If the entry unlock function does not operate for the driver door only, but the entry lock function operates, the request code is being transmitted properly from the driver door. In this case, there may be a problem related to the touch sensor (connection between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for driver door) [unlock sensor]).
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the power switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FL Door Lock Pos*1 | Front LH door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front LH door unlocked
LOCK: Front LH door locked |
- |
| FR Door Lock Pos*2 | Front RH door unlock detection switch signal / UNLOCK or LOCK | UNLOCK: Front RH door unlocked
LOCK: Front RH door locked |
- |
*1: for LHD
*2: for RHD
On the GTS screen, the display changes between LOCK and UNLOCK as shown in the chart above.
OK
NG
Using the GTS, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D-Door Touch Sensor | Driver door touch sensor (unlock sensor) / ON or OFF | ON: Driver door touch sensor (unlock sensor) touched
OFF: Driver door touch sensor (unlock sensor) not touched |
·
Displays whether the unlock sensor is on or off (even if the sensor is touched and contact is maintained, "ON" is displayed only momentarily). ·
Use this Data List item to help determine if there is an unlock sensor malfunction when the entry unlock function does not operate. |
The GTS display changes correctly in response to the operation of the front door outside handle assembly (for driver door).
OK
NG
Disconnect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.
Disconnect the L62 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
*1: for LHD
*2: for RHD
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| n1-4 (SENS) - L62-20 (SEN1) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| n1-4 (SENS) or L62-20 (SEN1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-4 (SENS) - L62-20 (SEN1) | Always | Below 1 Ω |
| L62-15 (E) - Body ground | Always | Below 1 Ω |
| m1-4 (SENS) or L62-20 (SEN1) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the n1*1 or m1*2 front door outside handle assembly (for driver door) connector.
*1: for LHD
*2: for RHD
| *1 | Waveform | - | - |
| *a | Component with harness connected
(Certification ECU (smart key ECU assembly)) |
*b | In actuality, sampling is being performed |
Connect the L62 certification ECU (smart key ECU assembly) connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| L62-20 (SEN1) - L62-15 (E) | Procedure:
1.
Power switch off 2.
Key brought outside vehicle 3.
All doors locked 4.
Key not sufficiently close to vehicle 5.
Driver door unlock sensor not touched → touched |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
OK
NG