469 12 false V Bus (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191097E01
0.156,0.149 0.358,0.357 0.202,0.207 10 *a 0.927,0.571 1.388,0.768 0.461,0.196 10 CANH 2.29,0.568 2.750,0.765 0.461,0.196 10 CANL 1.464,0.655 1.815,0.655 1.815,0.655 1.815,2.13 false 2.258,0.657 1.935,0.657 1.935,0.657 1.935,2.133 false 0.515,1.203 0.797,1.384 0.281,0.181 10 L17

Disconnect the L17 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-11 (CANH) - L17-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191098E03
0.927,1.229 0.646,1.229 0.646,1.229 0.646,2.104 false 2.469,1.229 2.146,1.229 2.146,1.229 2.146,2.115 false 0.646,2.375 0.646,2.823 0.646,2.823 0.823,2.823 false 0.156,0.083 0.354,0.292 0.198,0.208 10 false *a 2.521,1.156 2.958,1.385 0.438,0.229 10 false GND 1,1.146 1.375,1.385 0.375,0.24 10 false IG+ 1.115,0.688 1.51,0.979 0.396,0.292 10 false L17 0.865,2.729 1.104,2.948 0.24,0.219 10 false B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-14 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)

b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L17-1 (IG+) - Body ground Power switch on (IG) 11 to 14 V
L17-21 (B) - Body ground Power switch off 11 to 14 V




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)