Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › 2012.03–2014.11
RM2070E _57 Power Source / Network _061936 NETWORKING _0301754 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  U110B  Lost Communication with Parking Assist Control Module "B"  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
U110B No communication from the parking assist ECU continues.
·

Parking assist ECU branch line or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



HINT:

This diagnosis procedure is for when DTC U110B is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C242510E04
0.771,1.688 1.167,1.833 0.396,0.146 10 false 120 Ω 0.313,2.281 0.5,2.427 0.188,0.146 10 false L5 6.229,1.688 6.625,1.833 0.396,0.146 10 false 120 Ω 0.313,2.438 1.615,3.188 1.302,0.75 10 false Power Management Control ECU 3.646,2.76 4.104,2.906 0.458,0.146 10 false CANH 3.448,4.073 4.844,4.448 1.396,0.375 10 false Parking Assist ECU 3.542,4.604 4.448,4.792 0.906,0.188 10 false Trouble Area 3.427,3.813 3.813,3.958 0.385,0.146 10 false ACC 3.427,3.365 3.813,3.51 0.385,0.146 10 false IG 3.146,3.656 3.323,3.802 0.177,0.146 10 false 9 3.521,2.563 3.771,2.708 0.25,0.146 10 false 40 3.063,2.948 3.344,3.094 0.281,0.146 10 false L64 3.063,3.385 3.344,3.531 0.281,0.146 10 false L64 3.063,3.823 3.344,3.969 0.281,0.146 10 false L64 4.844,3.323 5.125,3.469 0.281,0.146 10 false L64 4.156,2.563 4.438,2.708 0.281,0.146 10 false L65 3.76,2.563 4.042,2.708 0.281,0.146 10 false L65 4.5,2.563 4.76,2.708 0.26,0.146 10 false 39 4.906,3.115 5.042,3.26 0.135,0.146 10 false 4 4.354,3.313 4.792,3.458 0.438,0.146 10 false GND1 4.229,2.76 4.688,2.906 0.458,0.146 10 false CANL 1.469,5 3.406,5.177 1.938,0.177 10 false : CAN Main Bus Line (CANH) 1.469,5.396 3.406,5.573 1.938,0.177 10 false : CAN Main Bus Line (CANL) 4.5,5 6.229,5.177 1.729,0.177 10 false : CAN Branch Line (CANH) 4.5,5.396 6.208,5.573 1.708,0.177 10 false : CAN Branch Line (CANL) 3.146,3.208 3.323,3.354 0.177,0.146 10 false 8 5.708,2.281 6.99,2.802 1.281,0.521 10 false CAN No. 4 Junction Connector 2.229,3.563 3.156,3.74 0.927,0.177 10 false ECU-IG NO. 2 2.24,3.948 2.99,4.198 0.75,0.25 10 false ECU-ACC 2.25,3.073 3,3.323 0.75,0.25 10 false RAD NO. 1 3.406,2.917 3.813,3.26 0.406,0.344 10 false +B 3.146,2.76 3.281,2.906 0.135,0.146 10 false 1 0.146,0.104 2.208,0.688 2.063,0.583 12 false Sub Bus 11:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.


Result:
Result Proceed to
U1002 is not output from power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from power management control ECU (GTS display: PM1 Gateway) B




A

2.CHECK FOR OPEN IN CAN BUS LINES (PARKING ASSIST ECU BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (PARKING ASSIST ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
U191299E01
2.168,0.214 2.432,0.395 0.264,0.181 10 L65 0.123,0.097 0.288,0.244 0.165,0.147 10 *a 2.882,0.642 3.313,0.788 0.431,0.147 10 CANH 1.848,1.881 2.305,2.028 0.457,0.147 10 CANL 2.345,1.97 2.422,1.97 2.422,1.97 2.599,1.469 false 2.858,0.74 2.803,0.74 2.803,0.74 2.721,1.406 false

Disconnect the parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L65-40 (CANH) - L65-39 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (PARKING ASSIST ECU)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
U190999E01
1.521,2.86 1.858,3.016 0.336,0.156 10 ACC 0.272,0.754 0.498,0.910 0.225,0.156 10 +B 0.092,0.054 0.318,0.210 0.225,0.156 10 *a 2.784,0.864 3.211,1.020 0.427,0.156 10 GND1 1.532,1.175 1.848,1.331 0.316,0.156 10 L64 2.759,0.945 2.694,0.945 2.694,0.945 2.638,1.902 false 0.53,0.84 0.613,0.84 0.613,0.84 0.854,1.902 false 1.34,2.285 1.21,2.837 false 1.089,2.868 1.264,3.024 0.174,0.156 10 IG 1.49,2.288 1.673,2.835 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L64-4 (GND1) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Parking Assist ECU)


b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L64-1 (+B) - Body ground Power switch off 11 to 14 V
L64-9 (ACC) - Body ground Power switch on (ACC) 11 to 14 V
L64-8 (IG) - Body ground Power switch on (IG) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)