Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301758 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive electrical waves relating to the entry functions of the entry and start system. The certification ECU (smart key ECU assembly) decodes the requested entry and start system operation by identifying a key code based on the electric waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. DTC Detection Condition Trouble Area
B1242
·

Short in RDA or RSSI to ground between the certification ECU (smart key ECU assembly) and the door control receiver.

·

Short in RDA or RSSI to ground when RCO (5 V) output from the ECU is off.


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (Smart key ECU assembly)



WIRING DIAGRAM

B282114E06
0.38,4.224 1.814,4.379 1.434,0.155 10 Door Control Receiver 5.56,4.024 7.105,4.328 1.545,0.304 10 Certification ECU (Smart Key ECU Assembly) 1.196,1.096 1.578,1.238 0.382,0.142 10 RSSI 1.188,1.891 1.578,2.037 0.390,0.145 10 DATA 1.394,2.672 1.580,2.828 0.186,0.156 10 +5 5.463,1.103 5.721,1.246 0.258,0.142 10 L63 5.463,1.874 5.721,2.016 0.258,0.142 10 L63 5.463,2.686 5.721,2.829 0.258,0.142 10 L63 5.463,3.513 5.721,3.655 0.258,0.142 10 L62 5.828,1.089 6.208,1.232 0.380,0.142 10 RSSI 5.828,1.882 6.159,2.023 0.332,0.141 10 RDA 5.828,2.683 6.187,2.839 0.360,0.156 10 RCO 1.705,0.982 1.800,1.121 0.096,0.139 10 2 1.705,1.771 1.799,1.908 0.095,0.137 10 5 1.705,2.567 1.801,2.703 0.096,0.136 10 4 5.505,3.309 5.679,3.450 0.174,0.141 10 15 5.544,2.468 5.640,2.605 0.096,0.137 10 5 5.506,1.652 5.678,1.790 0.172,0.138 10 15 5.828,3.533 5.981,3.689 0.153,0.156 10 E 5.498,0.862 5.677,1.000 0.179,0.139 10 16 0.38,4.045 0.654,4.201 0.274,0.156 10 S12 1.249,3.485 1.578,3.641 0.330,0.156 10 GND 1.705,3.393 1.799,3.530 0.095,0.136 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

·

Before performing the inspection, check that there are no problems related to the CAN communication system.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the certification ECU (smart key ECU assembly) connectors.


b.

Disconnect the door control receiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L63-16 (RSSI) - S12-2 (RSSI) Always Below 1 Ω
L63-15 (RDA) - S12-5 (DATA) Always Below 1 Ω
L63-5 (RCO) - S12-4 (+5) Always Below 1 Ω
L62-15 (E) - Body ground Always Below 1 Ω
S12-1 (GND) - Body ground Always Below 1 Ω
L63-16 (RSSI) or S12-2 (RSSI) - Body ground Always 10 kΩ or higher
L63-15 (RDA) or S12-5 (DATA) - Body ground Always 10 kΩ or higher
L63-5 (RCO) or S12-4 (+5) - Body ground Always 10 kΩ or higher




OK

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
U154542E01
0.057,0.044 0.208,0.183 0.151,0.139 10 *a 0.959,0.298 1.216,0.438 0.258,0.140 10 L62 0.348,1.582 0.458,1.724 0.110,0.142 10 E 2.767,1.582 3.100,1.722 0.333,0.140 10 RCO 2.397,0.298 2.650,0.438 0.253,0.140 10 L63 2.758,0.93 2.948,1.549 false 0.408,0.925 0.408,1.557 false

Reconnect the certification ECU (smart key ECU assembly) connectors.


b.

Reconnect the door control receiver connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L63-5 (RCO) - L62-15 (E) Power switch off, all doors closed and electrical key transmitter sub- assembly switch pressed 4.5 to 5.5 V


Text in Illustration
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))



OK

3.REPLACE DOOR CONTROL RECEIVER

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

3.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new one (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER(w/o Tire Pressure Warning System)>REMOVAL).



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

b.

Recheck for DTCs.

OK:

DTC B1242 is not output.




OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)