Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301758 WIRELESS DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver is used to receive electrical waves relating to the entry functions of the entry and start system. The certification ECU (smart key ECU assembly) decodes the requested entry and start system operation by identifying a key code based on the electric waves received via the door control receiver. The door control receiver receives a signal from the electrical key transmitter sub-assembly and sends signals to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly). The certification ECU (smart key ECU assembly) then sends a command, according to the requested operation, to each ECU (ex. if door lock operation is requested, the certification ECU (smart key ECU assembly) sends a door lock command to the main body ECU (multiplex network body ECU)).

DTC No. DTC Detection Condition Trouble Area
B1242
·

Short in RDAM to ground between the certification ECU (smart key ECU assembly) and the door control receiver.

·

Short in RDAM to ground when RCO (5 V) output from the ECU is off.


·

Wire harness or connector

·

Door control receiver

·

Certification ECU (Smart key ECU assembly)



WIRING DIAGRAM

B440789E87
1.177,0.865 1.792,1.063 0.615,0.198 10 false DATA 1.365,1.667 1.979,1.865 0.615,0.198 10 false +5 1.26,2.365 1.875,2.563 0.615,0.198 10 false GND 1.646,0.76 2.26,0.958 0.615,0.198 10 false 9 1.635,2.24 2.25,2.438 0.615,0.198 10 false 12 1.635,1.552 2.25,1.75 0.615,0.198 10 false 10 0.396,2.844 1.01,3.042 0.615,0.198 10 false R42 0.396,3.01 3.031,3.385 2.635,0.375 10 false Electrical Key and Tire Pressure Monitoring System Receiver Assembly 5.479,2.854 7.031,3.292 1.552,0.438 10 false Certification ECU (Smart Key ECU Assembly) 5.74,0.865 6.354,1.063 0.615,0.198 10 false RDAM 5.75,2.344 6.365,2.542 0.615,0.198 10 false E 5.74,1.667 6.354,1.865 0.615,0.198 10 false RCO 5.344,0.844 5.958,1.042 0.615,0.198 10 false L196 5.354,1.646 5.969,1.844 0.615,0.198 10 false L196 5.354,2.333 5.969,2.531 0.615,0.198 10 false L195 5.406,0.646 6.021,0.844 0.615,0.198 10 false 17 5.438,1.448 6.052,1.646 0.615,0.198 10 false 5 5.396,2.135 6.01,2.333 0.615,0.198 10 false 11 0.104,0.104 2.552,0.302 2.448,0.198 12 false for 12 Pin Type:

B440789E88
1.177,0.865 1.792,1.063 0.615,0.198 10 false DATA 1.365,1.667 1.979,1.865 0.615,0.198 10 false +5 1.26,2.365 1.875,2.563 0.615,0.198 10 false GND 1.646,0.76 2.26,0.958 0.615,0.198 10 false 5 1.635,2.24 2.25,2.438 0.615,0.198 10 false 1 1.635,1.552 2.25,1.75 0.615,0.198 10 false 4 0.396,2.844 1.01,3.042 0.615,0.198 10 false S12 0.396,3.01 1.896,3.188 1.5,0.177 10 false Door Control Receirver 5.479,2.854 7.031,3.292 1.552,0.438 10 false Certification ECU (Smart Key ECU Assembly) 5.74,0.865 6.354,1.063 0.615,0.198 10 false RDAM 5.75,2.344 6.365,2.542 0.615,0.198 10 false E 5.74,1.667 6.354,1.865 0.615,0.198 10 false RCO 5.344,0.844 5.958,1.042 0.615,0.198 10 false L196 5.354,1.646 5.969,1.844 0.615,0.198 10 false L196 5.354,2.333 5.969,2.531 0.615,0.198 10 false L195 5.406,0.646 6.021,0.844 0.615,0.198 10 false 17 5.438,1.448 6.052,1.646 0.615,0.198 10 false 5 5.396,2.135 6.01,2.333 0.615,0.198 10 false 11 0.104,0.104 2.552,0.302 2.448,0.198 12 false for 5 Pin Type:

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, entry and wireless function performance may be affected.

·

Before performing the inspection, check that there are no problems related to the CAN communication system.

·

When replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

This DTC is not detected within 10 seconds after the power switch turned to off from on (IG).

·

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal. (See pageSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION)*

·

It is necessary to perform initialization (See pageSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See pageSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the door control receiver if the door control receiver has been replaced.*


*: for 12 Pin Type



PROCEDURE

1.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the R42*1 or S12*2 door control receiver connector.

*1: for 12 Pin Type

*2: for 5 Pin Type


U190971E02
4.271,0.979 4.063,1.479 true 4.052,1.656 4.281,2.313 true 2.521,1.646 2.75,2.302 true 3.281,0.51 3.75,0.75 0.469,0.24 10 false L196 1.896,0.51 2.292,0.781 0.396,0.271 10 false L195 4.823,0.51 5.385,0.688 0.563,0.177 10 false L197 4.177,0.802 4.656,0.979 0.479,0.177 10 false RCO 4.167,2.333 4.833,2.51 0.667,0.177 10 false RDAM 2.719,2.323 3.385,2.5 0.667,0.177 10 false E 0.146,0.115 0.813,0.292 0.667,0.177 10 false *a

Text in Illustration
*a Component with harness connected (Certification ECU (Smart Key ECU Assembly)) - -


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L196-5 (RCO) - L195-11 (E) Always Below 1 V → 4.5 to 5.5 V (Pulse generation)
L196-17 (RDAM) - L195-11 (E) Always 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
L195-11 (E) - Body ground Always Below 1 Ω


Result:
Result Proceed to
OK (For 12 Pin Type) A
OK (For 5 Pin Type) B
NG C




A

REPLACE ELECTRICAL KEY AND TIRE PRESSURE MONITORING SYSTEM RECEIVER ASSEMBLY

B

C

2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the L196 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L196-17 (RDAM) - R42-9 (DATA)*1
L196-17 (RDAM) - S12-5 (DATA)*2
Always Below 1 Ω
L196-5 (RCO) - R42-10 (+5)*1
L196-5 (RCO) - S12-4 (+5)*2
Always Below 1 Ω
R42-12 (GND) - Body ground*1
S12-1 (GND) - Body ground*2
Always Below 1 Ω
L196-17 (RDAM) or R42-9 (DATA) - Body ground*1
L196-17 (RDAM) or S12-5 (DATA) - Body ground*2
Always 10 kΩ or higher
L196-5 (RCO) or R42-10 (+5) - Body ground*1
L196-5 (RCO) or S12-4 (+5) - Body ground*2
Always 10 kΩ or higher



*1: for 12 Pin Type

*2: for 5 Pin Type



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR