Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2017.12
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Navigation ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Navigation ECU Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on the CAN Bus Check screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that correspond to "Navigation ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here))


·

Navigation receiver assembly branch line or connector

·

Power source circuit of navigation receiver assembly

·

Navigation receiver assembly ground circuit

·

Navigation receiver assembly



WIRING DIAGRAM

C243471E14
4.479,0.24 4.198,0.24 4.198,0.24 3.677,1.146 false 2.042,0.771 2.135,0.771 2.135,0.771 2.281,1.146 false 5.146,0.604 5.063,0.604 5.063,0.604 4.917,1.135 false 2.885,0.417 3.302,0.583 0.417,0.167 10 false DLC3 5.719,3.354 6.604,3.698 0.885,0.344 10 false Trouble Area 0.292,2.688 1.521,3.083 1.229,0.396 10 false Combination Meter Sub-assembly 4.531,0.146 6.542,0.354 2.01,0.208 10 false CAN No. 2 Junction Connector 6.198,2.063 6.594,2.24 0.396,0.177 10 false 120 Ω 0.677,2.063 1.073,2.24 0.396,0.177 10 false 120 Ω 1.427,5.125 3.344,5.448 1.917,0.323 10 false : CAN Main Bus Line (CANH) 1.427,5.417 3.344,5.74 1.917,0.323 10 false : CAN Main Bus Line (CANL) 4.417,5.125 6.177,5.448 1.76,0.323 10 false : CAN Branch Line (CANH) 4.417,5.427 6.104,5.75 1.688,0.323 10 false : CAN Branch Line (CANL) 3.75,3.146 4.229,3.323 0.479,0.177 10 false CANH 4.208,3.146 4.667,3.323 0.458,0.177 10 false CANL 3.458,3.5 3.688,3.677 0.229,0.177 10 false IG 3.469,3.896 3.875,4.073 0.406,0.177 10 false ACC1 4.438,3.469 4.854,3.635 0.417,0.167 10 false GND1 3.802,2.719 3.917,2.875 0.115,0.156 10 false 9 4.375,2.719 4.542,2.896 0.167,0.177 10 false 10 4.979,3.25 5.104,3.427 0.125,0.177 10 false 7 2.083,3.667 3.042,3.844 0.958,0.177 10 false ECU-IG NO. 2 2.208,4.052 3.188,4.229 0.979,0.177 10 false ECU-ACC 0.083,0.688 2.052,0.885 1.969,0.198 10 false CAN No. 1 Junction Connector 2.667,4.396 4.938,4.813 2.271,0.417 10 false Navigation Receiver Assembly 3.125,3.5 3.479,3.667 0.354,0.167 10 false L38 6.198,2.698 6.552,2.896 0.354,0.198 10 false ECM 3.823,2.917 4.177,3.083 0.354,0.167 10 false L38 4.219,2.917 4.573,3.083 0.354,0.167 10 false L38 3.094,3.885 3.448,4.052 0.354,0.167 10 false L171 4.875,3.479 5.229,3.646 0.354,0.167 10 false L171 3.198,3.323 3.313,3.479 0.115,0.156 10 false 1 3.198,3.698 3.313,3.854 0.115,0.156 10 false 3 3.448,3.135 3.75,3.313 0.302,0.177 10 false +B1 3.094,3.125 3.448,3.292 0.354,0.167 10 false L171 3.198,2.906 3.313,3.063 0.115,0.156 10 false 4 5.188,0.531 7.135,0.76 1.948,0.229 10 false CAN No. 3 Junction Connector 0.104,0.063 1.375,0.292 1.271,0.229 12 false V Bus (for RHD): 2.177,3.292 3.042,3.469 0.865,0.177 10 false RAD NO. 1

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (NAVIGATION RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154926E02
1.552,0.573 1.802,0.573 1.802,0.573 1.802,1.896 false 2.135,0.563 1.917,0.563 1.917,0.563 1.917,1.896 false 0.135,0.135 0.344,0.323 0.208,0.188 10 false *a 2.198,0.49 2.646,0.688 0.448,0.198 10 false CANL 1.094,0.49 1.542,0.688 0.448,0.198 10 false CANH 0.458,1.156 0.781,1.323 0.323,0.167 10 false L38

Disconnect the L38 navigation receiver assembly connector.

Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L38-9 (CANH) - L38-10 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (NAVIGATION RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U191106E02
1.49,3.802 1.49,4.135 1.49,4.135 1.344,4.135 true 1.833,3.5 1.833,2.74 1.833,2.74 2,2.74 true 0.823,1.646 0.823,1.156 0.823,1.156 0.667,1.156 true 2.031,3.531 2.365,3.531 true 0.167,0.073 0.344,0.26 0.177,0.188 10 false *a 0.5,1.073 0.729,1.26 0.229,0.188 10 false IG 2.052,2.656 2.479,2.833 0.427,0.177 10 false ACC1 0.833,4.042 1.26,4.219 0.427,0.177 10 false GND1 0.229,1.51 0.531,1.688 0.302,0.177 10 false L38 2.427,3.448 2.76,3.625 0.333,0.177 10 false +B1 0.281,3.594 0.708,3.771 0.427,0.177 10 false L171

Disconnect the navigation L171 navigation receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Text in Illustration
*a Front view of wire harness connector
(to Navigation Receiver Assembly)

Standard Resistance:
Tester Connection Condition Specified Condition
L171-7 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L171-4 (+B1) - Body ground power switch off 11 to 14 V
L171-3 (ACC1) - Body ground Power switch on (ACC) 11 to 14 V
L38-1 (IG) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)