Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2014.11
RM2070E _58 Vehicle Interior _061937 DOOR LOCK _0301762 REAR DOOR LOCK G

DOOR LOCK  REAR DOOR LOCK  INSPECTION  


PROCEDURE

Hide 69060A 1.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/o Double Locking System)

a.
B340417E03
1.979,3.823 1.979,4.219 1.979,4.219 2.219,4.219 false 1.469,3.865 1.469,4.219 1.469,4.219 1.229,4.219 false 2.552,3.604 2.146,3.604 false 1.26,3.604 0.844,3.604 false 1.094,4.125 1.271,4.354 0.177,0.229 10 false E 2.302,4.135 2.802,4.385 0.5,0.25 10 false LSSR 2.604,3.521 2.833,3.75 0.229,0.229 10 false UL 0.698,3.5 0.875,3.729 0.177,0.229 10 false L 1.656,2.313 1.833,2.542 0.177,0.229 10 false *b 0.885,2.823 1.063,3.052 0.177,0.229 10 false *c 2.063,2.125 2.24,2.354 0.177,0.229 10 false *a

Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Auxiliary battery positive (+) → Terminal 4 (L)
Auxiliary battery negative (-) → Terminal 1 (UL)
Locks
Auxiliary battery positive (+) → Terminal 1 (UL)
Auxiliary battery negative (-) → Terminal 4 (L)
Unlocks


Text in Illustration
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock with Motor Assembly LH)

If the result is not as specified, replace the rear door lock with motor assembly LH.



b.

Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69060A 2.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY LH (w/ Double Locking System)

a.
B164419E12
0.119,0.097 0.268,0.239 0.149,0.142 10 *a 2.282,4.072 2.434,4.214 0.152,0.142 10 *b 1.655,4.072 1.811,4.211 0.156,0.140 10 *c 1.117,3.894 1.117,1.911 1.117,1.911 0.664,1.911 false 0.679,3.895 0.679,2.639 0.679,2.639 0.54,2.639 false 0.902,3.895 0.902,2.304 0.902,2.304 0.665,2.304 false 0.455,3.895 0.455,3.169 0.455,3.169 0.375,3.169 false 0.406,1.823 0.605,1.962 0.198,0.139 10 UL 0.542,2.22 0.637,2.359 0.095,0.139 10 L 0.063,2.562 0.459,2.701 0.396,0.139 10 UNDL 0.138,3.084 0.336,3.223 0.198,0.139 10 DL

Check the operation of the door lock motor and double lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor and double lock motor.

OK:
Connection Result
Auxiliary battery positive (+) → 2 (L)
Auxiliary battery negative (-) → 1 (UL)
Locks
Auxiliary battery positive (+) → 1 (UL)
Auxiliary battery negative (-) → 2 (L)
Unlocks
Auxiliary battery positive (+) → 4 (DL)
Auxiliary battery negative (-) → 3 (UNDL)
Sets
Auxiliary battery positive (+) → 3 (UNDL)
Auxiliary battery negative (-) → 4 (DL)
Unsets


Text in Illustration
*a Component without harness connected
(Rear door lock with motor assembly LH)
*b Unlock
*c Lock

HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock with motor assembly LH.



b.
B273308E02
0.119,0.103 0.268,0.245 0.149,0.142 10 *a 2.279,3.493 2.431,3.635 0.152,0.142 10 *b 1.663,3.493 1.819,3.633 0.156,0.140 10 *c 1.171,3.612 1.171,4.049 1.171,4.049 1.961,4.049 false 1.033,3.612 1.033,4.309 1.033,4.309 1.978,4.309 false 0.569,3.612 0.569,4.556 0.569,4.556 1.663,4.556 false 0.397,3.612 0.397,4.312 0.397,4.312 0.303,4.312 false 0.177,4.233 0.287,4.371 0.111,0.137 10 E 1.686,4.488 2.077,4.626 0.391,0.137 10 DLSR 1.984,3.967 2.365,4.107 0.380,0.140 10 LSSR 1.984,4.228 2.095,4.365 0.111,0.137 10 E

Check the operation of the unlock detection switch and double lock position switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (LSSR) - 6 (E) Locked 10 kΩ or higher
5 (LSSR) - 6 (E) Unlocked Below 1 Ω
9 (DLSR) - 10 (E) Unset 10 kΩ or higher
9 (DLSR) - 10 (E) Set Below 1 Ω


Text in Illustration
*a Component without harness connected
(Rear door lock with motor assembly LH)
*b Unlock
*c Lock

If the result is not as specified, replace the rear door lock with motor assembly LH.



Hide 69050A 3.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/o Double Locking System)

a.
B340416E03
1.979,3.854 1.979,4.26 1.979,4.26 2.333,4.26 false 1.469,3.854 1.469,4.26 1.469,4.26 1.115,4.26 false 2.625,3.594 2.156,3.594 false 1.281,3.594 0.813,3.594 false 2.688,3.5 3.073,3.698 0.385,0.198 10 false UL 2.385,4.177 2.771,4.375 0.385,0.198 10 false LSSR 0.938,4.177 1.323,4.375 0.385,0.198 10 false E 0.646,3.49 1.031,3.688 0.385,0.198 10 false L 0.781,2.698 1.167,2.896 0.385,0.198 10 false *c 1.563,2.313 1.948,2.51 0.385,0.198 10 false *b 1.021,2.063 1.406,2.26 0.385,0.198 10 false *a

Check the operation of the door lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor.

OK:
Connection Result
Auxiliary battery positive (+) → Terminal 4 (L)
Auxiliary battery negative (-) → Terminal 1 (UL)
Locks
Auxiliary battery positive (+) → Terminal 1 (UL)
Auxiliary battery negative (-) → Terminal 4 (L)
Unlocks


Text in Illustration
*a Unlock
*b Lock
*c Component without harness connected
(Rear Door Lock with Motor Assembly RH)

If the result is not as specified, replace the rear door lock with motor assembly RH.



b.

Check the operation of the unlock detection switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (LSSR) - 9 (E) Locked 10 kΩ or higher
6 (LSSR) - 9 (E) Unlocked Below 1 Ω


If the result is not as specified, replace the rear door lock with motor assembly RH.



Hide 69050A 4.INSPECT REAR DOOR LOCK WITH MOTOR ASSEMBLY RH (w/ Double Locking System)

a.
B164420E11
2.039,4.069 2.187,4.207 0.149,0.139 10 *b 2.639,4.069 2.789,4.207 0.150,0.139 10 *c 0.139,0.111 0.295,0.258 0.156,0.147 10 *a 0.847,3.913 0.847,2.446 0.847,2.446 0.918,2.446 false 0.623,3.913 0.623,2.033 0.623,2.033 0.824,2.033 false 0.4,3.913 0.4,1.63 0.4,1.63 0.6,1.63 false 0.625,1.535 0.722,1.680 0.097,0.145 10 L 0.87,1.96 1.074,2.106 0.205,0.145 10 UL 1.437,3.904 1.839,4.050 0.402,0.145 10 UNDL 0.939,2.369 1.143,2.514 0.205,0.145 10 DL 1.132,3.976 1.422,3.976 false

Check the operation of the door lock motor and double lock motor.

i.

Apply auxiliary battery voltage and check the operation of the door lock motor and double lock motor.

OK:
Connection Result
Auxiliary battery positive (+) → 4 (L)
Auxiliary battery negative (-) → 3 (UL)
Locks
Auxiliary battery positive (+) → 3 (UL)
Auxiliary battery negative (-) → 4 (L)
Unlocks
Auxiliary battery positive (+) → 2 (DL)
Auxiliary battery negative (-) → 1 (UNDL)
Sets
Auxiliary battery positive (+) → 1 (UNDL)
Auxiliary battery negative (-) → 2 (DL)
Unsets


Text in Illustration
*a Component without harness connected
(Rear door lock with motor assembly RH)
*b Unlock
*c Lock

HINT:
·

Move the door lock motor to the lock position and set the double locking system. Check that the doors cannot be unlocked by operating the control cable.

·

Move the door lock motor to the lock position and unset the double locking system. Check that the doors can be unlocked by operating the control cable.



If the result is not as specified, replace the rear door lock with motor assembly RH.



b.

Check the operation of the unlock detection switch and double lock position switch.

i.
B273310E01
0.096,0.058 0.275,0.223 0.179,0.165 10 *a 2.626,3.447 2.805,3.612 0.179,0.165 10 *c 1.961,3.447 2.140,3.612 0.179,0.165 10 *b 1.112,3.584 1.112,3.943 1.112,3.943 1.468,3.943 false 0.967,3.582 0.967,4.163 0.967,4.163 1.47,4.163 false 0.503,3.582 0.503,4.352 0.503,4.352 1.47,4.352 false 0.348,3.582 0.348,4.55 0.348,4.55 1.47,4.55 false 1.509,4.263 1.907,4.417 0.399,0.154 10 LSSR 1.509,4.47 1.618,4.623 0.110,0.154 10 E 1.509,4.08 1.625,4.234 0.117,0.154 10 E 1.509,3.865 1.907,4.019 0.399,0.154 10 DLSR

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (LSSR) - 10 (E) Locked 10 kΩ or higher
9 (LSSR) - 10 (E) Unlocked Below 1 Ω
5 (DLSR) - 6 (E) Unset 10 kΩ or higher
5 (DLSR) - 6 (E) Set Below 1 Ω


Text in Illustration
*a Component without harness connected
(Rear door lock with motor assembly RH)
*b Unlock
*c Lock

If the result is not as specified, replace the rear door lock with motor assembly RH.