Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2012.03–2016.05
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301767 ENTRY AND START SYSTEM(for Entry Function) U

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  TERMINALS OF ECU  


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U154538E03
2.479,0.552 2.76,0.729 0.281,0.177 10 false L62 4.719,0.552 5,0.729 0.281,0.177 10 false L63

a.

Disconnect the L62 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
L62-15 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
L62-1 (+B) - L62-15 (E) Input B - W-B +B power supply Power switch off 11 to 14 V -
L62-17 (CUTB) - L62-15 (E) Input R - W-B Dark current cut pin* Power switch off 11 to 14 V -

*: In order to prevent the auxiliary battery from being depleted when the vehicle is shipped long distances, a fuse that cuts unnecessary electrical load while the vehicle is being shipped is set in the circuit. If the fuse is removed, the circuit becomes open. If the fuse that is between the auxiliary battery and terminal CUTB is removed and the circuit is open, the certification ECU (smart key ECU assembly) changes to a certain control mode (example: the transmission of electric waves every 250 ms. that form the detection area stops).


If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.


c.

Reconnect the L62 certification ECU (smart key ECU assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
L62-16 (IG) - L62-15 (E) Input BE - W-B IG power supply Power switch off → on (IG) Below 1 V → 11 to 14 V Power Switch
L62-3 (CLG1) - L62-15 (E) Output L - W-B Output to driver door electrical key antenna
[request signal (challenge) is sent to door electrical key oscillator from certification ECU (smart key ECU assembly) to form detection area]
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Driver Side (key diagnostic mode)
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
L62-4 (CG1B) - L62-15 (E) Output Y - W-B Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*2

6.

All doors locked with key


Pulse generation (See waveform 2) Over Head + Driver Side (key diagnostic mode)
L62-5 (CLG2) - L62-15 (E)*4 Output G - W-B Output to front passenger door electrical key antenna Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought inside detection area*1

6.

All doors locked through wireless operation


Pulse generation (See waveform 1) Over Head + Passenger Side (key diagnostic mode)
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*2

6.

All doors locked through wireless operation


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
L62-6 (CG2B) - L62-15 (E)*4 Output R - W-B Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*2

6.

All doors locked with key


Pulse generation (See waveform 2) Over Head + Passenger Side (key diagnostic mode)
L62-7 (CLG5) - L62-15 (E) Output V - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) Procedure:
1.

Power switch off

2.

Key not in side vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
L62-8 (CG5B) - L62-15 (E) Output L - W-B Output to No. 1 indoor electrical key antenna assembly (front floor) (terminal on opposite side of component from CLG5 output terminal) Procedure:
1.

Power switch off

2.

Key not in side vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


Pulse generation (See waveform 3) Over Head + Front Room (key diagnostic mode)
L62-18 (TSW1) - L62-15 (E) Input G - W-B Driver door lock sensor signal input
(Sends signal from door lock switch in front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock switch is touched, the pulse is grounded.
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched


Pulse generation (See waveform 5) D-Door Trigger Switch
L62-19 (TSW2) - L62-15 (E)*4 Input W - W-B Front passenger door lock sensor signal input
(Sends signal from door lock switch in front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock switch is touched, the pulse is grounded.
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched


Pulse generation (See waveform 5) P-Door Trigger Switch
L62-20 (SEN1) - L62-15 (E) Input V - W-B Driver door unlock sensor signal input
[when system is in unlock standby mode and touch sensor is touched, door electrical key oscillator sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)]
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched


Pulse generation (See waveform 5) D-Door Touch Sensor
L62-21 (SEN2) - L62-15 (E)*4 Input Y - W-B Front passenger door unlock sensor signal input
[when system is in unlock standby mode and touch sensor is touched, door electrical key oscillator sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly)]
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched


Pulse generation (See waveform 5) P-Door Touch Sensor
L62-22 (TSW5) - Body ground*4 Input GR - Body ground Back door unlock switch signal input Back door opener switch (back door unlock switch) off → on Pulse generation (See waveform 5) Tr/B-Door Unlock SW
L62-23 (TSW6) - Body ground*4 Input B - Body ground Back door lock switch signal input Back door opener switch (back door lock switch) off → on Pulse generation (See waveform 5) Tr/B-Door Lock SW
L62-24 (CLG6) - L62-15 (E) Output P - W-B Output to No. 3 indoor electrical key antenna assembly (rear floor) Procedure:
1.

Power switch off

2.

Key not in side vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
L62-25 (CG6B) - L62-15 (E) Output BR - W-B Output to No. 3 indoor electrical key antenna assembly (rear floor) Proceed:
1.

Power switch off

2.

Key not in side vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


Pulse generation (See waveform 3) Over Head + Rear Room (key diagnostic mode)
L62-26 (CLG7) - L62-15 (E) Output V - W-B Output to No. 2 indoor electrical key antenna assembly (inside luggage) Proceed:
1.

Power switch off

2.

Key not in side vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


Pulse generation (See waveform 3) Over Head + Back Door (inside) (key diagnostic mode)
L62-27 (CG7B) - L62-15 (E) Output R - W-B Output to No. 2 indoor electrical key antenna assembly (inside luggage) Proceed:
1.

Power switch off

2.

Key not in side vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse


Pulse generation (See waveform 3) Over Head + Back Door (inside) (key diagnostic mode)
L62-32 (POS1) - L62-15 (E) Output GR - W-B Driver door unlock sensor power source (12 V (drops when power switch turned on (IG))) Power switch off → on (IG) 9 to 14 V → Below 2 V -
L62-33 (POS2) - L62-15 (E)*4 Output SB - W-B Front passenger door unlock sensor power source (12 V (drops when power switch turned on (IG))) Power switch off → on (IG) 9 to 14 V → Below 2 V -
L63-5 (RCO) - L62-15 (E) Output LG - W-B Output to door control receiver
(Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

Key brought outside detection area*2 but kept inside wireless function operational area*3

4.

Lock or unlock button of key not pressed → pressed


Pulse generation (See waveform 6) -
L63-15 (RDA) - L62-15 (E) Input Y - W-B Door control receiver verifies data received from key. Receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly). Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key brought outside detection area*2 but kept inside wireless function operational area*3

5.

Lock or unlock button of key not pressed → pressed


Pulse generation (See waveform 7) -
L63-16 (RSSI) - L62-15 (E) Input SB - W-B Door control receiver sends signal to certification ECU (smart key ECU assembly) indicating whether electric waves (example: 312 MHz) from key are being received or not (receiver grounds 12 V signal from certification ECU (smart key ECU assembly)) Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key brought outside detection area*2 but kept inside wireless function operational area*3

5.

Lock or unlock button of key not pressed → pressed


Pulse generation (See waveform 8) -
L63-19 (CLG8) - L62-15 (E)*4 Output G - W-B Output to electrical key antenna (outside luggage) Procedure:
1.

Power switch off

2.

All doors closed

3.

Back door opener switch (back door lock switch) off → on


Pulse generation (See waveform 4) Over Head + Back Door (key diagnostic mode)
L63-20 (CG8B) - L62-15 (E)*4 Output P - W-B Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal) Procedure:
1.

Power switch off

2.

All doors closed

3.

Back door opener switch (back door lock switch) off → on


Pulse generation (See waveform 4) Over Head + Back Door (key diagnostic mode)

*1: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

*4: Except Driver's Door Only Entry and Start System



e.
B251021E22
0.177,1.01 0.51,1.208 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Terminal No. (Symbol)
·

L62-3 (CLG1) - L62-15 (E)

·

L62-5 (CLG2) - L62-15 (E)*1


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought inside detection area*2

6.

All doors locked through wireless operation



·

*1: Except Driver's Door Only Entry and Start System

·

*2: For details about the areas that are inside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



f.
B251024E04
0.177,1.052 0.844,1.458 0.667,0.406 10 false GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Terminal No. (Symbol)
·

L62-3 (CLG1) - L62-15 (E)

·

L62-5 (CLG2) - L62-15 (E)*1


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*2

6.

All doors locked through wireless operation



·

*1: Except Driver's Door Only Entry and Start System

·

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).


Waveform 2 (Reference)
Item Content
Terminal No. (Symbol)
·

L62-4 (CG1B) - L62-15 (E)

·

L62-6 (CG2B) - L62-15 (E)*1


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Key not inside vehicle

5.

Key brought outside detection area*2

6.

All doors locked with key



·

*1: Except Driver's Door Only Entry and Start System

·

*2: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).



g.
B251020E04
0.844,1.885 1.031,2.094 0.188,0.208 10 false *a 1.771,1.885 1.958,2.094 0.188,0.208 10 false *b 0.167,1.01 0.5,1.208 0.333,0.198 10 false GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Door open
*b After approximately 30 seconds from when the door is closed

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol)
·

L62-7 (CLG5) - L62-15 (E)

·

L62-8 (CG5B) - L62-15 (E)

·

L62-24 (CLG6) - L62-15 (E)

·

L62-25 (CG6B) - L62-15 (E)

·

L62-26 (CLG7) - L62-15 (E)

·

L62-27 (CG7B) - L62-15 (E)


Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key not inside vehicle

3.

Door is open

4.

Door is closed

5.

30 seconds elapse




h.
B265917E09
0.104,1.01 0.427,1.146 0.323,0.135 10 false GND 1.188,1.969 1.344,2.104 0.156,0.135 10 false *a

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Power switch off, all doors closed and back door opener switch (lock switch) off → on

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) L63-19 (CLG8) - L62-15 (E)*
L63-20 (CG8B) - L62-15 (E)*
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

All doors closed

3.

Back door opener switch (back door lock switch) off → on



*: Except Driver's Door Only Entry and Start System



i.
B251023E18
1.344,0.49 2,0.125 2,0.125 2.219,0.125 true 2.01,0.125 1.76,0.5 true 0.198,1.198 0.531,1.396 0.333,0.198 10 false GND 2.26,0.042 2.438,0.219 0.177,0.177 10 false *a

Using an oscilloscope, check waveform 5.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a In actuality, sampling is being performed

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) L62-18 (TSW1) - L62-15 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Driver door lock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) L62-19 (TSW2) - L62-15 (E)*
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors closed

4.

Front passenger door lock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) L62-20 (SEN1) - L62-15 (E)
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key not sufficiently close to vehicle

5.

Driver door unlock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) L62-21 (SEN2) - L62-15 (E)*
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key not sufficiently close to vehicle

5.

Front passenger door unlock sensor not touched → touched



Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) L62-22 (TSW5) - Body ground*
Tool Setting 2 V/DIV., 500 ms/DIV
Condition Back door opener switch (back door unlock switch) off → on

Waveform 5 (Reference)
Item Content
Terminal No. (Symbol) L62-23 (TSW6) - Body ground*
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Back door opener switch (back door lock switch) off → on

*: Except Driver's Door Only Entry and Start System



j.
B251178E04
0.177,1 0.51,1.198 0.333,0.198 10 false GND 0.969,1.885 1.156,2.042 0.188,0.156 10 false *a 2.01,1.885 2.198,2.042 0.188,0.156 10 false *b

Using an oscilloscope, check waveform 6.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of key pressed
*b After lock or unlock button of key pressed

Waveform 6 (Reference)
Item Content
Terminal No. (Symbol) L63-5 (RCO) - L62-15 (E)
Tool Setting 2 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

Key brought outside detection area*1 but kept inside wireless function operational area*2

4.

Lock or unlock button of key not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).



k.
B251177E05
0.156,1.01 0.49,1.208 0.333,0.198 10 false GND 0.979,1.875 1.167,2.031 0.188,0.156 10 false *a 2.198,1.875 2.385,2.031 0.188,0.156 10 false *b

Using an oscilloscope, check waveform 7.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of key pressed
*b After lock or unlock button of key pressed

Waveform 7 (Reference)
Item Content
Terminal No. (Symbol) L63-15 (RDA) - L62-15 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key brought outside detection area*1 but kept inside wireless function operational area*2

5.

Lock or unlock button of key not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).



l.
B251070E06
0.103,0.984 0.433,1.178 0.330,0.194 10 GND 1.111,1.897 1.294,2.055 0.183,0.158 10 *a 2.065,1.897 2.248,2.055 0.183,0.158 10 *b

Using an oscilloscope, check waveform 8.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Text in Illustration
*a Before lock or unlock button of key pressed
*b After lock or unlock button of key pressed

Waveform 8 (Reference)
Item Content
Terminal No. (Symbol) L63-16 (RSSI) - L62-15 (E)
Tool Setting 5 V/DIV., 500 ms/DIV.
Condition Procedure:
1.

Power switch off

2.

Key brought outside vehicle

3.

All doors locked

4.

Key brought outside detection area*1 but kept inside wireless function operational area*2

5.

Lock or unlock button of key not pressed → pressed



*1: For details about the areas that are outside the entry function detection area, refer to Operation Check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

*2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).




CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U191253E02
1.771,0.573 1.625,0.573 1.625,0.573 1.625,0.854 false 1.552,1.406 1.458,1.406 1.458,1.406 1.458,3.167 false 0.677,2.677 1.021,2.677 false 3.406,7.885 3.667,8.042 0.26,0.156 10 false MB 5.031,6.625 5.292,6.781 0.26,0.156 10 false 2A 1.781,6.583 2.042,6.74 0.26,0.156 10 false 2B 5.063,5.25 5.323,5.406 0.26,0.156 10 false 2C 1.792,5.281 2.052,5.438 0.26,0.156 10 false 2D 4.688,3.969 4.948,4.125 0.26,0.156 10 false 2E 4.979,3.969 5.24,4.125 0.26,0.156 10 false *B 5.656,3.979 5.917,4.135 0.26,0.156 10 false *C 5.354,3.969 5.615,4.125 0.26,0.156 10 false 2F 1.813,3.938 2.073,4.094 0.26,0.156 10 false L7 0.219,2.448 0.479,2.604 0.26,0.156 10 false 2E 0.521,2.448 0.781,2.604 0.26,0.156 10 false *B 0.521,2.74 0.781,2.896 0.26,0.156 10 false *C 0.229,2.74 0.49,2.896 0.26,0.156 10 false 2F 0.417,1.302 0.677,1.458 0.26,0.156 10 false 2D 0.417,2.052 0.677,2.208 0.26,0.156 10 false 2C 1.938,1.438 2.198,1.594 0.26,0.156 10 false L7 1.823,0.5 1.979,0.656 0.156,0.156 10 false *1 3.698,0.552 3.958,0.708 0.26,0.156 10 false MB 6.333,2.083 6.594,2.24 0.26,0.156 10 false 2A 6.323,1.406 6.583,1.563 0.26,0.156 10 false 2B 0.365,0.104 0.625,0.302 0.26,0.198 10 false *A 1.385,3.198 1.542,3.354 0.156,0.156 10 false *2

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 1 connector *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 1 connector

U190870E02
1.781,0.677 1.625,0.677 1.625,0.677 1.625,0.958 false 1.542,1.406 1.458,1.406 1.458,1.406 1.458,3.281 false 1.552,1.698 1.469,1.698 false 1.552,2.052 1.469,2.052 false 0.708,2.781 1.031,2.781 false 3.156,7.594 3.448,7.76 0.292,0.167 10 false MB 4.875,6.385 5.167,6.552 0.292,0.167 10 false 2A 1.885,6.385 2.177,6.552 0.292,0.167 10 false 2B 1.167,5.115 1.458,5.281 0.292,0.167 10 false 2D 0.531,1.5 0.823,1.667 0.292,0.167 10 false 2D 3.927,5.135 4.219,5.302 0.292,0.167 10 false 2C 0.521,2.167 0.813,2.333 0.292,0.167 10 false 2C 4.875,3.802 5.167,3.969 0.292,0.167 10 false L7 6.26,5.104 6.552,5.271 0.292,0.167 10 false 2F 5.594,5.115 5.885,5.281 0.292,0.167 10 false 2E 5.875,5.115 6.083,5.281 0.208,0.167 10 false *B 6.552,5.115 6.76,5.281 0.208,0.167 10 false *C 2.438,3.813 2.729,3.979 0.292,0.167 10 false L8 0.271,2.563 0.563,2.729 0.292,0.167 10 false 2E 0.552,2.583 0.844,2.75 0.292,0.167 10 false *B 0.563,2.854 0.854,3.021 0.292,0.167 10 false *C 0.271,2.854 0.563,3.021 0.292,0.167 10 false 2F 2.01,1.698 2.302,1.865 0.292,0.167 10 false L7 2.01,2.063 2.302,2.229 0.292,0.167 10 false L8 6.271,1.542 6.479,1.708 0.208,0.167 10 false 2B 3.729,0.635 4.021,0.802 0.292,0.167 10 false MB 6.271,2.198 6.479,2.365 0.208,0.167 10 false 2A 1.823,0.583 1.979,0.74 0.156,0.156 10 false *1 0.375,0.198 0.635,0.396 0.26,0.198 10 false *A 1.365,3.313 1.521,3.469 0.156,0.156 10 false *2

Text in Illustration
*A Main Body ECU (Multiplex Network Body ECU) with 3 connectors *B for LHD
*C for RHD - -
*1 Main Body ECU (Multiplex Network Body ECU) *2 3 connectors

a.

Remove the main body ECU from the instrument panel junction block assembly.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
MB-11 (GND1) - Body ground - None - Body ground Ground Always Below 1 Ω -
L8-3 (GND2)* - Body ground - W-B - Body ground Ground Always Below 1 Ω -
MB-30 (BECU) - Body ground Input None - Body ground Auxiliary battery power supply (for CPU) Power switch off 11 to 14 V -
MB-31 (ALTB) - Body ground Input None - Body ground Auxiliary battery power supply (for indicator) Power switch off 11 to 14 V -
MB-29 (ACC) - Body ground Input None - Body ground ACC power supply Power switch on (ACC) 11 to 14 V ACC SW
MB-32 (IG) - Body ground Input None - Body ground Power switch power supply Power switch on (IG) 11 to 14 V IG SW

*: w/ LED Headlight or Glass Roof


If the result is not as specified, there may be a malfunction in the wire harness.


c.

Install the main body ECU to the instrument panel junction block assembly.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item
2D-36 (FRCY) - Body ground Input BR*1 - Body ground
V*2 - Body ground
Front door RH courtesy light switch input Front door RH open Below 1 V FR Door Courtesy
Front door RH closed 11 to 14 V
2D-35 (FLCY) - Body ground Input Y*1 - Body ground
V*2 - Body ground
Front door LH courtesy light switch input Front door LH open Below 1 V FL Door Courtesy
Front door LH closed 11 to 14 V
L7-6 (LRCY) - Body ground Input G - Body ground Rear door LH and RH courtesy light switch input Rear door LH or RH open Below 1 V RL Door Courtesy SW
Rear door LH and RH closed 11 to 14 V RR Door Courtesy SW
L7-19 (BCTY) - Body ground Input L - Body ground Back door courtesy light switch input Back door open Below 1 V Back Door Courtesy SW
Back door closed and luggage compartment light switch on 11 to 14 V
Back door closed and luggage compartment light switch off Pulse generation (See waveform 1 or 2)
2B-8 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2B-9 (ACT+) - Body ground Output R - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2B-10 (ACT+) - Body ground Output P - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2D-12 (ACT+) - Body ground Output L - Body ground Door lock motor lock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Lock side of driver door control switch pushed or driver door key cylinder in lock position 11 to 14 V
2B-1 (ACT-) - Body ground Output B - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
2D-11 (ACT-) - Body ground Output V - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
2B-3 (ACT-) - Body ground Output LG - Body ground Door lock motor unlock drive output Driver door control switch not pushed and driver door key cylinder in neutral position Below 1 V -
Unlock side of driver door control switch pushed or driver door key cylinder in unlock position 11 to 14 V
L7-7 (LSFL) - Body ground Input GR - Body ground Front door LH lock position switch input Front door LH unlocked Below 1 V FL Door Lock Pos
Power switch off, all doors closed and front door LH locked Pulse generation (See waveform 1 or 2)
L7-18 (LSFR) - Body ground Input LG - Body ground Front door RH lock position switch input Front door RH unlocked Below 1 V FR Door Lock Pos
Power switch off, all doors closed and front door RH locked Pulse generation (See waveform 3 or 4)
2D-25 (LSR) - Body ground Input GR - Body ground Rear door LH lock position switch input Rear door LH or RH unlocked Below 1 V RL-Door Lock Pos SW
Power switch off, all doors closed and rear door LH and RH locked Pulse generation (See waveform 3 or 4)
2B-29 (LSR) - Body ground Input GR - Body ground Rear door RH lock position switch input Rear door RH or LH unlocked Below 1 V RR-Door Lock Pos SW
Power switch off, all doors closed and rear door RH and LH locked Pulse generation (See waveform 3 or 4)

*:1 for LHD

*:2 for RHD


If the result is not as specified, the main body ECU (multiplex network body ECU) or instrument panel junction block assembly may have a malfunction.


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) L7-19 (BCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Back door closed and luggage compartment light switch off

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) L7-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door LH locked


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) L7-19 (BCTY) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Back door closed and luggage compartment light switch off

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) L7-7 (LSFL) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door LH locked


g.
B201885E01
0.177,0.962 0.516,1.111 0.339,0.149 10 GND

Using an oscilloscope, check waveform 3.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) L7-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door RH locked

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) 2D-25 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door LH and RH locked

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) 2B-29 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door RH and LH locked


h.
B201886E01
0.152,0.94 0.495,1.108 0.343,0.168 10 GND

Using an oscilloscope, check waveform 4.

HINT:

The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) L7-18 (LSFR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and front door RH locked

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) 2D-25 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door LH and RH locked

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) 2B-29 (LSR) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Power switch off, all doors closed and rear door RH and LH locked