Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301758 WIRELESS DOOR LOCK CONTROL SYSTEM U

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


a.

Disconnect the MB and L8*1 main body ECU (multiplex network body ECU) connector.

U191253E02
1.771,0.573 1.625,0.573 1.625,0.573 1.625,0.854 false 1.552,1.406 1.458,1.406 1.458,1.406 1.458,3.167 false 0.677,2.677 1.021,2.677 false 3.406,7.885 3.667,8.042 0.26,0.156 10 false MB 5.031,6.625 5.292,6.781 0.26,0.156 10 false 2A 1.781,6.583 2.042,6.74 0.26,0.156 10 false 2B 5.063,5.25 5.323,5.406 0.26,0.156 10 false 2C 1.792,5.281 2.052,5.438 0.26,0.156 10 false 2D 4.688,3.969 4.948,4.125 0.26,0.156 10 false 2E 4.979,3.969 5.24,4.125 0.26,0.156 10 false *B 5.656,3.979 5.917,4.135 0.26,0.156 10 false *C 5.354,3.969 5.615,4.125 0.26,0.156 10 false 2F 1.813,3.938 2.073,4.094 0.26,0.156 10 false L7 0.219,2.448 0.479,2.604 0.26,0.156 10 false 2E 0.521,2.448 0.781,2.604 0.26,0.156 10 false *B 0.521,2.74 0.781,2.896 0.26,0.156 10 false *C 0.229,2.74 0.49,2.896 0.26,0.156 10 false 2F 0.417,1.302 0.677,1.458 0.26,0.156 10 false 2D 0.417,2.052 0.677,2.208 0.26,0.156 10 false 2C 1.938,1.438 2.198,1.594 0.26,0.156 10 false L7 1.823,0.5 1.979,0.656 0.156,0.156 10 false *1 3.698,0.552 3.958,0.708 0.26,0.156 10 false MB 6.333,2.083 6.594,2.24 0.26,0.156 10 false 2A 6.323,1.406 6.583,1.563 0.26,0.156 10 false 2B 0.365,0.104 0.625,0.302 0.26,0.198 10 false *A 1.385,3.198 1.542,3.354 0.156,0.156 10 false *2

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 1 connector *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 1 connector

U190870E02
1.781,0.677 1.625,0.677 1.625,0.677 1.625,0.958 false 1.542,1.406 1.458,1.406 1.458,1.406 1.458,3.281 false 1.552,1.698 1.469,1.698 false 1.552,2.052 1.469,2.052 false 0.708,2.781 1.031,2.781 false 3.156,7.594 3.448,7.76 0.292,0.167 10 false MB 4.875,6.385 5.167,6.552 0.292,0.167 10 false 2A 1.885,6.385 2.177,6.552 0.292,0.167 10 false 2B 1.167,5.115 1.458,5.281 0.292,0.167 10 false 2D 0.531,1.5 0.823,1.667 0.292,0.167 10 false 2D 3.927,5.135 4.219,5.302 0.292,0.167 10 false 2C 0.521,2.167 0.813,2.333 0.292,0.167 10 false 2C 4.875,3.802 5.167,3.969 0.292,0.167 10 false L7 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.594,5.115 5.885,5.281 0.292,0.167 10 false 2E 5.875,5.115 6.083,5.281 0.208,0.167 10 false *B 6.552,5.115 6.76,5.281 0.208,0.167 10 false *C 2.438,3.813 2.729,3.979 0.292,0.167 10 false L8 0.271,2.563 0.563,2.729 0.292,0.167 10 false 2E 0.552,2.583 0.844,2.75 0.292,0.167 10 false *B 0.563,2.854 0.854,3.021 0.292,0.167 10 false *C 0.271,2.854 0.563,3.021 0.292,0.167 10 false 2F 2.01,1.698 2.302,1.865 0.292,0.167 10 false L7 2.01,2.063 2.302,2.229 0.292,0.167 10 false L8 6.271,1.542 6.479,1.708 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.271,2.198 6.479,2.365 0.208,0.167 10 false 2A 1.823,0.583 1.979,0.74 0.156,0.156 10 false *1 0.375,0.198 0.635,0.396 0.26,0.198 10 false *A 1.365,3.313 1.521,3.469 0.156,0.156 10 false *2

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Tester Connection Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
L8-3 (GND2) - Body ground*1 W-B - Body ground Ground Always Below 1 Ω
MB-30 (BECU) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch on (ACC) 11 to 14 V
MB-29 (ACC) - Body ground - ACC power supply Power switch off Below 1 V
MB-31 (ALTB) - Body ground - Auxiliary battery power supply Power switch off 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch on (IG) 11 to 14 V
MB-32 (IG) - Body ground - Power switch power supply Power switch off Below 1 V

If the result is not as specified, there may be a malfunction in the wire harness.


c.

Reconnect the MB and L8*1 main body ECU (multiplex network body ECU) connector.


d.

Measure the voltage according to the value(s) in the table below.

Tester Connection Wiring Color Terminal Description Condition Specified Condition
2B-1 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-1 (ACT-) - Body ground B - Body ground Door lock motor unlock drive output (except driver door) Door control switch (multiplex network master switch) or driver door key cylinder unlocked 11 to 14 V
2B-8 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder off Below 1 V
2B-8 (ACT+) - Body ground L - Body ground Door lock motor lock drive output (all doors) Door control switch (multiplex network master switch) or driver door key cylinder locked 11 to 14 V
2D-35 (FLCY) - Body ground Y - Body ground*2
V - Body ground*3
Front door LH courtesy light switch input Front door LH open Below 1 V
2D-35 (FLCY) - Body ground Y - Body ground*2
V - Body ground*3
Front door LH courtesy light switch input Front door LH closed 11 to 14 V
2D-36 (FRCY) - Body ground BR - Body ground*2
V - Body ground*3
Front door RH courtesy light switch input Front door RH open Below 1 V
2D-36 (FRCY) - Body ground BR - Body ground*2
V - Body ground*3
Front door RH courtesy light switch input Front door RH closed 11 to 14 V
L7-6 (LRCY) - Body ground G - Body ground Rear door courtesy light switch input Rear door LH or RH open Below 1 V
L7-6 (LRCY) - Body ground G - Body ground Rear door courtesy light switch input Rear door LH and RH closed Pulse generation
L7-7 (LSFL) - Body ground GR - Body ground Front door LH unlock detection switch input Front door LH unlocked Below 1 V
L7-7 (LSFL) - Body ground GR - Body ground Front door LH unlock detection switch input Power switch off, all doors closed and front door LH locked Pulse generation
L7-18 (LSFR) - Body ground LG - Body ground Front door RH unlock detection switch input Front door RH unlocked Below 1 V
L7-18 (LSFR) - Body ground LG - Body ground Front door RH unlock detection switch input Power switch off, all doors closed and front door RH locked Pulse generation
2B-29 (LSR) - Body ground GR - Body ground Rear door RH unlock detection switch input Rear door RH or LH unlocked Below 1 V
2B-29 (LSR) - Body ground GR - Body ground Rear door RH unlock detection switch input Power switch off, all doors closed, rear door RH and LH locked Pulse generation
2D-25 (LSR) - Body ground GR - Body ground Rear door LH unlock detection switch input Rear door LH or RH unlocked Below 1 V
2D-25 (LSR) - Body ground GR - Body ground Rear door LH unlock detection switch input Power switch off, all doors closed, rear door LH and RH locked Pulse generation
2C-23 (BZR) - Body ground R - Body ground Wireless door lock buzzer signal Wireless door lock buzzer off Below 1 V
2C-23 (BZR) - Body ground R - Body ground Wireless door lock buzzer signal Wireless door lock buzzer on 11 to 14 V

·

*1: Main body ECU (Multiplex Network Body ECU) with 3 connectors

·

*2: for LHD

·

*3: for RHD


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U154541E03
2.469,0.542 2.813,0.802 0.344,0.26 10 false L62 4.698,0.542 5.052,0.823 0.354,0.281 10 false L63

a.

Disconnect the L62 and L63 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L62-15 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω
L62-1 (+B) - L62-15 (E) B - W-B Auxiliary battery power supply Power switch off 11 to 14 V

If the result is not as specified, there may be a malfunction in the wire harness.



c.

Reconnect the L62 and L63 certification ECU (smart key ECU assembly) connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L62-16 (IG) - L62-15 (E) BE - W-B IG power supply Power switch on (IG) 11 to 14 V
Power switch off Below 1 V
L63-16 (RSSI) - L62-15 (E) SB - W-B Door control receiver output signal Power switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed 11 to 14 V or pulse generation
Power switch off, all doors closed and electrical key transmitter sub-assembly switch pressed Below 2 V
L63-15 (RDA) - L62-15 (E) Y - W-B Door control receiver data input signal Power switch off, all doors closed and electrical key transmitter sub-assembly switch not pressed 11 to 14 V or pulse generation
Power switch off, all doors closed and electrical key transmitter sub-assembly switch pressed Pulse generation
L63-5 (RCO) - L62-15 (E) LG - W-B Supply battery to door control receiver Power switch off, all doors closed and electrical key transmitter sub-assembly switch pressed 4.5 to 5.5 V

If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.