Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2016.05–2020.08
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Transmission Control ECU Communication Stop Mode  


DESCRIPTION

The transmission control ECU assembly drives the parking lock actuator in accordance with signals from the power management control ECU.

Detection Item Symptom Trouble Area
Transmission Control ECU Communication Stop Mode Either condition is met:
·

"Transmission Control " is not displayed on the CAN Bus Check screen of the GTS (See page (Click here))

·

Communication system DTCs (DTCs that start with U) that correspond to "Transmission Control ECU Communication Stop Mode" in "DTC Combination Table" are output (See page (Click here))


·

Transmission control ECU assembly branch line or connector

·

Power source circuit of transmission control ECU assembly

·

Transmission control ECU assembly ground circuit

·

Transmission control ECU assembly



WIRING DIAGRAM

C240422E26
5.073,0.781 4.875,0.781 4.875,0.781 4.698,1.156 false 3.25,0.792 3.427,0.792 3.427,0.792 3.635,1.156 false 5.052,2.656 5.198,3.469 5.198,3.469 5.479,3.469 false 6.24,2.708 6.615,2.969 0.375,0.26 10 false ECM 2.146,3.979 4.5,4.667 2.354,0.688 10 false Transmission Control ECU Assembly 4.271,0.406 4.646,0.583 0.375,0.177 10 false DLC3 0.26,2.698 1.438,3.24 1.177,0.542 10 false Combination Meter Sub-assembly 1.427,5.01 3.354,5.365 1.927,0.354 10 false : CAN Main Bus Line (CANH) 4.396,5.042 6.104,5.396 1.708,0.354 10 false : CAN Branch Line (CANH) 4.396,5.427 6.104,5.781 1.708,0.354 10 false : CAN Branch Line (CANL) 1.427,5.417 3.354,5.771 1.927,0.354 10 false : CAN Main Bus Line (CANL) 1.49,3.604 2.292,3.896 0.802,0.292 10 false IGCT NO. 2 2.635,3.438 3.167,3.75 0.531,0.313 10 false +B 5.104,0.719 7.115,1.063 2.01,0.344 10 false CAN No. 2 Junction Connector 5.542,3.385 6.76,3.792 1.219,0.406 10 false CAN No. 1 Junction Connector 0.438,3.594 1.313,3.854 0.875,0.26 10 false Trouble Area 3.802,3.417 4.021,3.594 0.219,0.177 10 false E1 2.844,3.167 3.313,3.344 0.469,0.177 10 false CA1H 3.396,3.167 3.865,3.344 0.469,0.177 10 false CA1L 2.333,3.24 2.5,3.417 0.167,0.177 10 false 16 4.146,3.229 4.313,3.406 0.167,0.177 10 false 1 2.833,2.813 3,2.99 0.167,0.177 10 false 16 3.625,2.823 3.792,3 0.167,0.177 10 false 15 2.979,2.958 3.26,3.135 0.281,0.177 10 false A24 2.281,3.438 2.594,3.615 0.313,0.177 10 false A23 1.313,0.688 3.271,1.042 1.958,0.354 10 false CAN No. 3 Junction Connector 3.375,2.958 3.677,3.135 0.302,0.177 10 false A24 4.073,3.417 4.375,3.594 0.302,0.177 10 false A24 0.708,2.083 1.104,2.26 0.396,0.177 10 false 120 Ω 6.188,2.083 6.583,2.26 0.396,0.177 10 false 120 Ω 0.125,0.094 1.458,0.406 1.333,0.313 12 false V Bus (for LHD):

C240422E27
5.073,0.781 4.875,0.781 4.875,0.781 4.698,1.156 false 3.25,0.792 3.427,0.792 3.427,0.792 3.635,1.156 false 5.052,2.656 5.198,3.469 5.198,3.469 5.479,3.469 false 0.729,2.698 1.104,2.958 0.375,0.26 10 false ECM 2.25,3.969 5.24,4.323 2.99,0.354 10 false Transmission Control ECU Assembly 4.271,0.406 4.646,0.583 0.375,0.177 10 false DLC3 5.802,2.698 6.99,3.24 1.188,0.542 10 false Combination Meter Sub-assembly 1.427,5 3.354,5.354 1.927,0.354 10 false : CAN Main Bus Line (CANH) 4.396,5.01 6.104,5.365 1.708,0.354 10 false : CAN Branch Line (CANH) 4.396,5.417 6.104,5.771 1.708,0.354 10 false : CAN Branch Line (CANL) 1.427,5.396 3.354,5.75 1.927,0.354 10 false : CAN Main Bus Line (CANL) 1.49,3.594 2.281,3.875 0.792,0.281 10 false IGCT NO. 2 2.635,3.417 3.167,3.729 0.531,0.313 10 false +B 5.104,0.719 7.115,1.063 2.01,0.344 10 false CAN No. 2 Junction Connector 1.271,0.708 3.292,1.052 2.021,0.344 10 false CAN No. 3 Junction Connector 0.438,3.573 1.313,3.833 0.875,0.26 10 false Trouble Area 3.781,3.417 4.219,3.594 0.438,0.177 10 false E1 2.875,3.156 3.344,3.333 0.469,0.177 10 false CA1H 3.385,3.167 3.854,3.344 0.469,0.177 10 false CA1L 2.333,3.26 2.5,3.438 0.167,0.177 10 false 16 4.146,3.229 4.313,3.406 0.167,0.177 10 false 1 2.833,2.792 3,2.969 0.167,0.177 10 false 16 3.604,2.813 3.771,2.99 0.167,0.177 10 false 15 5.531,3.385 6.813,3.74 1.281,0.354 10 false CAN No. 1 Junction Connector 0.677,2.073 1.073,2.25 0.396,0.177 10 false 120 Ω 6.177,2.083 6.573,2.26 0.396,0.177 10 false 120 Ω 2.271,3.438 2.573,3.615 0.302,0.177 10 false A23 3.375,2.948 3.677,3.125 0.302,0.177 10 false A24 2.979,2.948 3.281,3.125 0.302,0.177 10 false A24 4.073,3.417 4.375,3.594 0.302,0.177 10 false A24 0.135,0.125 1.51,0.427 1.375,0.302 12 false V Bus (for RHD):

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 11 seconds.

·

After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TRANSMISSION CONTROL ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U154770E02
2.063,1.969 1.948,2.51 false 2.167,1.969 2.333,2.521 false 0.115,0.094 0.344,0.271 0.229,0.177 10 false *a 1.656,2.583 2.042,2.76 0.385,0.177 10 false CA1L 2.271,2.573 2.677,2.75 0.406,0.177 10 false CA1H 1.615,0.688 1.875,0.865 0.26,0.177 10 false A24

Disconnect the A24 transmission control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-16 (CA1H) - A24-15 (CA1L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U154769E03
2.198,3.708 2.521,4.125 false 1.208,1.375 0.906,0.948 false 0.115,0.115 0.344,0.292 0.229,0.177 10 false *a 0.5,1.427 0.76,1.604 0.26,0.177 10 false A24 0.521,3.5 0.781,3.677 0.26,0.177 10 false A23 2.552,4.156 2.927,4.333 0.375,0.177 10 false +B 0.677,0.719 0.865,0.896 0.188,0.177 10 false E1

Disconnect the A23 transmission control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-1 (E1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) auxiliary battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A23-16 (+B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)